• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.323-324
• /
• 2009

We investigated the electrical properties of tris-isopropylsilylethynyl (TIPS)-pentacene organic thin-film transistors (OTFTs) employing Ni/Ag source/drain electrodes. The gap height between the gate insulator and S/D electrode was controlled by changing the thickness of Ag under-layer(20, 30, 40 and 50nm). After evaporating the Ni under-layer, TIPS pentacene channel material was dropping the gap between the gate insulator and SID electrodes. The electrical proprieties of OTFT such as filed-effect mobility, on/off ratio, threshold voltage and subthreshold slope were significantly influenced by the gap height.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 하계종합학술대회논문집
• /
• pp.398-400
• /
• 1998

In this paper, the etching studies for n-GaN were carried out using the wet chemical, the photo-enhanced-chemical, and the electro-chemical etching methods. The experimental results show that n-GaN is etched in diluted NaOH solution at room temperture and the etched thickness of NaOH and electron concentrations. Te etching rate of n-GaN samples with n.simeq.1*10$^{19}$ cm$^{-3}$ were used to compare the photo-enhanced-chemical etching with the electrochemical etching methods. The removed thickness was 680.angs./25min by the electrochemical etching methods. The removed thickness was 680 .angs./25min by the electrochemical etching method ad 784.angs./25min by the photoenhanced-chemical etching method. The patterns are 100.mu.m*100.mu.m rectangulars covered with SiO$_{2}$film. It is shown that the profile of etched side-wall of the pattern is vertical without dependance of the n-GaN orientations.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1728-1731
• /
• 1996

To develop more sensitive humidity sensor on high temperature region, in this paper, we prepared polyimide humidity sensor by electrophoretic method. Sensing properties of be sensor in high temprature region were studied and compared with that prepared by solution casting method. From the result, the thiner film thickness, the more sensitive. however, It is difficult to make he thickness optimal because of short between electrodes, and the thickness of upper electrode is one of most important parameters affecting pefomance of the sensor.

• Current Photovoltaic Research
• /
• 제1권1호
• /
• pp.44-51
• /
• 2013

For preparing a device-quality $CuInSe_2$ (CISe) light-absorbing layer by single-bath electrodeposition for a superstrate-type CISe cell, morphological properties of the CISe layers were investigated by varying concentrations of sulfamic acid and potassium biphthalate, complexing/buffering agents. CISe films were grown on an $In_2Se_3$ film by applying a constant voltage of -0.5V versus Ag/AgCl for 90 min in a solution with precursors of $CuCl_2$, $InCl_3$, and $SeO_2$, and a KCl electrolyte. A dense and smooth layer of CISe could be obtained with a solution containing both sulfamic acid and potassium biphthalate in a narrow concentration range of combination. A CISe layer prepared on the $In_2Se_3$ film with proper concentrations of complexing/buffering agents exhibited thickness of $1.6{\sim}1.8{\mu}m$ with few undesirable secondary phases. On the other hand, when the bath solution did not contain either sulfamic acid or potassium biphthalate, a CISe film appeared to contain undesirable flake-shape $Cu_{2-x}Se$ phases or sparse pores in the upper part of film.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.176-179
• /
• 2000

In the recognition of the gases using the quartz crystal microbalance (QCM) coated with the film materials, it is important to obtain the recognition ability of gases, and the stability of film coated above the QCM. Especially, the thickness of film coated above the QCM is decreased according with the using circumstance and time of QCM gas sensor. Therefore, the sensing chararcteristics of film is changed with these. In this paper, we coated the lipid PC (Phosphatidyl Choline) materials varing with the blended amount of PVC(Poly Vinyl Chloride) and solution (Tetra Hydrofan:THF) above QCM to obtain the stability of lipid PC film. QCM gas sensors coated with film materials were measured the frequency change in the chamber of stationary gas sensing system injected 1-hexane, ethyl acetate, ethanol and benzene of $20{\mu}{\ell}$, respectively. We obtained the principal component analysis (PCA) from the frequency change due to the absorption of gas. Also, we measured the degradation characteristics of QCM gas sensor to show the properties of stability.

