• Current Industrial and Technological Trends in Aerospace
• /
• v.8 no.2
• /
• pp.24-30
• /
• 2010

Space solar sails are a form of spacecraft propulsion using the radiation pressure of light from a star or laser to push enormous ultra-thin mirrors to high speeds. With respect to it, U.S.A, Japan, E.U. and Russia, etc. have performed a substantial research and the space flight test. On May 2010, JAXA succeeded in launching the world's first interplanetary solar sail spacecraft "IKAROS" to Venus. Currently, solar sail propulsion is aimed chiefly at accomplishing a number of non-crewed missions in any part of the solar system and beyond. This paper presents the technology trend of advanced countries on the development of the solar sails as a new propulsion method for the space investigation and travel.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.4
• /
• pp.513-517
• /
• 2007

To elucidate possible challenges for outdoor practical use of dye-sensitized solar cells (DSCs), we compared conventional Si solar cells with DSCs. DSC modules still require a larger area than conventional Si solar modules to attain the same rated output because of lower photoelectron-chemical conversion efficiency. However, in backup systems by using batteries, the measured data shows that DSCs generated 15% more electricity than Si solar cells of the same rated output power in the same interval of cloudy daylight. Moreover, the battery charging time of DSCs is about 1 hour faster than the same rate of Si solar cells under outdoor cloudy daylight. This result also indicates that conversion efficiency obtained by the certified condition less than AM 1.5 condition does not always coincide with the electricity generated outdoors daily, and it is not a crucial measure to evaluate the performance of solar cells.

• Current Photovoltaic Research
• /
• v.11 no.1
• /
• pp.18-26
• /
• 2023

Tin perovskite solar cells have attracted a lot of attention due to their potential to address the toxicity of lead, which is the biggest barrier to commercialization of perovskite solar cells. Unlike other lead-free perovskite, tin perovskite have a direct bandgap, which is suitable for use as light harvesting, and relatively good stability, which has led to a lot of attention. Since the first tin perovskite solar cell was reported in 2014, it has achieved an impressive power conversion efficiency of 14.81%. However, this efficiency is still low compared to that of lead perovskite solar cells, and the stability of tin perovskite solar cells is also an issue that needs to be addressed. In this review, we will discuss the basic properties of the tin atom in comparison to the lead atom, and then discuss the crystal structure, phase transition, and basic properties of tin perovskite. We will then discuss the advantages, applications, challenges, and strategies of tin perovskite, In particular, we will focus on how to prevent the oxidation of tin, which is arguably the biggest challenge for using tin perovskite solar cells. At the end, we summarize the key factors that need to be addressed for higher efficiency and stability, emphasizing what is needed to commercialize tin perovskite solar cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.86-86
• /
• 2012

The new approaches for silicon solar cell of new concept have been actively conducted. Especially, solar cells with wire array structured radial p-n junctions has attracted considerable attention due to the unique advantages of orthogonalizing the direction of light absorption and charge separation while allowing for improved light scattering and trapping. One-dimenstional semiconductor nano/micro structures should be fabricated for radial p-n junction solar cell. Most of silicon wire and/or pillar arrays have been fabricated by vapour-liquid-solid (VLS) growth because of its simple and cheap process. In the case of the VLS method has some weak points, that is, the incorporation of heavy metal catalysts into the growing silicon wire, the high temperature procedure. We have tried new approaches; one is electrochemical etching, the other is noble metal catalytic etching method to overcome those problems. In this talk, the silicon pillar formation will be characterized by investigating the parameters of the electrochemical etching process such as HF concentration ratio of electrolyte, current density, back contact material, temperature of the solution, and large pre-pattern size and pitch. In the noble metal catalytic etching processes, the effect of solution composition and thickness of metal catalyst on the etching rate and morphologies of silicon was investigated. Finally, radial p-n junction wire arrays were fabricated by spin on doping (phosphor), starting from chemical etched p-Si wire arrays. In/Ga eutectic metal was used for contact metal. The energy conversion efficiency of radial p-n junction solar cell is discussed.

• Current Photovoltaic Research
• /
• v.5 no.1
• /
• pp.20-24
• /
• 2017

Recently, three-dimensional (3D) light harvesting structures are highly attracted because of their high light harvesting capacity and charge collection efficiencies. In this study, we have fabricated $Cu_2ZnSn(S_xSe_{1-x})_4$ based 3D thin film solar cells on PR patterned Molybdenum (Mo) substrates using photolithography technique. Specifically, Mo patterns were deposited on PR patterned Mo substrates by sputtering and the thin Cu-Zn-Sn stacked layer was deposited over this Mo patterns by sputtering technique. The stacked Zn-Sn-Cu precursor thin films were sulfo-selenized to form CZTSSe pattern. Finally, CZTSSe absorbers were coated with thin CdS layer using chemical bath deposition and ZnO window layer was deposited over CZTSSe/CdS using DC sputtering technique. Fabricated 3-D solar cells were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF) analysis, Field-emission scanning electron microscopy (FE-SEM) to study their structural, compositional and morphological properties, respectively. The 3% efficiency is achieved for this kind of solar cell. Further efforts will be carried out to improve the performance of solar cell through various optimizations.

