• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 춘계학술발표대회 논문집
• /
• pp.105-110
• /
• 2011

The doping procedure in crystalline silicon solar cell fabrication usually contains oxygen injection during drive-in process and removal of phosphorous silicate glass(PSG). In this paper, we studied the effect of oxygen injection and PSG on conversion efficiency of solar cell. The mono crystalline silicon wafers with $156{\times}156mm^2$, $200{\mu}m$, $0.5-3.0{\Omega}{\cdot}cm$ and p-type were used. After etching $7{\mu}m$ of the surface to form the pyramidal structure, the P(phosphorous) was injected into silicon wafer using diffusion furnace to make the emitter layer. After then, the silicon nitride was deposited by the PECVD with 80 nm thickness and 2.1 refractive index. The silver and aluminium electrodes for front and back sheet, respectively, were formed by screen-printing method, followed by firing in 400-425-450-550-$880^{\circ}C$ five-zone temperature conditions to make the ohmic contact. Solar cells with four different types were fabricated with/without oxygen injection and PSG removal. Solar cell that injected oxygen during the drive-in process and removed PSG after doping process showed the 17.9 % conversion efficiency which is best in this study. This solar cells showed $35.5mA/cm^2$ of the current density, 632 mV of the open circuit voltage and 79.5 % of the fill factor.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.169-172
• /
• 2004

The effect of the process parameters on the stable lifetime in rapid thermal firing(RTF) was investigated in order to optimize the process for the Cz-silicon. The process temperature was varied between $700^{\circ}C\;and\;950^{\circ}C$ while the process time was chosen 1 s and 10 s. At below $850^{\circ}C$ the stable lifetime for 10 s is higher than that for 1 s and increases with increasing by the process temperature. However, at over $850^{\circ}C$ the improved stable lifetime is not dependent on the process time and temperature. On the other hand, two high temperature processes in solar cell fabrics are combined with the optimized process and the non-optimized process. The last process determines the stable lifetime. Also, the degraded stable lifetime could be increased by processing in optimized process. The decreased lifetime can increase using the optimized oxidation process, which is a final process in solar cells. Finally, the optimized and non-optimized processes are applied solar cells.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.43.2-43.2
• /
• 2010

In this study, metallurgical grade (MG) silicon with 99% purity produced by arc furnace process was systematically investigated for slag refining. The most problematic impurities to remove from MG silicon are boron (B) and phosphorus (P). To remove B and P from MG-silicon, we used synthetic slag in the molten state. MG-silicon with synthetic slag of CaO, $SiO_2$, and $CaF_2$ was melted using by high-frequency induction furnace with electrical output of 50kW. Specimens prepared by various refining process conditions(holding time, mixture ratio) were inspected by combined analysis of ICP-MS and XRF. With this approach, B has been reduced to <5ppm, P to <1ppm and other impurities to 0.1~0.2% except for Calcium. Calcium has been increased from 17ppm to 1500ppm. Problem of calcium contamination will be resolved by additional refining processes.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.405-405
• /
• 2011

실리콘 질화막(SiNx : H)는 결정질 실리콘 태양전지 제작 공정에서 ARC (Anti Reflection Coating)과 표면 패시베이션의 역할로써 많이 사용되었지만, layer 자체의 quality가 좋지 않기 때문에 최근에는 SiNx/SiO2 이중 layer로 passivation layer를 형성하고 있다. SiO2 layer는 Si substrate를 소스로 하여 성장시키기 때문에 막의 질이 우수하기는 하지만, 막 성장을 위해서 Furnace를 이용해야 하기 때문에, 공정 시간과 공정 비용을 증가시키는 단점이 있다. 본 연구에서는 SiO2 layer를 Furnace가 아닌, 질산(HNO3)을 이용하여SiNx/Thin SiO2 passivation layer 제작하였다. 실험에서는 SiO2 성장을 위해서 질산 용액에 p-type wafer를 dipping하여 시간대 별, SiO2 막의 두께를 관찰하였고, passivation의 효과를 확인하기 위해 lifetime을 측정하였다. 그 결과 SiNx/SiO2 이중 passivation layer는 SiNx 단일 막으로 passivation을 하였을 때보다, lifetime이 10 us 상승했고, 셀 제작시 효율은 약 1.1%, Fill Factor는 약 4% 정도 증가한 것을 확인할 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.86.2-86.2
• /
• 2015

Cu2ZnSn(S,Se)4 thin film solar cells have been fabricated using sputtered Cu/Sn/Zn metallic precursors on Mo coated sodalime glass substrate without using a toxic H2Se and H2S atmosphere. Cu/Sn/Zn metallic precursors with various thicknesses were prepared using DC magnetron sputtering process at room temperature. As-deposited metallic precursors were sulfo-selenized inside a graphite box containing S and Se pellets using rapid thermal processing furnace at various sulfur to selenium (S/Se) compositional ratio. Thin film solar cells were fabricated after sulfo-selenization process using a 65 nm CdS buffer, a 40 nm intrinsic ZnO, a 400 nm Al doped ZnO, and Al/Ni top metal contact. Effects of sulfur to selenium (S/Se) compositional ratio on the microstructure, crystallinity, electrical properties, and cell efficiencies have been studied using X-ray diffraction, Raman spectroscopy, field emission scanning electron microscope, I-V measurement system, solar simulator, quantum efficiency measurement system, and time resolved photoluminescence spectrometer. Our fabricated Cu2ZnSn(S,Se)4 thin film solar cell shows the best conversion efficiency of 9.24 % (Voc : 454.6 mV, Jsc : 32.14 mA/cm2, FF : 63.29 %, and active area : 0.433 cm2), which is the highest efficiency among Cu2ZnSn(S,Se)4 thin film solar cells prepared using sputter deposited metallic precursors and without using a toxic H2Se gas. Details about other experimental results will be discussed during the presentation.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.250-253
• /
• 2007