• 분석과학
• /
• 제7권2호
• /
• pp.181-186
• /
• 1994

Poly(3-methylthiophene) 전도성 막전극을 이용해서 벗김 전압-전류법으로 Ag의 분석 가능성을 연구하였다. 막전극 표면에 존재하는 18-crown-6은 수용액에서 Ag(I)을 착화에 의해서 흡수하고 이 Ag(I)은 제한된 전위 범위의 순환 전압-전류법에 의해서 막전극 속으로 이동하여 유리질 탄소전극에서 산화-환원된다. 따라서 막전극은 Ag(I)의 침투를 용이하게 하기 위해서 적당한 두께의 다공성으로 제조되어야 한다. 이러한 실험 결과를 바탕으로 수용액에서 $5.0{\times}10^{-6}M$의 Ag(I)을 검출할 수 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 학술대회 논문집 전문대학교육위원
• /
• pp.44-47
• /
• 2000

In the recognition of the gases using the quartz crystal microbalance (QCM) coated with the film materials, it is important to obtain the recognition ability of gases, and the stability of film coated above the QCM. Especially, the thickness of film coated above the QCM is decreased according with the using circumstance and time of QCM gas sensor. Therefore, the sensing characteristics of film is changed with these. In this paper, we coated the lipid PC (Phosphatidyl Choline) materials varing with the blended amount of PVC(Poly Vinyl Chloride) and solution (Tetra Hydrofan:THF) above QCM to obtain the sensitive and the stability of lipid PC film. QCM gas sensors coated with film materials were measured the frequency change in the chamber of stationary gas sensing system injected 1-hexane, ethyl acetate, ethanol and benzene of $20{\mu}{\ell}$, respectively. We also measured the degradation characteristics of QCM gas sensor to show the properties of stability.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.656-658
• /
• 2004

Pb$(Zr_{0.8}Ti_{0.2})TiO_3$ powder were prepared by the sol-gel method using a solution of Pb-acetate, Zr n-propoxide and Ti iso-propoxide. PZT thick film were fabricated by the screen printing method, and the structural and ferroelectric properties asafunting of the sintering temperature were studied. PZT film thickness, obtained by four screen printing, was approximately $70\sim90{\mu}m$. The relative dielectric constant and the dielectric loss of the PZT thick film sintered at $1050^{\circ}C$t were approximately 676 and 1.4%, respectively. The remanent polarization and the coercive field of the PZT thick film sintered at $1050^{\circ}C$ were $21.15{\mu}C/cm^2$ and 10.1 kV/cm, mapetively

• Structural Engineering and Mechanics
• /
• 제50권5호
• /
• pp.697-708
• /
• 2014

The intentional buckling design of micro-films has various potential applications in engineering. The buckling amplitude and critical strain of micro-films are the crucial parameters for the buckling design. In the reported studies, the film parameters were regarded as deterministic. However, the geometrical and physical parameters uncertainty of micro-films due to manufacturing becomes prominent and needs to be considered. In the present paper, the probabilistic nonlinear buckling analysis of micro-films with uncertain parameters is proposed for design accuracy and reliability. The nonlinear differential equation and its asymptotic solution for the buckling micro-film with nominal parameters are firstly established. The mean values, standard deviations and variation coefficients of the buckling amplitude and critical strain are calculated by using the probability densities of uncertain parameters such as the film span length, thickness, elastic modulus and compressive force, to reveal the effects of the film parameter uncertainty on the buckling deformation. The results obtained illustrate the probabilistic relation between buckling deformation and uncertain parameters, and are useful for accurate and reliable buckling design in terms of probability.

• Corrosion Science and Technology
• /
• 제15권3호
• /
• pp.120-124
• /
• 2016

The effect of alloying element Ca (0, 1, and 2 wt%) on corrosion resistance and bioactivity of the as-received and anodized surface of rolled plate AM60 alloys was investigated. A plasma electrolytic oxidation (PEO) was carried out to form anodic oxide film in $0.5mol\;dm^{-3}\;Na_3PO_4$ solution. The corrosion behavior was studied by polarization measurements while the in vitro bioactivity was tested by soaking the specimens in Simulated Body Fluid (1.5xSBF). Optical micrograph and elemental analysis of the substrate surfaces indicated that the number of intermetallic particles increased with Ca content in the alloys owing to the formation of a new phase $Al_2Ca$. The corrosion resistance of AM60 specimens improved only slightly by alloying with 2 wt% Ca which was attributed to the reticular distribution of $Al_2Ca$ phase existed in the alloy that might became barrier for corrosion propagation across grain boundaries. Corrosion resistance of the three alloys was significantly improved by coating the substrates with anodic oxide film formed by PEO. The film mainly composed of magnesium phosphate with thickness in the range $30-40{\mu}m$. The heat resistant phase of $Al_2Ca$ was believed to retard the plasma discharge during anodization and, hence, decreased the film thickness of Ca-containing alloys. The highest apatite forming ability in 1.5xSBF was observed for AM60-1Ca specimens (both substrate and anodized) that exhibited more degradation than the other two alloys as indicated by surface observation. The increase of surface roughness and the degree of supersaturation of 1.5xSBF due to dissolution of Mg ions from the substrate surface or the release of film compounds from the anodized surface are important factors to enhance deposition of Ca-P compound on the specimen surfaces.