• The Bulletin of The Korean Astronomical Society
• /
• v.19
• /
• pp.19.1-19.1
• /
• 1994

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.6
• /
• pp.401-405
• /
• 2017

Because silicon thin film solar cells have a high absorption coefficient in visible light, they can absorb 90% of the solar spectrum in a $1-{\mu}m$-thick layer. Silicon thin film solar cells also have high transparency and are lightweight. Therefore, they can be used for building integrated photovoltaic (BIPV) systems. However, the contact electrode needs to be replaced for fabricating silicon thin film solar cells in BIPV systems, because most of the silicon thin film solar cells use metal electrodes that have a high reflectivity and low transmittance. In this study, we replace the conventional aluminum top electrode with a transparent aluminum-doped zinc oxide (AZO) electrode, the band level of which matches well with that of the intrinsic layer of the silicon thin film solar cell and has high transmittance. We show that the AZO effectively replaces the top metal electrode and the bottom fluorine-doped tin oxide (FTO) substrate without a noticeable degradation of the photovoltaic characteristics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.469.2-469.2
• /
• 2014

All-solid-state solar cell based on Chloride doped organometallic halide perovskite, (CH3NH3)PbIxCl3-x, has achieved a highly power conversion efficiency (PCE) to over 15% [1] and further improvements are expected up to 20% [2]. In this way, solar cells using novel light absorbing perovskite material are actively being studied as a next generation solar cells. However, making solution-process require high temperature up to $500^{\circ}C$ to form compact hole blocking layer and sinter the mesoporous oxide scaffold layer. Because of this high temperature process, fabrication of flexible solar cells on plastic substrate is still troubleshooting. In this study, we fabricated highly efficient flexible perovskite solar cells with PCE in excess of 11%. Atomic layer deposition (ALD) is used to deposit dense $TiO_2$ as hole blocking layer on ITO/PEN substrate. The all fabrication process is done at low temperature below $150^{\circ}C$. This work shows that one of the important blueprint for commercial use of perovskite solar cells.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.14 no.4 s.36
• /
• pp.281-291
• /
• 1990

Experiment I and II had done to develop the solar heat proof hat for field work in the summer. In the experiment I physical characteristics of several fabrics was tested to determine which one Is proper to make the solar heat proof hat. On the base of above results in the experiment II three improved solar heat proof hat was deviced and tested solar heat proof effect and compared the existing summer working hat by wearing trials in the environmental chamber. The results obtained were as follows. 1. In the view of the physical characteristics of six fabrics (Blue T/C, White poplin, Vapor transfer silver coating nylon taffeta, No vapor trans(or silver coating nylon taffeta, Aluminum coating T/C, Microporous fabric), the light color T/C and no vapor transfer silver coating nylon ta(feta is proper to make improved solar heat proof working hat. 2. Three improved hats that are made of white T/C, grey T/C and no vapor transfer silver coating nylon taffeta have more solar heat proof effect than the existing summer working hat. 3. Among the three improved hats, the improved hat that is made of no vapor transfer silver coating nylon taffeta is most effective to proof the solar heat.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.3
• /
• pp.365-370
• /
• 2013

Generally, photovoltaic modules consist of glass, EVA, Solar Cell, back sheet and ribbon. But EVA, solar cell, ribbon affect electric output with temperature. EVA is a change in the transmittance of light from the sun. In addition, the solar cell output is decreased with temperature and the ribbon increases resistance. Transmittance and reflectance of glass and EVA were measured. In this paper, the characteristics of the components of PV module as EVA and Glass, ribbon were studied by variable temperature. effects on material properties investigated. As a result, glass is independent in temperature variation. EVA was the reduction 1~4% in transmittance. Solar cell decrease 0.469[%/$^{\circ}C$] in electric output by temperature variation. Other factors was controlled in solar cell..

