• Elastomers and Composites
• /
• 제39권1호
• /
• pp.51-60
• /
• 2004

본 연구에서는 organoclay를 혼합한 NR/BR blend의 가황특성, 동적점탄성 및 기계적 물성을 carbon black 및 silica를 함유한 배합고무와 비교 평가하였다. Solution 혼합법을 이용함으로써 광범위한 나노 복합체를 제조할 수 있었으며, 충전제의 함량은 10phr로 고정하였다. XRD 실험으로 clay의 삽입 및 박리정도를 측정하였다. 통상적인 혼합법을 이용할 경우 clay의 박리 또는 삽입정도가 미약한 반면 solution 혼합법을 이용할 경우 광범위한 박리형태의 clay 배합고무를 얻을 수 있음을 확인하였다. Clay 배합고무는 carbon black 및 silica를 함유한 배합고무에 비해 높은 tan ${\delta}$값을 나타내며, solution 혼합법을 이용할 경우 통상적인 혼합법에 의해 제조된 clay 배합고무에 비해 우수한 기계적 물성을 가짐을 확인할 수 있었다.

• 한국세라믹학회지
• /
• 제36권9호
• /
• pp.893-900
• /
• 1999

Silica films were prepared on Si single crystal substrates by sol-gel process using TEOS as starting materials. Films were fabricated by a spin coating technique. Sol solutions were prepared by varying the compositions of CH3OH, H2O and DMF with fixed molar ratio of TEOS=1, HCl=0.05(mol). Wetting behavior viscosity of solutions gelation time thickness of films and cracking behavior were investigated with the various solution compositions. Wetting behaviors of solutions depended on the solution compositions mixing method and mixing rate. The optimum composition of sol was TEOS : DMF ; CH3OH: H2O :HCl=1:2:4:4:0.05(mol) and the mixing rate of solution was optimized at 1 ml/min. Viscosity of solutions were controlled by choosing a reaction time(elapsed time after mixing) at a room temperature so that we could get up to 800nm thick film The surface roughness was getting poor when thickness of films was thicker than 500nm. Thickness of coated films were increased with decreasing amount of CH3OH. The best surface roughness was obtained at the content of CH3OH 4 mol. The shortest gelation time was obtained with the content of CH3OH 8 mol. Crack-free filkms were fabricated when sintered at 500$^{\circ}C$ for 1 hr with heating rate of 0.6$^{\circ}C$/min.

• 청정기술
• /
• 제23권1호
• /
• pp.42-53
• /
• 2017

탈질과 탈황을 동시에 수행하는 과산화수소($H_2O_2$) 수용액 세정탑의 반응효율을 증가시키기 위해 예혼합이 이루어지는 혼합 냉각기(mixing quencher) 영역 내부의 유체유동에 대한 수치해석이 수행되었다. 산업공정에서 상용화되고 있는 세정탑 전단부의 혼합냉각기에서 과산화수소 수용액이 주입되는 노즐의 분사방식은 배기가스와 과산화수소 수용액의 혼합에 중요한 역할을 하며, 혼합냉각기에서의 혼합도는 세정탑 의 효율을 결정하는 중요 요소가 된다. 본 연구에서는 혼합냉각기 내부유체의 농도분포 개선을 목적으로 하여 혼합냉각기 내의 노즐 관의 배열을 조절하거나 노즐 팁 각도를 변경하며 유체혼합을 최적화하였다. 전산해석은 이 냉각기영역의 내부유동 및 각 유체 농도에 대한 RMS (root mean square) 값을 계산하여 내부유체의 혼합도의 개선을 확인하였다. 세부적으로는 노즐 관의 위치를 조절할 때 변경되는 냉각기 영역 후단의 농도 RMS 값을 확인하여 난류형성위치에 따른 최적화된 혼합도를 확인하였으며 기본형상 대비 난류형성방향을 조절하는 목적의 노즐 팁 각도를 증감하여 농도분포의 균질화를 비교하였다. 노즐 관의 배열에 따라 난류형성위치와 그에 따른 유체혼합이 해석되었다. 또한 노즐 팁 각도를 조절하는 경우에는 유동방향과의 각도에 따라, 흐름이 병류와 향류에 따라 혼합도의 최적화를 확인할 수 있었다. 노즐 관의 위치는 0.3 m, 노즐 팁은 병류의 $15^{\circ}$일 때 최적의 조건을 가지며 가장 낮은 RMS 값인 12.4%를 가졌다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 추계 학술대회논문집
• /
• pp.49-55
• /
• 2007

