• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.2185-2190
• /
• 2008

In a high speed train, multi-layered panels for floor, side wall and roof are important sound insulating part. As these multi-layered panels require high bending strength vs. weight, corrugated steels or aluminium honeycomb panel are generally used. However, with some inevitable factors, these panels show lower sound insulation performance than that of the plate with the same weight. Transmission loss(TL) often severely decreases in a particular frequency range because of the decrease of the critical frequency, occurrence of local resonance modes and cavity resonance modes, which are not shown in a plate. In this study, frequency range and cause of the TL drop are investigated on the corrugated and honeycomb panels.

• Composites Research
• /
• 제29권3호
• /
• pp.117-124
• /
• 2016

본 연구에서는 스카프 패치로 수리한 복합재 단일겹침 체결부의 파손강도를 시험과 해석으로 연구하였다. 스카프 비, 모재의 적층패턴, 결함크기를 달리 하며 총 45개의 시편에 대한 시험을 수행하여 파손강도와 파손모드를 분석하였다. 다양한 형상의 시편에 대한 시험 결과, 한 경우를 제외하고는 수리 후의 체결부가 결함이 없는 체결부 강도 이상의 강도를 회복하며, 체결부 인자에 따른 특별한 차이는 나타나지 않는 것을 확인하였다. 파손강도가 낮게 나타난 한 경우에 대한 파손면 분석결과 모재의 표면층인 평직층의 표면처리가 충분치 않은 것이 원인인 것으로 판단되었다. 시험 결과의 분석을 위해 3차원 유한요소해석을 수행하였는데, 유한요소해석에서도 고려한 체결부 인자가 상하부 모재와 패치, 접착층에서의 응력에 큰 영향을 미치지 않는 것을 확인하였다. 이는 단일겹침 체결부의 경우 외부 인장하중이 겹침영역을 통과하면서 상하부 모재로 분산되기 때문인 것으로 판단된다. 시험과 해석 결과 모재 중앙에 결함이 존재하는 단일겹침 체결부의 경우 절차에 따라 패치 접착이 이루어지고, 모재의 표면처리가 충분히 이루어진다면 수리를 통해 손상 전 강도를 회복할 수 있는 것으로 판단된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.348-353
• /
• 2012

This paper presents the HRTF based experimental approach to figure out why the human auditory perception on the interior noise source including the directional tonal components does not well match with the dominant features extracted from recorded acoustic signals in terms of psycho-acoustics. Since the general objective evaluation models for tonalness among various sound attributes are a function of width, frequency, excessive level of tonal components respectively, the directional tonal components cannot be properly evaluated without considering the effects of head-related transfer function on the binaural auditory perception. Thus, the directivity of source is additionally considered to prevent the erroneous conclusions from the same sound source in the process of source identification. The signal synthesis technique is used to solve a little difficulty in measuring all of desired acoustic signals for jury evaluation. The sound attributes of synthetic acoustics signals are analyzed to roughly predict the results of jury evaluation in advance by using sound quality factors such as loudness, sharpness, roughness, fluctuation strength and tonality. The jury evaluation is carefully conducted based on the recommended guideline suggested by N. Ottoet al. Each sound is respectively evaluated by selecting a value between -2 and 2 in intervals of 0.2 point. Through above procedure, based on the results of jury evaluation, it is confirmed that serious problems can be caused in the process of analyzing the dominant sound attributes in terms of psycho-acoustics according to the type of a microphone and a playback system.