• KIEAE Journal
• /
• v.2 no.1
• /
• pp.49-54
• /
• 2002

Solar daylighting system provides free and comfort lighting, but its cost has been key issue due to difficult design and control of the heavy light collecting system. One of the solutions for the heavy design issues would be using a light framed film such fresnel and prism lens. Prism light guide luminaires have for some time been used to distribute light when it is desirable to have remote light sources. These systems are helpful when it is desirable to have fewer light sources, and/or to position light sources in places where lamp maintenance is easier, or electrical hazard is reduced. This proposed prototype system consists of light collector, light transformer and light pipe.

• Journal of Bio-Environment Control
• /
• v.5 no.1
• /
• pp.57-64
• /
• 1996

To use effectively the solar energy in greenhouse heating, a high performance solar collector should be developed. And then the size of the solar collector and thermal storage tank should be determined through the calculation of heating load. The solar collector must be set in the optimum tilt angle and direction to take daily solar radiation maximally, and the flow rate of heat transfer fluid through the solar collector should be kept in the optimum range. In this research, the performance tests of a capillary tube solar collector were performed to determine the optimum water flow rate and the results summarized as follows. 1. The regressive equations for efficiency estimations of the capillary tube solar collector in the open loop were modeled in the water flow rate of 700-l,000 $\ell$/hr. 2. The optimum water flow rate of the solar collector was estimated by the second order polynomial regression and the maximum efficiency was 80% at the water flow rate of 850 $\ell$/hr. 3. The solar thermal storage system consisted of a capillary tube solar collector and a water storage tank was tested at the water flow rate of 850 $\ell$/hr in the closed loop, and obtained the solar thermal storage efficiency of 55.2%. 4. As the capillary tube solar collector engaged in this experiment was made of non-corrosive polyolefin tubes, its weight was as light as 1/30 of the flat plate solar collector made of copper tubes. Therefore it was considered to be suitable for the greenhouse heating system.

• ETRI Journal
• /
• v.26 no.6
• /
• pp.647-652
• /
• 2004

A new ionic liquid, 1-vinyl-3-heptylimidazolium iodide (VHpII), was synthesized and applied as a redox electrolyte for dye-sensitized solar cells. The chemical structure of the synthesized VHpII was confirmed using $^1H$ NMR. Thermogravimetric analysis showed that the VHpII was stable for thermal stress of up to $250^{\circ}C$. The energy conversion efficiencies of the VHpII-based dye-sensitized solar cells were investigated in terms of the effect of a lithium iodide addition. A solar cell containing the redox couple of VHpII and iodine showed a conversion efficiency of 2.63% under 1 sun light intensity at AM 1.5. Adding 0.4 M LiI results in a conversion efficiency of 3.63%, which was an improvement of about 40%. The increased conversion efficiency was ascribed to an increase in external quantum efficiency.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.spc3
• /
• pp.262-268
• /
• 2012

In the recent research technical solutions have been studied to integrate renewable energy into unmanned aerial vehicles to use it as the main power source. As the weight of the aerial vehicle body is essential for its performance, we consider to use light-weight solar cell technology. Furthermore fuel cells are also integrated create a highly energy-efficient aerial robot. In this paper, construction concept and software design of the tilt-rotor aerial vehicle GAORI is introduced which uses solar cells and fuel cells as power source. The future work direction and prognosis are discussed.

• The Bulletin of The Korean Astronomical Society
• /
• v.40 no.1
• /
• pp.63.2-63.2
• /
• 2015

Solar flare is one of the energetic phenomena observed on the Sun, and it is often accompanied with eruptions such as global-scale eruption of a flux rope (filament/prominence eruption) and small-scale eruption of a plasmoid. A flare itself is a dissipative phenomenon where accumulated electric current representing free magnetic energy is dissipated quickly at a special location called a current sheet formed in a generally highly conductive solar corona. Previous studies have demonstrated how a solar magnetic field placed on the Sun forms a current sheet when magnetic shear is added to the field. Our study is focused on a self-consistent process of how a subsurface magnetic field emerges into the solar atmosphere and forms a current sheet in the corona. This study also gives light to a relation among a flare and two types of flare-associated eruptions; flux-rope eruption and plasmoid eruption.