The quality of chaotic mixing in three-dimensional micro channel flow has been numerically studied using Fractional-step method (FSM) and particle tracking techniques such as $Poincar{\acute{e}}$ section and Lyapunov exponents. The flow was driven by pressure distribution and the chaotic mixing was generated by applying alternating current to electrodes embedded on the bottom wall at a first half period and on the top wall at a second half period. The equations governing the velocity and concentration distributions were solved using FSM based on Finite Volume approach. Results showed that the mixing quality depended significantly on the modulation period. The modulation period for the best mixing performance was determined based on the mixing index for various initial conditions of concentration distribution. The optimal values of modulation period obtained by the particle tracking techniques were compared with those from the solution of concentration distribution equation using FSM and CFX software and the comparison showed their good match.

• 대한화학회지
• /
• 제6권2호
• /
• pp.122-124
• /
• 1962

The silver halide precipitate tends to separate in curdy form of flocculated colloid when it is precipitated by direct mixing of reactant solutions. This type of precipitate has a great tendency to adsorb or occlude foreign ions in the solution.When silver halide in precipitated from homogeneous solution using the slow hydrolysis of Alkyl halide or Ally halide, the precipitate becomes dense, filterable and uniform in particle size which is very advantageous in gravimetric analysis.We found that silver halide precipitates obtained from homogeneous solution with hydrogen halide formed by the hydrolysis of alkyl halide do not give the color change with fluorescein as adsorption indicater, while silver halide precipitates obtained by direct mixing method give sharply pink color which appear to be uniformly distributed through the solution in silver ion excess.

• 한국염색가공학회지
• /
• 제9권1호
• /
• pp.23-32
• /
• 1997

Composite membranes having different mixing ratio of Wool(SCMK) and poly(ethylene terephthalate) (PET) were prepared by dissolving wool/PET in hexafluoro-2-propanol(HFIP), casting the obtained solution on a glass plate and evaporation the solvent in the presence and absence of an electric field. The internal structure of the prepared membrane was investigated using polarise microscope dyeing and dye permeation method. In the composite membrane prepared under electric field, both components were micro mixing, while in the membranes prepared under nonelectric field, the two components formed a random sea/island structure according to different mixing ratio. Such characteristic membrane structure was influenced the permeation behavior of C.I. Acid Red 118 through the membranes from an aqueous solution.