• 한국소음진동공학회논문집
• /
• 제26권5호
• /
• pp.536-545
• /
• 2016

Household refrigerator radiates noise of which the pattern is dependent on the operating condition of its parts, such as compressor, flow fans, etc. Thus the refrigerator noise has a variety of frequency characteristics. Therefore, it is required to consider the noise characteristics for evaluating the noise quality and eventually developing the sound quality index of the refrigerator noise. In this study, five units of household refrigerator were selected to measure their noises that were used to generate sound sources for jury test of the study. The measured noises of five refrigerators were divided into ten kinds of sound source by considering operating condition and frequency characteristics. Additionally, the ten sources were each edited to have the same SPL of 30 dBA. Totally twenty kinds of sound sources (10-original SPL, 10-edited SPL 30 dBA) were evaluated by twenty-two subjects, and compared with their sound quality metrics. It was found that only the loudness of the metrics was meaningfully correlated with the subjective evaluation. The rests, sharpness, roughness and fluctuation strength, were not related. The conclusion of this study is that a new sophisticated index is necessary to be developed to qualitatively evaluate the household refrigerator noise.

• 한국세라믹학회지
• /
• 제40권3호
• /
• pp.273-278
• /
• 2003

다공질 세라믹스 흡음재료의 흡음특성과 물리.기계적 특성에 미치는 하수슬러지 슬래그 첨가량과 입경 효과에 대하여 조사하였다. 시편의 물리.기계적 특성은 슬래그 입경과 관계 없이 소성온도가 증가하고 슬래그 함량이 감소함에 따라 증가하였으며, 슬래그의 함량이 일정한 시편은 물유리 첨가량이 증가하고 슬래그 입경이 감소함에 따라 증가하였다. 1~3mm 크기의 슬래그를 약 77~89 wt% 함유하고 1,05$0^{\circ}C$에서 2시간 소성한 시편의 부피비중은 1.48~1.71, 압축강도 85~163 kgf/$\textrm{cm}^2$을 나타내었으며, 1~3mm의 슬래그를 이용한 시편은 저주파영역, 슬래그 입경이 1 mm이하인 시편은 고주파영역의 흡음특성이 향상되었으며, 시편의 두께가 증가함에 따라 저주파영역의 흡음특성이 향상되었다.

• International journal of advanced smart convergence
• /
• 제4권1호
• /
• pp.145-153
• /
• 2015

Friction Stir Welding (FSW) is a solid state welding that could successfully weld the difficult-to-weldmaterials such as an aluminum alloy. In this welding process, the stirrer of the welding tool is one of the important factors for producing the perfect sound joint that indicates the higher joint strength. So, this report aims to apply the friction stir welding using various stirrer geometries to weld the AA6063-T1 aluminum alloy butt joint, investigates the mechanical properties of the joint and then compares the mechanical properties with the microstructure of the joint. An experiment was started by applying the friction stir welding process to weld a 6.3 mm thickness of AA6063-T1 aluminum alloy butt joint. A study of the stirrer geometries effect such as a cylindrical geometry, a cone geometry, a left screw geometry and a right screw geometry at a rotational speed of 2000 rpm and a welding speed of 50-200 mm/min was performed. The mechanical properties such as a tensile strength and a hardness of the joint were also investigated and compared with the microstructure of the joint. The results are as follows. A variation of FSW Stirrer shape directly affected the quality AA6063-T1 aluminum alloy butt joint. A cylindrical stirrer shape and a cone stirrer shape produced the void defect at the bottom part of the weld metal and initiated the failure of the joint when the joint was subjected to the load during the tensile test. Left and right screw stirrer shapes gave the sound joint with no void defect in the weld metal and affected to increase the joint strength that was higher than that of the aluminum base metal.

• 자원리싸이클링
• /
• 제22권1호
• /
• pp.20-28
• /
• 2013

국내 자동차 사용이 증가하면서 폐타이어의 재활용에 대한 관심이 고조되고 있다. 폐타이어의 재활용을 위한 처리방법중 분말가공 형태는 25%로서 건설현장에서 다양하게 사용되고 있다. 본 연구에서는 황과 폐타이어를 이용한 콘크리트(SRC: Sulfur-Rubber Concrete)의 물리적 특성을 파악하여 최적배합비를 제안하는데 그 목적이 있다. 이를 위해 황과 폐타이어의 배합양을 달리하여 압축강도 실험을 수행하였다. 더불어 SRC의 제작과정을 2개의 배합방법(건조배합과정 및 습윤배합 과정)에 따라서 각각 그 특성을 평가하였다. 그 결과 고무의 혼입률이 증가할수록 SRC의 압축강도는 감소함을 알 수 있었으며, 마이크로 충진재의 첨가와 황 혼입률 조절은 압축강도를 향상시켰다. 또한 SRC의 황의 혼입률을 조절하여 강도의 최적값을 제안하였다. 이러한 SRC는 도로포장이나 경량벽체 또는 충격에너지 흡수율이 높은 건설 분야에 적용될 수 있을 것으로 판단된다.

