• Journal of the Korean Magnetics Society
• /
• v.14 no.6
• /
• pp.228-231
• /
• 2004

We have studied local magnetization reversal and magnetic properties induced by Laser annealing method in the strip-patterned Ta/NiFe/FeMn/Ta and Ta/NiFe/FeMn/NiFe/Ta multilayers fabricated by ion-beam deposition. The films were exposed to the emission of the DPSS (Diode Pumped Solid State, Nd:YAG) laser under 600 G. The laser beam intensity increased up to 440 mW. When the laser illuminated the patterned film with the power of above 200 m W, the intensity of MR peak located in +87 Oe shrunk. A new MR peak was generated at -63 Oe. When the laser power is 400 mW, the location of positive MR peak(H$\sub$ex/) was changed slightly from +87 Oe to +76 Oe, and the MR ratio was decreased from 0.9% to 0.1 %. On the other hand, the new (negative) MR peak shifted from -63 Oe to -80 Oe, with the MR ratio increased up to 0.3%. As the illuminated area expanded, the intensity of opposite MR peak increased and it of negative MR peak decreased. This proved that the local reversal of exchange biasing should be realized by laser annealing.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.4 s.33
• /
• pp.1-5
• /
• 2004

A multi-layer flexible substrate is composed of copper(Cu)/polyimide that are known as good electrical conductivity, and low dielectric constant, respectively. In this study. conductor line of $5{\mu}m$-pitch was successfully fabricated without non-uniform pattern shape by electroplating copper and coating polyimide on patterned stainless steel. For multi-layer flexible substrate, via holes were drilled by UV laser and filled with electroplating copper and tin. And then, the PI layer with vias and conductor lines was stripped from stainless steel substrate. The PI layers were laminated at once with careful alignment between layers. Solid state reaction between tin and copper during lamination formed the intermetallic compounds of $Cu_6Sn_5$($\eta$-phase) and $Cu_3Sn$($\epsilon$-Phase) and achieved a complete inter-connection by vertically positioning the plugged via holes on via pad. The via formation process has several advantages; such as better electrical property and lower cost than V type via and paste via.

• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.85-91
• /
• 2003

Intracavity frequency doubling of a single-mode Nd:YAG laser by using a nonplanar ring cavity is demonstrated. The nonplanar ring cavity consists of a Brewster-angled Nd:YAG crystal placed in a magnetic field, a KTP crystal, and two spherical mirrors. In this design the Nd:YAG block acts as both a nonreciprocal polarization rotator and a partial polarizer, and the nonplanar portion of the ring cavity, which is formed by a relative twist angle between the Brewster-angled end surfaces of the Nd:YAG block, serves as a reciprocal polarization rotator. An eigenpolarization theory for the cavity configuration is presented and suitable values of the relative twist angle for unidirectional operation are estimated. A single-mode output power of 22 ㎽ at 532 nm and an optical to optical conversion efficiency of 1.8% are obtained with a 1.2 W diode laser at 809 nm.

• Korean Journal of Optics and Photonics
• /
• v.13 no.2
• /
• pp.140-145
• /
• 2002

We measured the absorption rate of a Nd:YVO$_4$crystal with a thickness of 1 mm and the output power characteristics of a cw Nd:YVO$_4$/KTP laser with respect to the change of wavelength and the polarizations of a tunable Ti:sapphire pump laser with a linewidth of 0.2 nm. In the case of S-polarization (E┴$\pi$) and P-polarization (E∥$\pi$) of a pump laser, the maximum absorption rate of the crystal was 82% at 809.4 nm and 98% at 808.8 nm, and slope efficiencies for the output power of the Nd:YVO$_4$laser (1064 nm) were 43% and 52%, respectively. The maximum Nd:YYO$_4$laser output power of 516 mW was obtained from the P-polarization pump laser of 1000 mW. As a result of an intracavity frequency-doubling, slope efficiency for the output power of the Nd:YVO$_4$/KTP green laker (532nm) was 23% and the maximum output power of 205 mW with the beam quality (M$^2$) of 1.42 was obtained from the P-polarization pump laser of 1000 mW.

