• KEPCO Journal on Electric Power and Energy
• /
• v.7 no.1
• /
• pp.161-165
• /
• 2021

In general, SOFCs mainly use Ni-YSZ cermet, a mixture of Ni and YSZ, as an anode material, which is stable in a high-temperature reducing atmosphere. However, when SOFCs have operated at a high temperature for a long time, the structural change of Ni occurs and it results in the problem of reducing durability and efficiency. Accordingly, a development of a new anode material that can replace existing nickel and exhibits similar performance is in progress. In this study, SrTiO₃, which is a perovskite-based mixed conductor and one of the candidate materials, was used. In order to increase the electrical conduction properties, Y_0.08Sr_0.92Fe_0.3Ti_0.7O₃, doped with 0.08 mol of Y³⁺ in Sr-site and 0.03 mol of transition metal Fe³⁺ in Ti-site, was synthesized and its chemical diffusion coefficient and reaction constant were measured. Its electrical conductivity changes were also observed while changing the oxygen partial pressure at a constant temperature. The performance as a candidate electrode material was verified by predicting the defect area through the electrical conductivity pattern according to the oxygen partial pressure.

• Journal of the Korean Ceramic Society
• /
• v.49 no.2
• /
• pp.197-203
• /
• 2012

In this study, in order to improve densification of $La_{0.8}Ca_{0.2}Cr_{0.9}Co_{0.1}O_{3-\delta}$ (LCCC), which is known for one of the most proper candidate interconnector materials in the solid oxide fuel cells, $CaCrO_4$ was prepared via solid oxide synthesis route and added to the LCCC with different amount and particle sizes. As the amount of the $CaCrO_4$ increased, porosity of the sintered samples increased, and the pore size was proportional to the particle size of the $CaCrO_4$. This supports the fact that the $CaCrO_4$ phase forms liquid during sintering and permeate into the matrix leaving behind large pores. Then the liquid reacts with the matrix through the solid solution. However, when the samples were sintered with a slow ramp up rates, the porosity decreased. This is thought to be caused by the progressive solid solution of $CaCrO_4$ before the temperature reach to the melting temperature and forms a fluent amount of liquids. The sintering behavior of the LCCC with the addition of $CaCrO_4$ was analyzed through the transient liquid phase sintering on the basis of the microstructure observation and phase identification by x-ray diffraction.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.1
• /
• pp.1-12
• /
• 2016

In this study, CFD model for a Heat Exchange Steam Reformer (HESR) used for a 10kW SOFC system is developed for the design optimization of the HESR. The model is used to explore the effect of design parameters on the performance of the HESR. In the HESR, heat is delivered from the hot gas channel to the fuel channel to supply the heat required for the fuel reforming. In the fuel channel where the fuel is reformed, thermo-fluid dynamics, heat transfer, and chemical reaction are considered to predict the performance of the reformer. The model is validated with experimental data within 2~3% error. The validated model is used for the parametric study of the HESR design. Channel length, channel diameter, and flow direction are selected as the design parameters. The effects of the HESR design parameters on the outlet temperature, outlet H2 mole fraction, and pressure drop across the reformer are presented using the model.

• Journal of the Korean Ceramic Society
• /
• v.39 no.4
• /
• pp.346-351
• /
• 2002

The electrical conductivity and phase stability of $ZrO_2$ doped with $Sc_2O_3$ and $CeO_2$ were investigated in order to search for better solid electrolyte material for solid oxide fuel cell. Present study showed that $ZrO_2$ doped with $Sc_2O_3$ and $CeO_2$ exhibited no phase transition during the heat treatment up to $1350^{Circ}C∼1550^{Circ}C$ and was stable as a cubic phase in whole temperature ranges. The $ZrO_2$ doped with $Sc_2O_3$ and $CeO_2$ showed much higher electrical conductivity than YSZ in the temperature range of $300∼^{Circ}C$ and better long term stability than other sc-$ZrO_2$ based electrolyte that showed the possibility as a strong candidate electrolyte material for intermediate-or low-temperature SOFC.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.241.1-241.1
• /
• 2011