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.221-221
• /
• 2012

Small-molecule organic photovoltaic cells have recently attracted growing attention due to their potential for the low-cost fabrication of flexible and lightweight solar modules. The PVP/Ag nanoparticles were synthesized by the reaction of poly vinylpyrrolidone (PVP) and silver nitrate at $150^{\circ}C$. In the reaction, the size of the nanoparticles was controlled by relative mole fractions between PVP and Ag. The PVP/Ag nanoparticles with various sizes were then spin coated on the patterned ITO glass prior to the deposition of the PEDOT:PSS hole transport layer. The scattering of the incident light caused by these incorporated nanoparticles resulted in an increase in the path length of the light through the active layer and hence the enhancement of the light absorption. This scattering effect increased as the size of the nanoparticles increased, but it was offset by the decrease in total transmittance caused by the non-transparent nanoparticles. As a result, the maximum power conversion efficiency, 0.96% which was the value enhanced by 14% compared to the cell without incorporation of nanoparticles, was obtained when the mole fraction of PVP:Ag was 24:1 and the size of the nanoparticles was 20~40 nm.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.5
• /
• pp.583-591
• /
• 2007

This paper reports the performance of a 150W PV-wave hybrid system with battery storage in buoy. This system was originally designed to meet a new hybrid ower system for buoy in Korea. In the case or lighted buoys and lighthouses, a light failure alarm system of wireless radio is attached so that light failures are immediately notified to the office. At lighthouse offshore fixed lights and light buoys where commercial electricity is not available, the power source depends on solar system and batteries. This power system has a various problems. Therefore energy derived from the sunshine, wind and waves has been used as the energy source lot aids to navigation. Recently a hybrid system of combining the solar, wind and the wave generator is a favorable system lot the ocean facilities like lighthouse and buoy. The hybrid system in this paper is intended for variable DC load like light, communication system in the buoy and includes a PV-wane generation system and battery. This is composed a high efficiency charging algorithm, switching converter and controller. This paper includes discussion on system reliability, power quality, and effects of hybrid system in the buoy. Simulation and experimental results show excellent performance.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.2
• /
• pp.113-119
• /
• 2011

LED lighting has received much attention in recent years due to its high energy efficiency and environmental friendliness. As the color of light can be obtained by adjusting the light intensity of LEDs, the quality of visual environment can be improved. The aims of this study are to develop a wavelength adjustable LED lighting system and to examine its lighting performances. The LED lighting system and experimental cell for assessment of the lighting performance were constructed. This LED lighting system is able to materialize the various spectral power distribution and color temperature of light through the control of the four dimmers. Up to $432^4$ kinds of light combinations are possible. The range of illuminance on workplane were measured as 7~1,831 ㏓. Improvement of psychological and physical functions for occupants can be expected according to control of lighting performances.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.3
• /
• pp.66-74
• /
• 2014

In this paper, the performance of Hybrid Dimming control system for Daylighting system is evaluated by accredited tests. The system controls the balance of illuminance of daylight between daylight system and LED light system. It makes the normal illuminance of interior without the effects of weather by controlling the LED depending on the brightness of outside. For the tests, 6 diffusers($600{\times}300mm$) were installed in lighting area($36m^2$) and normal operation of the system sensors were tested about the interference of sunlight. The results of the examinations were satisfied with the criteria of accredited tests. Further research is the verification of energy saving effect by comparing the Hybrid Dimming control system to current artificial light system.

• Current Photovoltaic Research
• /
• v.7 no.2
• /
• pp.33-37
• /
• 2019

In this paper, we compared the performance of $Cu(In,Ga)(S,Se)_2$ (CIGSSe) thin film solar cell with CdS buffer layer deposited by irradiating 365 nm UV light with 8 W power in Chemcial Bath Deposition (CBD) process. The effects of UV light irradiation on the thin film deposition mechanism during CBD-CdS thin film deposition were investigated through chemical and electro-optical studies. If the UV light is irradiated during the solution process, the hydrolysis of Thiourea is promoted even during the same time, thereby inhibiting the formation of the intermediate products developed in the reaction pathway and decreasing the pH of the solution. As a result, it is suggested that the efficiency of the CdS/CIGSSe solar cell is increased because the ratio of the S element in the CdS thin film increases and the proportion of the O element decreases. This is a very simple and effective approach to control the S/O ratio of the CdS thin film by the CBD process without artificially controlling the process temperature, solution pH or concentration.