• Environmental Engineering Research
• /
• v.13 no.3
• /
• pp.112-118
• /
• 2008

Residual solid in excess sludge treated by hydrothermal reaction was investigated as raw material for its recycling. Treated excess sludge and residual solid were also focused on their content change during hydrothermal reaction. Two kinds of excess sludge, obtained from a local food factory and a municipal wastewater treatment process, were tested under various conditions. Following hydrothermal reaction, depending on the reaction conditions, biodegradable substrates in treated excess sludge appeared to increase. The separated residual solid was a composite composed of organic and inorganic materials. The proportion of carbon varied from 34.0 to 41.6% depending on reaction conditions. Although 1.89% of hazardous materials were detected, SiO2 (Quartz) was a predominant constituent of the residual solid. X-ray diffraction (XRD) experiments revealed that the residual solid was of a partially amorphous state, suggesting that the residual solids could be easily converted to stable and non harmful substances through a stabilization process. Thus, this technology could be successfully used to control excess sludge and its reuse.

• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.3
• /
• pp.267-276
• /
• 2010

Many plants have been improved to adapt the target of the biological treatment processes changed from organics to nutrients since the water quality criteria of effluent was reinforced and included T-N and T-P for the municipal wastewater treatment plant. To meet the criteria of T-N and T-P, the conventional biological reactor such as aeration tank in activated sludge system is changed to the BNR (biological nutrient removal) processes, which are typically divided into three units as anaerobic, anoxic and oxic tank. Therefore, the solid separation process should be redesigned to fit the BNR processes in case of the application of the DAF (dissolved air flotation) process as an alternatives because the solid-liquid separation characteristics of microbial flocs produced in the BNR processes are also different from that of activated sludge system as well. The results of this study revealed that the microbial floc of the anaerobic tank was the hardest to be separated among the three steps of the unit tanks for the BNR processes. On the contrary, the oxic tank was best for the removal efficiency of nutrients as well as suspended solid. In addition, the removal efficiency of nutrients was much improved under the chemical coagulation treatment though coagulation was not indispensable with a respect to the solid separation. On the other hand, in spited that the separation time for the microbial floc from the BNR processes were similar to the typical particles like clay flocs, over $2.32{\times}10^3$ ppm of air volume concentration was required to keep back the break-up of the bubble-floc agglomerates.

• Journal of Korean Society on Water Environment
• /
• v.32 no.6
• /
• pp.600-627
• /
• 2016

Korea is one of the countries with a large veterinary antibiotics market, although antimicrobial resistance in bacteria is becoming a serious issue in many countries. The Korean government started to take interest in estimating the effects of livestock manure on rivers and agricultural soils and in monitoring of heavy metals, organic pollutants and antibiotics in the ambient water and soil. In this paper, pre-treatment methods to separate the selected antibiotics from solid samples were reviewed. It is essential to select an efficient and appropriate procedure for pre-treatment due to the high proportion of proteins and organics in biosolid samples. Pre-treatment consists of extraction followed by clean-up. Initially, homogenized samples were extracted by sonication, mechanical agitation or pressurized liquid extraction with methanol/acetonitrile/water mixture under acidic/basic conditions depending on the compound. However, aminoglycosides and colistin were extracted with 5% trichloroacetic acid and HCl, respectively. Since the ${\beta}-lactams$ are easily decomposed in acidic and basic conditions, they were extracted in neutral pH. Filtration with a membrane (pore size, $0.2{\mu}m$) or solid phase extraction with HLB and methanol, as eluents, was normally applied for the clean-up. At least, three different pre-treatment procedures should be adopted to screen all the selected antibiotics in solid samples.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.322-322
• /
• 2011