Numerous possible applications for $ZrO_2$ nanotubes exist such as for catalyst support structures, for sensing or for applications as a solid state electrolyte. Especially, because of a large specific surface area, high efficiency for solid oxide fuel cell (SOFC) application at low temperature can be expected for nanotublar structures in even small size. A zirconium precursor, Tetrakis (ethylmethylamino) zirconium, TEMAZr and $H_2O$ oxidant were used to deposit$ZrO_2$ thin films on an anodized aluminum oxide (AAO) templates having sub-100nm cylindrical pores by atomic layer deposition (ALD) in the temperature range of 150~250$^{\circ}C$. The crystalline structures of as-prepared and post-annealed $ZrO_2$ nanotubes were characterized by x-ray diffraction and high-resolution transmission electron microscopy. The as-prepared samples at $150^{\circ}C$ and $200^{\circ}C$ were showed amorphous, whereas a mixed phase of tetragonal, monoclinic and amorphous polymorph was observed at $250^{\circ}C$. In the bulk, zirconia remains monoclinic phase up to $1,175^{\circ}C$, however, $ZrO_2$ nanotubes were showed tetragonal phase upon post thermal treatments merely at $400^{\circ}C$. This trend may be indicative of high-curvature surfaces of nanotubes and thereby the presence of intrinsic compressive strain. The amount of amorphous structures in the mixed phase as well as as-grown $ZrO_2$ nanotubes were also gradually decreased by subsequent heat treatment.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.1
• /
• pp.41-47
• /
• 2003

For the development of low temperature anode-supported planar solid oxide fuel cell, the planar anode supports with the thickness of 0.8 to 1 mm and the area of 25, 100 and $150\;cm^2$ were fabricated by the tape casting method. The strength, porosity, gas permeability and electrical conductivity of the planar anode support were measured. The porosity of anode supports sintered at $1400^{\circ}C$ and then reduced in$H_2$ atmosphere was increased from $45.8\%\;to\;53.9\%$. The electrical conductivity of the anode support was $900 S/cm\;at\; 850^{\circ}C$ and its gas permeability was 6l/min at 1 atm in air atmosphere. The electrolyte layer and cathode layer were fabricated by slurry dip coating method and then had examined the thickness of $10{\mu}m$ and the gas permeability of 2.5 ml/min at 3 atm in air atmosphere. As preliminary experiment, cathode multi-layered structure consists of LSM-YSZ/LSM/LSCF. At single cell test using the electrolyte layer with thickness of 20 to $30{\mu}m$, we achieved $300\;mA/cm^2$ and 0.6V at $750^{\circ}C$

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.196-199
• /
• 2007

The chemical states of oxygen on the surfaces of $Pr_{1-x}Sr_{x}CoO_{3}$ (x=0.5 and 0.7) oxide systems were investigated by X-ray photoelectron spectroscopy. Merged oxygen peaks of $Pr_{1-x}Sr_{x}CoO_{3}$ (x=0.5 and 0.7) oxides could be divided as five sub-peaks. These five sub-peaks could be defined as lattice oxygen ($O_{L}$). chemisorbed oxygen peaks ($O_{C}$) and hydroxyl condition oxygen peak ($O_{H}$). In case of the $Pr_{0.5}Sr_{0.5}CoO_{3}$ and $Pr_{0.3}Sr_{0.7}CoO_{3}$, the binding energy (BE) of oxygen lattice were located at same BE. However, the BE of chemisorbed oxygen peaks including oxygen vacancy shows different BE. Especially, it was found that BE of chemisorbed oxygen peaks was increased when more Sr were substituted. Comparing atomic percentages of oxygens of $Pr_{0.5}Sr_{0.5}CoO_{3}$ and $Pr_{0.3}Sr_{0.7}CoO_{3}$, the ratio of $Pr_{0.3}Sr_{0.7}CoO_{3}$ was higher than that of $Pr_{0.5}Sr_{0.5}CoO_{3}$. It showed more chemically adsorbed site including oxygen vacancies were existed in $Pr_{0.3}Sr_{0.7}CoO_{3}$.