• 한국음향학회지
• /
• 제43권3호
• /
• pp.305-313
• /
• 2024

효과적인 양상태 소나 운용을 위해서는 해양환경 요인에 의한 음파전달 특성과 표적의 정보를 반영한 탐지성능 분석이 수행되어야 한다. 하지만 기존의 양상태 소나 탐지성능 분석은 해양환경 및 표적 특성을 고려하지 않거나 단순화되어 수행되었다. 따라서 본 연구에서는 서해와 울릉분지 해역에서 해양환경과 표적의 특성을 고려한 양상태 탐지성능을 산출하였다. 잠수함 형상을 가지는 표적에 대한 양상태 표적강도 도출을 위해 수치해석 모델을 활용하였으며, 모의된 표적강도를 반영하여 신호초과를 계산하였다. 그 결과 송·수신기 위치, 양상태 표적강도에 따라 유의미한 탐지성능 변화가 확인되었다.

• 한국환경생태학회지
• /
• 제29권2호
• /
• pp.174-183
• /
• 2015

We have conducted a verification test of correlation between bird community indices and bird sound recording results in order to use the equipment which deals with the automatic sound collecting system, the song meter. The study areas include four sites which are Gombaeryoung and Zochimryoung in Jeombongsan Mountain and Jookryoung and Gochiryoung in Sobaeksan National Park. We collected the bird sound data five times using a sound recorder and field survey results in the same place of the study site. As a result of the sound recording from the field survey, the species recorded by three researchers of sound analyst include common resident species or species which have a relatively conspicuous call and song. On the contrary, the species recorded by only one researcher are a relatively rare or inconspicuous species or was familiar with the personal experiences of each researcher. The number of species recorded by only one researcher totaled fourteen species (36.8 %), and that of two researchers totaled twelve species (31.6 %), and that of three researchers totaled twelve species (31.6 %). The correlations of the number of species among three researchers was not significant in some results, but the sum or maximum count of the number of species was useful to estimate a significant correlation between the result of researchers and the indices of field surveys. As a result of correlation analysis by using sound recordings, the maximum number of species among the three researchers significantly correlated with the number of species, the species diversity index and the species abundance index in the field survey at the same site, however it did not correlate with the number of individuals and species evenness index. As a result of sound analysis collected from the stationary sound recording system; song meter, the number of frequencies in bird songs and calls correlated with the number of species in the field survey at the same site. The number of calls and songs decreased as time went by. Finally, we could test the active time range and change the activity strength by using a sound recording system. In particular, that sound recording system is able to collect data in same time and site, so it is expected so that the equipment not only replenish a shortage of researchers and survey periods in field research in a short term monitoring survey, but also be able to acquire statistical objectivity.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.83-87
• /
• 2002

Aerospace industries are widely using honeycomb sandwich structures that it has high specific strength and stiffness, chemical material resistance and fatigue resistance. But, in repairing process of damaged areas, one of the problems is that delamination can be occurred in the sound areas during and/or after the exposure to the elevated curing temperature in case that the repair process is repeated. Therefore, this study was conducted Flatwise tensile, Drum peel and Long beam flexural strength tests to evaluate the degree of degradation of mechanical properties of the honeycomb sandwich structures by affecting thermal aging. As the results, the decrease of mechanical strength was observed at the specific specimen which is exposed over 50hrs at $127^{\circ}C$.