White gold는 아름다운 광택과 손쉬운 가공성의 장점 때문에 장신구를 비롯한 다양한 분야에서 그 활용 가치가 매우 높다. 본 연구에서 우리는 열처리를 통한 white gold의 hardness강화 및 품질향상을 위하여 다양한 열처리 조건별 기계적 특성변화를 비교 관찰 하였다. 열처리 전 white gold alloy의 구성성분을 조사하기 위하여 EPMA와 ICP-MS를 사용하여 분석 후 그 값을 수치화 하였다. 14K, 18K White gold alloy 총 32개의 시료를 사용하여 $750^{\circ}C$, 30 min의 조건에서 solid treatment 및 quenching 후 $200^{\circ}C{\sim}350^{\circ}C$ 온도 범위에서 $50^{\circ}C$ 간격으로 age-hardening을 실시하였다. 열처리 전과 후 각 조건별 hardness 변화는 Vicker's hardness tester를 사용하여 측정하였다. 또한 age-hardening 후 모든 시료는 optical microscope (OM)을 사용하여 각 열처리 조건 별 grain 들의 배열 및 size의 변화를 관찰하였다. 열처리 전 14K, 18K white gold alloy의 hardness의 평균값은 각각 162 Hv와 196 Hv를 나타내었다. solid treatment 후 그 수치가 146 Hv, 172 Hv로 감소하였고, age-hardening 후에는 hardness 값이 점차 증가하여 14K는 $260^{\circ}C$에서 226 Hv, 18K는 $270^{\circ}C$에서 268 Hv의 가장 높은 수치를 나타내었다. 또한 14K 및 18K는 각각 $260^{\circ}C$, $270^{\circ}C$ 이상에서는 over-aging 현상을 나타내었다. OM 분석 결과 열처리 전 불균일했던 grain들의 배열이 solid treatment 및 quenching 후 다소 균일해짐을 확인할 수 있었고, grain size 또한 열처리 전에 비해 증가함을 알 수 있었다. Solid treatment 후 모든 시료의 hardness값이 전반적으로 감소하였다가 age-hardening을 통해 grain들의 배열이 점차 안정화 되면서 hardness가 증가 하였고, over-aging 구간에서는 급격히 감소하는 경향을 나타내었다. 이 결과들로부터 우리는 14K, 18K white gold alloy 에 대한 age-hardening 최적조건을 도출하였고, 각 열처리 조건별 grain 배열 상태의 변화를 관찰 할 수 있었다.

• Journal of Korea Foundry Society
• /
• v.38 no.1
• /
• pp.1-8
• /
• 2018

In this study, we focused on the correlation between the solidification structure, heat treatment and mechanical properties of the A356 alloy according to the conditions of Sr modification. The microstructural evolution of the eutectic Si and ${\alpha}-Al$ phase in the A356 alloy castings depending on the amount of Sr were investigated during solid solution heat treatment using an optical microscope, a scanning electron microscope and an image analyzer. In addition, tensile tests on the heat treated materials examined the relationship between the microstructure and the fracture surface. The as-cast A356 alloys under 40 ppm Sr showed an undermodified microstructure, but that of the added 60-80 ppm Sr had well modified structure of fine fibrous silicon. After solid solution treatment, the microstructure of the undermodified A356 alloy exhibited a partially spheroidized morphology, but the remainder showed the fragmentation of fibrous shaped silicon. The spheroidization of the eutectic silicon in the modified A356 alloys was completed during heat treatment, which was very effective in increasing the elongation. This is supported by the fracture surface in the tensile test.

• Journal of Korean Society of Water and Wastewater
• /
• v.23 no.4
• /
• pp.499-505
• /
• 2009

Many other countries have investigated the residual sludge treatment process to save the existing water resource and produce the high suspended solid concentration sludge. There are various methods for concentrating residual sludge, but the membrane system has received the most interest for its efficiency. The objective of this study was to evaluate the application of membrane filtration system for the residual sludge treatment. The experiment equipment was composed of Lab scale Crossflow tubular membrane filtration system. Generally, crossflow operation mode demands high electric cost mainly for the pump energy. So to cut off electric cost, very low Crossflow velocity was used in this experiment. Results confirmed that suspended solid concentration of residual sludge could be concentrated to 57,000mg/L in low Crossflow velocity tubular membrane system,. This concentration can be directly injected into the dehydrator. Based on the results, we know that the Crossflow tubular membrane system should be replaced conventional residual sludge treatment system.