• Journal of the Korean Ceramic Society
• /
• v.29 no.11
• /
• pp.900-904
• /
• 1992

High temperature electrical conductivity was measured for perovskite La0.98Sr0.02MnO3 at 200~130$0^{\circ}C$ as a function of Po2 and 1/T. Perovskite La1-xSrxMnO3 system is the typical oxygen electrode in solid oxide fuel cell (SOFC). Acetate precursors were used for the preparation of mixed water solution and the calcined powders were reacted with Na2CO3 flux in order to obtain highly reactive powders of perovskite La0.98Sr0.02MnO3. The relative density was greatly increased above 90% because of the homogeneous sintering. From the conductivity ($\sigma$)-temperature and conductivity-Po2 at constant temperature, the defect structure of La0.98Sr0.02MnO3 was discussed. From the slope of 1n($\sigma$) vs 1/T, the activation energy of 0.069 and 0.108eV were evaluated for above 40$0^{\circ}C$, respectively. From the relationship between $\sigma$ and Po2, it was found that the decomposition of La0.98Sr0.02MnO3 was occurred at 10-15.5 atm(97$0^{\circ}C$) and 10-11 atm(125$0^{\circ}C$). It is supposed that the improvement of p-type conductivity may be leaded by the increase of Mn4+ concentration through the substitution of divalent/monovalent cations for La site in LaMnO3.

• Journal of the Korean Ceramic Society
• /
• v.47 no.2
• /
• pp.195-198
• /
• 2010

It has been considered to apply GDC ($Gd_{0.1}Ce_{0.9}O_{1-X}$) for low-temperature SOFC electrolytes because it has higher ionic conductivity than YSZ at low temperature. However, open circuit voltage with using GDC ($Gd_{0.1}Ce_{0.9}O_{1-X}$) electrolyte in SOFCs, becomes lower than using YSZ (8 mol% Yttria stabilized Zirconia) electrolyte because GDC has electronic conductivity. In this work, the effect of changing GDC electrolyte thickness on the open circuit voltage has been investigated. Ni-GDC anode-supported unit cells were fabricated as follows. Mixed NiO-GDC powders were pressed and pre-sintered at $1200^{\circ}C$. And then, GDC electrolyte material was dip-coated on the anode and sintered at $1400^{\circ}C$. Finally the LSCF-GDC cathode material was screen-printed on the electrolyte and sintered at $1000^{\circ}C$. Electrolyte thickness was controlled by the number of dip-coating times. Open circuit voltage was measured depending on electrolyte thickness at $650^{\circ}C$ and found that the thicker GDC electrolyte was, the better OCV was.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.162-162
• /
• 2008

세리아는 고체 산화물 연료전지(SOFC, solid oxide fuel cell)의 전해질 재료와CMP( chemical mechanical polishing) 슬러리 재료, 자동차의 3원 촉매, gas sensor, UV absorbent등 여러 분야에서 사용되고 있다. 본 연구에서는 세리아의 입자의 크기와 형상을 조절하여 성능 및 물성을 향상시켜 보다 넓은 분야의 활용을 하고자 실험을 실시하였다. 세리아 합성에 사용되는 전구체인 cerium carbonate의 특성이 세리아 분말의 물리화학적 특성에 직접적인 영향을 주기 때문에 전구체의 합성 단계에서 형상과 크기를 조절하고자 하였다. 세륨염으로 cerium nitrate hexahydrate, 균일침전반응을 할 수 있는 urea를 침전제로 사용하였다. 반응 용매의 유전상수를 조절하고 반응의 과포화도 변화를 이용하기 위하여 에탄올을 첨가하여 입자의 크기 및 형상을 조절, cubic형태의 $Ce_2O(CO_3)_2{\cdot}H_2O$ 결정상을 가지는 세리아 전구체를 합성하였다. 이렇게 생성된 전구체를 $1000^{\circ}C$에서 2시간동안 하소하여 세리아를 합성하고 반응시간, 농도, 에탄올의 함량 변화에 대해 XRD, FE-SEM, particle size analyzer, micropore physisorption analyzer 분석을 통하여 입자의 결정상과 형상, 입도 분포 및 기공분포 등을 반응인자의 변화에 따라 비교 및 해석하였다.