• Journal of Biosystems Engineering
• /
• 제22권4호
• /
• pp.469-478
• /
• 1997

This study was conducted to develop an automatic nutrient-solution mixing system for small-scale sewers. The nutrient-solution mixing system consisted of a low-cost and precise metering device and data acquisition ＆ control system with a personal computer. and, the metering device was composed of three parts those were supply pumps, metering cylinders and venturi tube. The system controlled electric conductivity(EC) and pH of nutrient-solution based on the time-based feedback control method with the information about temperature, EC, and pH of the nutrient-solution. The performance of the nutrient-solution mixing system was evaluated through the control of EC and pH while compared with those of commercial system. Also an experimental cultivation of tomato was conducted to verify and to improve the developed system. Results of this study were as follows. 1. The correlation coefficient of meteing device between the flow rate and operating time was 0.9999, and the linear reuession equation computed was y=21.759x, where y is the discharge($g$) and x is the operating time(s). 2. Calculated errors for the developed metering device and two commercial pump were $\pm$0.3% $\pm$2.45% and $\pm$1.38 % FS error respectively. 3. An automatic nutrient-solution mixing system based on a low-cost and precise metering device was developed. 4. The full scale errors of the developed system in controlling EC and pH at 23$\pm$1$^{\circ}C$ were $\pm$0.05mS/cm and $\pm$0.2, respectively 5. When using the commercial system, the controlled values of EC and pH of the 500 $\ell$ of water were 1.29 mS/cm and 6.1 pH for the setting points of 1.4 mS/cm and 6.0 pH respectively at 23$pm1^{\circ}C$. 6. The developed nutrient-solution control system showed $\pm$0.05 ms/cm of deviation from the setting EC value over the experimental cultivation period. 7. The deviation from the average values of Ca and Mg mass content in the several nutrient-solution were 0.5% and 1.8% respectively.

• 설비공학논문집
• /
• 제9권1호
• /
• pp.43-54
• /
• 1997

This paper presents an approximate analytical solution to a two-region one-dimensional model for the charging process of stratified thermal storage tanks with variable inlet temperature in the presence of momentum-induced mixing. Based on the superposition principle, an arbitrary-varying inlet temperature is decomposed into inherent discontinuous steps and continuous intervals approximated as a finite number of piecewise linear functions. This approximation allows the temperature of the upper perfectly-mixed layer to be expressed in terms of constant, linear and exponential functions with respect to time. Applying the Laplace transform technique to the model equation for the lower thermocline layer subject to each of three representative interfacial conditions yields compact-form solutions, a linear combination of which constitutes the final temperature profile. A systematic method for deriving solutions to the plug-flow problem having polynomial-type boundary conditions is also established. The effect of adiabatic exit boundary on solution behaviors proves to be negligible under the actual working conditions, which justifies the assumption of semi-infinite domain introduced in the solution procedure. Finally, the approximate solution is validated by comparing it with an exact solution obtained for a specific variation of inlet temperature. Excellent agreements between them suffice to show the necessity and utility of this work.

• 한국공작기계학회논문집
• /
• 제16권6호
• /
• pp.146-152
• /
• 2007

An active micro-mixer, which was composed of an oscillating micro-stirrer in the microchannel to provide rapid, effective mixing at high flow, rates was analyzed. The effects of molecular diffusion and disturbance by the stirrer were considered with regard to two types of mixer models: the simple straight microchannel and microchannel with an oscillating stirrer. Two types of mixer models were studied by analyzing mixing behaviors such as their interaction after the stirrer. The mixing was calculated by Lattice Boltzmann methods using the D2Q9 model. In this study, the time-averaged mixing index formula was used to estimate the mixing performance of time-dependent flow. The mixing indices of the two models compared. From the results, it was found that the mixer with an oscillating stirrer was much more enhanced and stabilized. Therefore, an optimum design for a dynamic micro-mixer with an oscillating stirrer was performed using Taguchi method in order to obtain a robust solution. The design parameters were established as the frequency, the length and the angle of the stirrer and the optimal values were determined to be 2, 0.8D and ${\pm}75^{\circ}$, respectively. It was found that the mixing index of the optimal design increased 80.72% compared with that of the original design.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.151-154
• /
• 2004

Despite of the excellent properties of carbon nanofiber, The properties of carbon nanofiber filled polymer composites were not increased largely. The reason is that it is still difficult to ensure the uniform dispersion of carbon nanofiber in a polymer matrix. In this study, For improvement properties of carbon nanofiber filled epoxy composites, the effect of dispersion was investigated. The compounds were prepared by two methods, solution blending and mechanical mixing. Mixing of solution blending method was used using ultrasonic. Dispersion of carbon nanofiber was observed by optical microscope and scanning electron microscope (SEM). UV adsorption and turbidity measured by UV spectrometer was used for the comparison of dispersion of carbon nanofiber.