• Journal of the Korea Organic Resources Recycling Association
• /
• v.21 no.3
• /
• pp.74-81
• /
• 2013

In this study, the separation efficiency of wind power selector (the direction of the air flow of the air to perform gravity separation method) of municipal solid waste which was landfilled was investigated to reduce amount of waste that is designed to increase the recycling rate of wastes for the ANSYS CFX Program's numerical methods with wind through the separator. When a suction device designed to suction 1000mL of a plastic bag, the separation efficiency was 100% and when the wind speed was 0.9 m /sec or more and when the wind speed was 1.6 m / sec or more, the efficiency of plastic bottles in a mixture of 500mL and 1500mL plastic bottle waste was 100% and the aluminum screening efficiency of 250mL aluminum can was 100 % when the wind speed was 2.3 m / sec. In the last, 5mm thick compressed aluminum can efficiency was 90 % when the wind speed was 2.4 m / sec.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.187-190
• /
• 2009

A multiple pulse rocket motor distributes the thrust energy more effectively compared to typical rocket motor as providing subsequent thrusts by the pulse motors of the missile. The pulse rocket motor is the advanced technology to improve an end game capability of the missile by increasing the range and final velocity. A pulse separation device is the core part of the pulse motor. The pulse separation device of bulkhead type was designed and developed. The elastic-plastic structural analysis of the bulkhead and rupture disc was conducted. Several air tests were also conducted to confirm the structural safety and acceptability about the design concept. Test results were compared with the analysis results, which showed reasonable agreements.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.259-263
• /
• 2001

There are several steps such as slicing, lapping, chemical etching and mechanical polishing in the silicon wafer production process. The chemical etching step is necessary to remove damaged layer caused In the slicing and lapping steps. The typical etching liquor is the acid mixture comprising nitric acid, acetic acid and hydrofluoric acid. At present, the waste acid is treated by a neutralization method with a high alkali cost and balky solid residue. A solvent extraction method is applicable to separate and recover each acid. Acetic acid is first separated from the waste liquor using 2-ethlyhexyl alcohols as an extractant. Then, nitric acid is recovered using TBP(Tri-butyl phosphate) as an extractant. Finally hydrofluoric acid is separated with the TBP solvent extraction. The expected recovered acids in this process are 2㏖/l acetic acid, 6㏖/1 nitric acid and 6㏖/l hydrofluoric acid. The yields of this process are almost 100% for acetic acid and nitric acid. On the other hand, it is important to recover and reuse the metal values contained in various industrial wastes in a viewpoint of environmental preservation. Most of industrial products are made through the processes to separate impurities in raw materials, solid and liquid wastes being necessarily discharged as industrial wastes. Chemical methods such as solvent extraction, ion exchange and membrane, and physical methods such as heavy media separation, magnetic separation and electrostatic separation are considered as the methods for separation and recovery of the metal values from the wastes. Some examples of the application of solvent extraction to the treatment of wastes such as Ni-Co alloy scrap, Sm-Co alloy scrap, fly ash and flue dust, and liquid wastes such as plating solution, the rinse solution, etching solution and pickling solution are introduced.

• Journal of the Korean Geosynthetics Society
• /
• v.12 no.3
• /
• pp.87-94
• /
• 2013

As sediment contamination problems have recently been raised in Korea, the need for technologies to remove contaminants in sediments has increased. Contaminated sediments in Korea has been annually dredged and treated using processes of coagulation/flocculation, sedimentation on barges, dewatered and dried at prepared site, and then disposed at a landfill site, which is very costly, and only a limited landfill space available in Korea. Contaminants in media containing a high percentage of silt and clay sized particles, typically, are strongly adsorbed on the particles and difficult to remove. Particle separation processes that separate the fine clay and silt particles from the coarser sand and gravel and concentrate the contaminants into a smaller volume of sediment that can be further treated of disposed of, are very effective in the post step processes. In this study are to test the feasibility of treating dredged sediments using a hydrocyclone process, and to estimate design parameters for a pilot scale test. A hydrocyclone was operated to separate larger particles from the sediments. It was found that the particle separation was greatly affected by the solid contents and inlet pressure in the hydrocyclone.

• Environmental Engineering Research
• /
• v.18 no.2
• /
• pp.71-75
• /
• 2013

This study is to evaluate the effects of the separation wall on the sediment quality and quantity in a combined sewer, by surveying the sewer overflow and sediments during a rainfall. Since the separation wall installed in the combined sewer separates the rainfall and the sewage, the flow rate of the sewage is increased, and the amount of the sediment deposited on the sewer is decreased. One sampling point was the outfall of Daesacheon with a separation wall, and the other was the outfall of Gwaryecheon without a separation wall, in Daejeon metropolitan city. The maximum control of the biochemical oxygen demand (BOD) overflow load was more than 38% in the Daesacheon point with the separation wall, during a rainfall of 0.11 mm/hr. The maximum control of the BOD overflow load was 24% in Gwaryecheon without a separation wall, during a rainfall of 1.0 mm/hr. According to the survey results of the sediment in the sewer, the discharged sediment deposited on the sewer in Gwaryecheon point was about 23% to 28% of the total suspended solid during the rainfall. In addition, the average velocity of sewage in the presence of sediment was about 0.30 m/s, and if the separation wall is installed, it was expected to be about 1.01 m/s, that is 3.4 times more than the same conditions, resulting in the reduction of the sediment deposit.

