• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.243-244
• /
• 2009

The $TiO_2$ nanofiber doped $TiO_2$ electrode area applied to dye-sensitized solar cells(DSSCs). The mixtures of $TiO_2$ nanofiber to $TiO_2$ photoelectrode has larger surface area than $TiO_2$ photoelectrode. In this research added 2.5, 5 and 10wt% $TiO_2$ nanofibers and the optimum condition of 5 wt% $TiO_2$ nanofiber's high surface area contributing the improvement of short-circuit photocurrent. The open-circuit voltage was 0.7V and solar energy conversion efficiency was 5.4%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.22-23
• /
• 2007

We tried to find the possibility of mono-crystalline silicon solar cell for photovoltaic concentrating system which is major cost portion for PV system using fresnel lens. With solar simulator and I-V curve tracer, we analyzed maximum output characteristics and measured the temperature of concentrated area using infrared camera. Because of temperature increase, there was no merit when concentrating. But at low radiant power, it showed more efficient operation. The combination of heat-sink technology and tracking system to our concentrating PV system would give better performance results.

• Laser Solutions
• /
• v.14 no.4
• /
• pp.9-13
• /
• 2011

The solar panel that consists of copper plate and copper tube was successfully welded by ultrasonic seam welding. However it was not only expensive the copper material but also ultrasonic welding has many problem such as high error rate, difficulty of dissimilar material welding, noise, etc. At this study, the laser welding of solar panel with aluminum plate instead of copper. The welding were carried out with the pulsed Nd:YAG laser and the weld bead geometry was measured with the variation of pulse energy. Consequently, there was no difference between the ultrasonic and the laser welding on the performance of heat transfer capacities. Also the formation of intermetalic compound such as CuAl2 was increased with the pulse energy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.463-464
• /
• 2009

This paper describes the political and technical trends of foreign 10 countries advanced in solar energy field. In the trend analysis, a couple of statistical data and related references were compared. As a result, all of the advanced countries mentioned in this paper have their own PV policy strategies and regulatory frameworks to strengthen their stable market structures and have financially supported by various types of incentives and tariff systems. It was confirmed that the political basis and technical regulations including electrical safety have to be prepared as soon as possible at both national and rural level in this country.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.13-14
• /
• 2008

In this paper, we analyze the electrical characteristics of PV depending on distance among solar cells before and after lamination process. From the result, the PV module's maximum power increases about 3.37% when solar cells's distance is 10mm. And the maximum power increases up to 8.42% when solar cells's maximum distance is 50mm. It is assumed that PV module's surface temperature decreases because of increasing distance between solar cells that would give high power generation. Also, short distance between solar cell and frame result in contamination on glass. When considering reduced maximum power caused by contaminant, from that, we can fabricated PV module of lower cost with high performance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.15-16
• /
• 2007

The high efficiency and low cost solar cells in order to it applied a dopant pastes diffusion process. The dopant pastes diffusion process which it uses is easily applied in screen-printing solar cells output line. in this paper, it used the Ferro 99-038 phosphorus diffusion pastes source and it analyzed a sheet resistance and a uniformity degree. And it knew the quality of the sheet resistance which it follows in temperature and time condition. The temperature variable it let and it fixed the time in 7 minutes. It will be able to measure the sheet resistance of $40({\Omega}/sq),\;30({\Omega}/sq),\; 20({\Omega}/sq)$. also average uniformity of the sheet resistance was below 5%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.16-17
• /
• 2007

To improve efficiency of solar cells, it is important to make a light trapping structure to reduce surface reflectance for increasing absorption of sun light within the solar cells. One of the promising methods that can reduce surface reflectance is isotropic texturing with acid solution based on hydrofluoric acid(HF), nitric acid($HNO_3$), and organic additives. Anisotropic texturing with alkali solution is not suitable for multicrystalline silicon wafers because of its different grain orientation. Isotropic texturing with acid solution can uniformly etch multicrystalline silicon wafers unrelated with grain orientation, so we can get low surface reflectance. In this paper, the acid texturing solution is made up of only HF and $HNO_3$ for easy controling the concentration and low cost compared to acid solution with organic additives. $HNO_3$ concentration and dipping time were varied to find the condition of minimum surface reflectance. Textured surfaces were observed Scanning Electron Microscope(SEM) and surface reflectance were measured. The best result of arithmetic mean(wavelength from 400nm to 1000nm) reflectance with acid texturing is 4.64% less than alkali texturing.

• Journal of the Korean Solar Energy Society
• /
• v.39 no.1
• /
• pp.21-32
• /
• 2019

Solar hot water system produces hot water using solar energy. If it is not used effectively, overheating occurs during the summer. Therefore, a lot of research is being done to solve this. This study develops thermoelectric power module applicable to solar hot water system. A thermoelectric material can directly convert thermal energy into electrical energy without additional power generation devices. If there is a temperature difference between high and low temperature, it generate power by Seebeck effect. The thermoelectric module generates electricity using temperature differences through the heat exchange of hot and cold water. The water used for cooling is heated and stored as hot water as it passes through the module. It can prevent overheating of Solar hot water system while producing power. The thermoelectric module consists of one absorption and two radiation part. There path is designed in the form of a water jacket. As a result, a temperature of the absorption part was $134.2^{\circ}C$ and the radiation part was $48.6^{\circ}C$. The temperature difference between the absorption and radiation was $85.6^{\circ}C$. Also, The Thermoelectric module produced about 122 W of irradiation at $708W/m^2$. At this time, power generation efficiency was 2.62% and hot water conversion efficiency was 62.46%.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.1
• /
• pp.125-132
• /
• 2010

Three organic sensitizers, JK-128, JK-129, and JK-130 containing quinoline unit are designed and synthesized. Under standard global AM 1.5 solar condition, the JK-130 sensitized solar cell gave a short circuit photocurrent density of 11.52 mA $cm^{-2}$, an open circuit voltage of 0.70 V, and a fill factor of 0.75, corresponding to an overall conversion efficiency of 6.07%. We found that the $\eta$ of JK-130 was higher than those of other two cells due to the higher photocurrent. The higher $J_{sc}$ value is attributed to the broad and intense absorption spectrum of JK-130.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.414-415
• /
• 2005

A solar cell is an element to transform the solar light energy into the electric energy in a moment. The single crystal element of high quality on which many studies were conducted in the past has a high efficiency of energy transformation, but its price competitiveness is so poor that it has failed to be popularized However, recently, in terms of an environment-friendly alternative energy, studies on applicability of the polycrystal solar cell have been actively under way. Among subject substances for such solar cell, $CuInSe_2$ has several good physical properties so that the greatest attention is paid to it as an optical absorption layer material for a low-cost solar cell of high efficiency. In order to manufacture the $CuInSe_2$ compound thin film, the unit element was deposited by using the sputtering method and the evaporation method and the heat treatment process was used in an electric furnace. Thereby, we intended to get a single-phase $CuInSe_2$ compound thin film.