An evaporated Ti/Pd/Ag contact system is most widely used to make high-efficiency silicon solar cells, however, the system is not cost effective due to expensive materials and vacuum techniques. Commercial solar cells with screen-printed contacts formed by using Ag paste suffer from a low fill factor and a high shading loss because of high contact resistance and low aspect ratio. Low-cost Ni and Cu metal contacts have been formed by using electroless plating and electroplating techniques to replace the Ti/Pd/Ag and screen-printed Ag contacts. Ni/Cu alloy is plated on a silicon substrate by electro-deposition of the alloy from an acetate electrolyte solution, and nickel-silicide formation at the interface between the silicon and the nickel enhances stability and reduces the contact resistance. It was, therefore, found that nickel-silicide was suitable for high-efficiency solar cell applications. The Ni contact was formed on the front grid pattern by electroless plating followed by anneal ing at $380{\sim}400^{\circ}C$ for $15{\sim}30$ min at $N_{2}$ gas to allow formation of a nickel-silicide in a tube furnace or a rapid thermal processing(RTP) chamber because nickel is transformed to NiSi at $380{\sim}400^{\circ}C$. The Ni plating solution is composed of a mixture of $NiCl_{2}$ as a main nickel source. Cu was electroplated on the Ni layer by using a light induced plating method. The Cu electroplating solution was made up of a commercially available acid sulfate bath and additives to reduce the stress of the copper layer. The Ni/Cu contact was found to be well suited for high-efficiency solar cells and was successfully formed by using electroless plating and electroplating, which are more cost effective than vacuum evaporation. In this paper, we investigated low-cost Ni/Cu contact formation by electroless and electroplating for crystalline silicon solar cells.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2012년도 춘계학술발표대회 논문집
• /
• pp.267-273
• /
• 2012

Solar reforming of methane with CO2 was successfully tested with a direct irradiated absorber on a parabolic dish capable of 5kWth solar power. And the new type of double-layer absorber-the front layer, porous metal foam which absorbs the radiation and transfers the heat from material to gas, and the back layer, catalytically-activated metal foam-was prepared, and its activity was tested by using electric furnace. Ni was applied as the active metal on the gamma-Al2O3 coated Ni metal foam for the preparation of the catalytically-activated metal foam layer. Compared to conventional direct irradiation of the catalytically activated metal foam absorber, this new type of double layer absorber is found to exhibit a superior reaction and thermal storage performance at the fluctuating incident solar radiation. In addition, unlike direct irradiation of the foam absorber, double layer absorber has better thermal resistance, which prevents the emergence of cracks caused by mechanical or thermal shock. The total solar power absorbed reached up to 3.25kW and the maximum CH4 conversion was almost 59%.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 추계학술발표대회 논문집
• /
• pp.80-86
• /
• 2011

Solar reforming of methane with CO2 was successfully tested with a direct irradiated absorber on a parabolic dish capable of 5kWth solar power. And the new type of double-layer absorber - the front layer, porous metal foam which absorbs the radiation and transfers the heat from material to gas, and the back layer, catalytically-activated metal foam - was prepared, and its activity was tested by using electric furnace. Ni was applied as the active metal on the gamma-Al2O3 coated Ni metal foam for the preparation of the catalytically-activated metal foam layer. Compared to conventional direct irradiation of the catalytically activated metal foam absorber, this new type of double layer absorber is found to exhibit a superior reaction and thermal storage performance at the fluctuating incident solar radiation. In addition, unlike direct irradiation of the foam absorber, double layer absorber has better thermal resistance, which prevents the emergence of cracks caused by mechanical or thermal shock. The total solar power absorbed reached up to 3.25kW and the maximum CH4 conversion was almost 59%.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.76.1-76.1
• /
• 2010

Furnace를 이용한 $POCl_3$ 확산 공정은 실리콘 태양전지 제작과정에서 일반적으로 이용되는 에미터 층 형성 공정이다. 하지만, 확산 공정을 통해 P-N Junction을 형성할 경우 전면과 후면의 contact현상이 발생하게 되고 이를 제거하기 위해 Edge isolation 공정을 거치게 된다. 최근에는 레이저로 V 모양의 홈을 형성하는 방법이 이용되고 있다. 본 연구에서는 p-type 실리콘 웨이퍼 기판에 insulating barrier를 형성하여 edge isolation 공정을 없앤 Non-edge isolation공정을 제시한다. Non p-type 실리콘 웨이퍼에 insulating barrier를 형성한다. Insulating barrier가 형성된 BOE용액과 KOH에서의 견딤성 실험을 진행 하였다. 이후, p-type 단결정 실리콘 태양전지의 확산 공정을 진행하여 Non edge isolation 공정을 진행한 경우와 laser를 이용한 edge isolation 공정을 진행한 태양전지를 제작하여 특성을 비교하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.111-113
• /
• 2009

This paper shows that you can achieve high quality N+ emitter layers using a screen printable phosphorous diffusion paste and firing in an infrared belt furnace. Spreading resistance measurement from a beveled sample is used to measure carrier concentration as a function of depth for different phosphorous concentrations. Contours of estimated sheet resistance are shown for different processing conditions. This paper describes newly developed low cost phosphorous pastes. It shows the characterization of the newly developed phosphorous paste (DP99-038). This low cost pastes can easily be printed and make 16% efficiency.