• Journal of Animal Environmental Science
• /
• v.19 no.2
• /
• pp.177-182
• /
• 2013

We studied the possibility to produce solid fuel using cattle manure and to apply TAO (Thermophilic Aerobic Oxidation) process of solid-liquid separation fraction. The physiochemical compositions of cattle manure solid fuel chip were analyzed as water 0.12%, low calorific value 3,510 kcal/kg, ashes 11.9%, chlorine 0.82%, sulfur dust 0.5%, mercury non-detection, cadmium 1.0 mg/kg, lead 2 mg/kg, arsenic non-detection. In treating cattle manure with TAO reactor the internal temperature of the reactor was increasing higher and $50^{\circ}C$ and over was maintained after 20 hours on. The physiochemical compositions of liquids increased from pH 7.3 to pH 9.18 and EC decreased from 4.6 to 3.48 mS/cm in treating process of cattle manure with TAO reactor. COD and SCOD decreased from 16,800 to 10,400 mg/L, from 4,600 to 2,040 mg/L respectively, which showed about 38% and 56% of remove efficiency respectively.

• Tribology and Lubricants
• /
• v.37 no.2
• /
• pp.71-76
• /
• 2021

As opposed to using fossil fuels, we need to use eco-friendly resources such as sunlight, raindrops and wind to produce electricity and combat environmental pollution. A triboelectric nanogenerator (TENG) is a device that converts mechanical energy into electricity by inducing repetitive contact and separation of two dissimilar materials. During the contact and separation processes, electron flow occurs owing to a change in electric potential of the contacting surface caused by contact electrification and electrostatic induction mechanisms. A solid-solid contact TENG is widely known, but it is possible to generate electricity via liquid-solid contact. Therefore, by designing a hydrophobic TENG, we can gather electricity from raindrop energy in a feasible manner. To fabricate the superhydrophobic surface of TENGs, we employ a dip coating technique to synthesize an octadecylamine (ODA)- and polydimethylsiloxane (PDMS)-based coating on polyethylene terephthalate (PET). The synthesized coating exhibits superhydrophobicity with a contact angle greater than 150° and generates a current of 2.2 ㎂/L while water droplets fall onto it continuously. Hence, we prepare a box-type TENG, with the ODA/PDMS coating deposited on the inside, and place a 1.5 mL water droplet into it. Resultantly, we confirm that the induced vibration causes continuous impacts between the ODA/PDMS coating and the water, generating approximately 100 pA for each impact.

• Environmental Engineering Research
• /
• v.14 no.4
• /
• pp.262-269
• /
• 2009

This study examined the separation characteristics of particles in the rainfall runoff from paved roads using a ${\varphi}7.5$ cm hydrocyclone. The volume fraction and total suspended solids concentrations in the overflow and underflow from the hydrocyclone, as well as the separation efficiency were determined. The results indicated that the overflow volume increased with increasing operational pressure, but decreased with decreasing ratio of underflow outlet to inlet sizes ($D_u/D_i$), while the underflow to overflow volumes showed contrary behavior. The total suspended solid (TSS) concentration ratio between the overflow and inflow ($TSS_{over/in}$) decreased as a function of the operational pressure, while the corresponding ratio of underflow to inflow ($TSS_{under/in}$) increased. There was no visible difference in the $TSS_{over/in}$ with increasing $D_u/D_i$ ratio, but the $TSS_{under/in}$ decreased sharply. The particle removal efficiency was mainly affected by the particle size.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1996.10a
• /
• pp.75-76
• /
• 1996

다공성 고분자 분리막을 제조하는 방법으로 기존의 용매교환법을 대신하여 내용매성, 내약품성 및 내열성이 매우 뛰어난 고분자를 소재로하여 다공성 고분자막을 만드는 열유도 상분리법(Thermally Induced Phase Separation, TIPS)이 개발되었다. TIPS공정에서는 주로 고분자/희석제 system의 열역학적인 불안정성에 의하여 polymer-rich phase와 polymer-lean phase로 상이 분리되는 liquid-liquid phase separation과 결정성 고분자의 결정화에 의한 solid-liquid phase separation을 주로 상분리 mechanism으로 사용하고 있다. 따라서 위에 언급된 TIPS 이론에 근거한 melt spinning 공정에 의하여 PP 중공사막을 제조하였는데 wet spinning 공정에 의한 용매 교환법에 비해 비교적 공정이 단순하고 다공도를 조건하기가 용이하며 구조 및 성능면에서도 높은 재현성을 가지고 있다. 또한 우수한 소재임에도 불구하고 절절한 용매의 부재로 용매교환법에서 사용할 수 없었던 폴리올레핀계, 나일론계, 방향족출합계 고분자를 사용할 수 있게 되어 소재의 폭이 넓어졌다는데에 가장 큰 장점이 있다. 본 연구에서는 PP중공사막을 제조하기 위하여 먼저 용융 방사장치를 제작하였고 melt spinning 공정에 의해 막을 제조하는데 적합한 방사조건들을 확립한 후 결정된 방사조건에 의해 얻어진 PP 중공사막의 구조 및 성능에 영향을 미치는 인자들에 관하여 조사하였다.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1995.04a
• /
• pp.45-45
• /
• 1995

Filtration, one of the most important process in the various industrials, is defined as the separation of two or more compounds from a fluid by passing the mixture refers to the separation of solid, immisible particles from liquid or gaseous mixture. Membrane filtration which is a type of filtration extends it's application further to include the separation, concentration, and filtration. The main objective of this investigation is the preparation of organic solvents-resistant polyimide membranes by using phase inversion technique and their application as a UF membrane. Specially, the dope solution was prepared from the newly developed method. The newly developed method is that the dope solution was directly prepared from the polyimide solution which was prepared by the modified one-step polymerization. The effects of the parameters for membrane preparation such as the casting solution composition and the casting conditions were investigated and the performance and chemical stabfiity of membrane are going to be tested.