• Journal of Magnetics
• /
• v.4 no.2
• /
• pp.46-51
• /
• 1999

A solid-HDDR characteristics of the Nd-Fe-B-type alloys magnetic properties of the solid-HDDR treated materials have been investigated using three types of alloys; $Nd_{15}Fe_{77}B_8 (alloy A), Nd_{16}Fe_{75.9}B_8Zr_{0.1}(alloy B), and Nd_{12.6}Fe_{68.7}Co_{11.6}B_8Ga_{1.0}Zr_{0.1} $(alloy C). It has been found that the four-components alloy B and six-components alloy C have showed higher hydrogenation temperatures than the ternary alloy A. The alloys A and B appeared to absorb more hydrogen gas more rapidly as well compared to the alloy C. The disproportionation temperature of hydrogenated materials was exhibited no significant difference among the alloys. The thermal stability of the hydrided materials of the three types of alloys was found to become more stable in order of number of components. The disproportionation and the recombination kinetics were significantly sluggish in the solid-HDDR manner with respect to the conventional manner. Some degree of anisotropic nature was found to exist in the ingot and this anisotropic nature was retained even after the solid-HDDR treatment. It was suggested the solid-HDDR treatment may possibly be used for a preparation of an isotropic or anisotropic Nd-Fe-B-type cast magnets.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.11
• /
• pp.1084-1088
• /
• 1995

A complete solid solution (SrLaAl1-xNixO4) between insulating SrLaAlO4 and metallic SrLaNi(Ⅲ)O4 oxides were prepared under high oxygen pressure (1.5 kbar, 800 ℃). They have tetragonal K2NiF4-type structure in all the solid solution range. Compared with lattice parameters of the same solid solution prepared under normal condition (1 bar, 1200 ℃), large decrease in the c-parameter was induced by high pressure treatment while no noticeable variation of the a-parameter was observed. Although marked changes of structural parameters, magnetic susceptibilities, and electron paramagnetic resonance spectra were consistently occurred before and after x=0.5, overall behaviors were essentially the same with those of solid solution prepared under normal condition. Such a phenomenon is explained by assuming the formation of partially filled narrow σ*x2-y2 band for x>0.5. Lattice contraction along the c-axis by high pressure treatment seems not to broaden this band. Particularly, the continuous absorption characteristic of a high free carrier concentration for x>0.5 and the absence of Ni-O in-plane stretching mode in the infrared absorption spectra supports this picture. However, the conductivities increasing with temperature for all solid solution suggest that some localization character, of probably Anderson type, remains for x>0.5.

• Journal of Biosystems Engineering
• /
• v.19 no.1
• /
• pp.3-8
• /
• 1994

An experiment on the expression and dewatering of chinese cabbage was conducted in order to investigate its dewatering behavior. Chopped cabbage was packed into cylinder and pressed by piston upto the predetermined pressure on Instron-1000. The rates of dewatering were affected domintantly by the applied pressure, but not significantly by the packed amount of cabbage in the cylinder. The pressure effect was increased very abruptly at first, but the increase rate was very low at high pressure greater than 20 MPa, showing great deviation from linear dependence of flow rate on pressure in Darcy's Law. Therefore, water expression from cabbage was not Newtonian flow of water through cell wall. In fact, the squeezed water contained a lot of solid particles, about 3% of solid cabbage particles, showing destruction of cell wall. It appeared that compression and dewatering of vegetable wastes in the low pressure. under 20 MPa, is more desirable for later treatment of the dewater. More researches are needed in order to develop a treatment method for the solid particles in the expressed water before an expeller treatment system can be applied to vegetable wastes.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc1
• /
• pp.110-113
• /
• 2012

Ge-S and Li-Ge-S powders were synthesized via solution-based process in order to employ chalcogenide-based solid electrolyte for use in Li secondary batteries. GeCl4 and thioacetamide in combination result in Ge-S powders of which major crystalline phase becomes GeS2 where the tetragonal and orthorhombic phases coexist after heat treatment. A chemical treatment using NaOH brings about the reduction of chlorine in the powders obtained. However, the heat treatment at 300 ℃ is more effective in minimizing the chlorine content. When lithium chloride is used as the precursor of Li ions, the LiCl powders are agglomerated with an inhomogeneous distribution. When Li2S is used, the Li-Ge-S powders are distributed more uniformly and the orthorhombic GeS2 phase dominates in the powders.