• Korean Journal of Optics and Photonics
• /
• v.18 no.4
• /
• pp.270-273
• /
• 2007

We have investigated the output characteristics of the 946 nm Nd:YAG laser which is longitudinally pumped by a fiber coupled laser diode. The temperature of a Nd:YAG crystal mount was kept constant by a controller with thermoelectric cooler. As a result, we measured more intense output at a low temperature, and then the maximum output power was measured to be 870 mW when the pumping power and the temperature were 9.95 W and $5^{\circ}C$, respectively. It appeared that output was decreased above 10 W pump power because of the thermal effects in gain medium.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.631-634
• /
• 2004

The method that exists in Photodynamic Therapy uses Photosensibility drug strongly Influencing tumour accumulation together with photochemical laser effect and makes the structure of tumour be localized and become extinct. The intracavity transformation of the Nd :YAP main radiation 1079 nm was Raman converted in barium nitrate crystal and the Stokes frequency (1216 nm) was doubled using KTP or RTA crystals. The LiF or Cr:YAG crystals are used for the Q-switch. The radiation Parameters were obtained at 100 Hz pump repetition frequency. The average power at 608 nm radiation with LiF and KTP was 700 mW at multi-mode generation. The 3-6 single 10-15 ns pulses were generated during one cycle of pumping. The doubling efficiency with RTA was two times more than with KTP. The cells of Ehrlich adenocarcinoma (0.1 ml) were i.m. implanted in hind thighs of ICR white non-imbred mice. The cells were preliminarily diluted in medium 199 in the ratio of 1 to 5. HpD was intravenous administered in a dose of 10 mg/kg. The left clean-shaven hind leg was irradiated with laser light 21-27 hours after the administration of the preparation. The right non-Irradiated leg of each animal served as a control. The animals with the transplanted tumor that were not injected with HpD sewed as a control to estimate the complex effect (HpD+ irradiation). Before the administration of HpD and on 3 and 4 days after irradiation the tumor size was measured and the percent of the tumor growth inhibition was calculated. The results of animal treatments has shown high efficiency of PDT method for cancer treatment by means 0.608 m high power pulse solid state laser.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.3
• /
• pp.312-317
• /
• 2014

In this paper, I propose the design technology of LLC resonant converter for the xenon flashlamp that is used to the solid state laser. Through the fabrication of 1.5kW large scale LLC resonant converter, the discharge characteristics are carried out, and introduce the new control method for limiting inrush current by the abrupt load current changes. The mathematical modeling for the lamp discharge includes the internal loss and lamp parameters. I propose the optimal method for the driving conditions of xenon flashlamp from the simulation results comparing the real measurements.

• Journal of the Korean Ceramic Society
• /
• v.44 no.5 s.300
• /
• pp.151-154
• /
• 2007

Yttrium aluminum garnet, $Y_3Al_5O_{12}$ (YAG) is an extensively used solid-state laser host material. YAG nanocrystals were synthesized using low-temperature glycol method, a modified sol-gel method performed at low temperature that consists of a mixture of salts that are mostly nitrates in an aqueous media. Single-phase nanocrystalline YAG was obtained at $850^{\circ}C$, which is a much lower temperature than with other techniques such as a wet-chemical technique. The structural characterization is done by powder X-ray diffraction, scanning electron microscopy and transmission electron microscopy. A crystallite size range of 20-50 nm was observed for the materials prepared at $850-950^{\circ}C$.

• Korean Journal of Optics and Photonics
• /
• v.13 no.4
• /
• pp.347-355
• /
• 2002

We have constructed a high efficiency and broad tunable cw Ti:sapphire laser with a four-mirror symmetric Z-type laser cavity to increase the laser usability. From theoretical analyses and experimental data for a symmetric Z-type laser cavity containing a Kerr medium, the cavity mode size and the Kerr-lens mode-locking (KLM) strength for KLM lasers can be confirmed as function of the position in the cavity, the intracavity laser power, and the stability parameter. As a result, the slope efficiency and the maximum average output power of cw Ti:sapphire laser at 5 W pumping power of Ar-ion laser were 31.3% and 1420 ㎽ respectively. The tunablility was ranged from 730 ㎚ to 908 ㎚ with average output power above 700 ㎽. We obtained the KLM operation easily by self-aperturing effect in the Kerr medium and the slope efficiency and the maximum average output power of KLM Ti:sapphire laser was 16% and 550 ㎽ respectively. The spectral bandwidth was 33 ㎚ at the center wavelength of 807 ㎚ and the pulse width was 27 fs with a repetition rate of 82 ㎒.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.130-133
• /
• 2009

$Cu_2ZnSnSe_4$(CZTSe) is one of the promising materials for the solar cell due to its abundant availability in the nature. In this study, we report the fabrication of CZTSe thin film by Pulsed Laser Deposition(PLD) method using quaternary compound target on sodalime glass substrate. The quaternary CZTSe compound target was synthesized by solid state reaction method using elemental powders of Cu, Zn, Sn and Se. Powders were milled in high purity ethanol using zirconia ball with mixed size of 1 and 3 mm at the same proportions for 72 hours milling time. The structural, chemical and mechanical properties of the synthesized CZTSe powders were investigated prior to the deposition process. The CZTSe compound powder, and $500^{\circ}C$ of sintering temperature shows the best properties for PLD target. Results show that the as-deposited CZTSe thin films with the precursors by PLD have a composition near-stoichiometric.