• Journal of the Korean Solar Energy Society
• /
• v.40 no.4
• /
• pp.13-22
• /
• 2020

As the supply of photovoltaic (PV) increases worldwide, the cumulative installations in 2018 were 7.9 and 560 GW in Korea and the world, respectively. Typically, when the ground on commercial PV modules is installed, the area is limited; hence, new designs of PV modules are required to install additional PVs. Among the new design of PV modules, lightweight PV modules can be utilized in PV systems, such as buildings, farmlands, and floating PV. Concerning the investigation of lightweight PV modules, several studies on materials for replacing low-iron tempered glass, which comprises approximately 65% of the PV module weight, have been conducted. However, materials that are used as substitutes for glass should possess similar lightweight properties and reliability as glass. In this study, experimental tests were performed to evaluate the applicability of ethylene tetrafluoroethylene (ETFE) film with excellent resistance to water and aging as a front material of PV modules. The transmittance and ultraviolet properties of the ETFE film were determined and compared with those of glass. A 1-cell module and laboratory-scale 24-cell module were manufactured using the ETFE film and glass, and the electrical output was measured and analyzed. Furthermore, damp heat and thermal cycle tests were conducted to evaluate the reliability of the ETFE film module. Based on the experimental results, the electrical output and reliability of the ETFE film module were similar to those of the glass module, and the ETFE film could be used as the front material of PV modules.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.67-67
• /
• 2008

Application of organic materials with low cost, easy fabrication and advantages of flexible device are increasing attention by research work. Recently, one of them, organic solar cells were rapidly increased efficiency with regioregular poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyricacidmethylester (PCBM) used typical material. To increased efficiency of organic solar cell has tried control of domain of PCBM and crystallite of P3HT by thermal annealing and solvent vapor annealing. [4-6] In those annealing effects, be made inefficiently efficiency, which is increased fill factor (FF), and current density by phase-separated morphology with blended P3HT and PCBM. In addition, increased conductivity by modified hole transfer layer (HTL) such as Poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS), increased both optical and conducting effect by titanium oxide (TiOx), and changed cathode material for control work function were increased efficiency of Organic solar cell. In this study, we had described effect of organic photovoltaics by conductivity of interlayer such as PEDOT:PSS and TCO (Transparent conducting oxide) such as ITO, which is used P3HT and PCBM. And, we have measured with exactly defined shadow mask to study effect of solar cell efficiency according to conductivity of hole transfer layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.93-93
• /
• 2010

Semiconductor nanocrystal quantum dots (NQDs) have recently attracted considerable interest for use in photovoltaics. Band gaps of NQDs can be tuned over a considerable range by varying the particle size thereby allowing enhance absorption of solar spectrum. NQDs, synthesized using colloidal routes, are solution processable and promise for a large-area fabrication. Recent advancements in multiple-exciton generation in NQD solutions have afforded possible efficiency improvements. Various architectures have attempted to utilize the NQDs in photovoltaics, such as NQD-sensitized solar cell, NQD-bulk-heterojuction solar cell and etc. Here we have fabricated CdSe NQDs with the band gap of 1.8 eV to 2.1 eV on thin-layers of p-type organic crystallites (1.61 eV) to realize a donor-acceptor type heterojuction solar cell. Simple structure as it was, we could control the interface of electrode-p-layer, and n-p-layer and monitor the following efficiency changes. Specifically, surface molecules adsorbed on the NQDs were critical to enhance the carrier transfer among the n-layer where we could verify by measuring the photo-response from the NQD layers only. Further modifying the annealing temperature after the deposition of NQDs on p-layers allowed higher conversion efficiencies in the device.

• Electronic Materials Letters
• /
• v.14 no.6
• /
• pp.657-668
• /
• 2018

Organic-inorganic hybrid lead halide perovskites have been extensively investigated for various optoelectronic applications. Particularly, owing to their ability to form highly crystalline and homogeneous films utilizing low-temperature solution processes (< $150^{\circ}C$), perovskites have become promising photoactive materials for realizing high-performance flexible solar cells. However, the current use of mesoporous $TiO_2$ scaff olds, which require high-temperature sintering processes (> $400^{\circ}C$), has limited the fabrication of perovskite solar cells on flexible substrates. Therefore, the development of a low-temperature processable charge-transporting layer has emerged as an urgent task for achieving flexible perovskite solar cells. This review summarizes the recent progress in low-temperature processable electron- and hole-transporting layer materials, which contribute to improved device performance in flexible perovskite solar cells.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.78-81
• /
• 1994

The Photovoltaics(PV) industry has been evolving over the last 30 years and expanding because of a rising demand for clean and safe energy. Crystalline silicon solar cells will have increased performance and reduced cost in the future. In this paper solution growth process used to fabricate polycrystalline silicon thin film is considered.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.59.2-59.2
• /
• 2012

Polymer solar cells utilize bulk heterojunction (BHJ) type photo-active layer in which the electron donating polymer and electron accepting $C_{60}$ derivatives are blended. We found there is significant charge recombination at the interface between the BHJ active layer and electrode. The charge recombination at the interface was effectively reduced by inserting wide band gap inorganic interfacial layer, which resulted in efficiency and stability enhancement of BHJ polymer solar cell.

• Solar Energy
• /
• v.7 no.2
• /
• pp.14-21
• /
• 1987

For the purpose of a the application of photovoltaics, we have studied about photovoltaic systems for maned lighthouses. The current status of manned lighthouses in Korea are reviewed and detailed descriptions of the 6.48 Kwp photovoltaic system on Heuksando island are described in this paper. And we have discussed about expected effects and problems of this system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1208-1211
• /
• 2009

This study compares and contrasts the market size, growth rates, business cycles, supply and demand of the of the FPD and Photovoltaic (PV) industries. Using historic, market metric, cycle, capacity and other comparative analysis techniques, implications for implementing effective business strategies are formed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.209-209
• /
• 2012

High-efficient transparent conductive oxide (TCO) film-embedding Si heterojunction solar cells were fabricated. An additional doping was not applied for heterojunction solar cells due to the spontaneous junction formation between TCO films and an n-type Si substrate. Three different TCO coatings were formed by sputtering method for an Al-doped ZnO (AZO) film, an indium-tin-oxide (ITO) film and double stacks of ITO/AZO films. An improved crystalline ITO film was grown on an AZO template upon hetero-epitaxial growth. This double TCO films-embedding Si heterojunction solar cell provided significantly enhanced efficiency of 9.23% as compared to the single TCO/Si devices. The effective arrangement of TCO films (ITO/AZO) provides benefits of a lower front contact resistance and a smaller band offset to Si leading enhanced photovoltaic performances. This demonstrates a potential scheme of the effective TCO film-embedding heterojunction Si solar cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.72-72
• /
• 2011

Surface science is intrinsically related to the performance of solar cells. In solar cells the generation and collection of charge carriers determines their efficiency. Effective transport of charge carriers across interfaces and minimization of their recombination at surfaces and interfaces is of utmost importance. Thus, the chemistry at the surfaces and interfaces of these devices must be determined, and related to their performance. In this talk we will discuss the role of two important interfaces, First, the role of surface passivation is very important in limiting the rate of carrier of recombination. Here we will combine x-ray photoelectron spectroscopy of the surface of a Si device with electrical measurements to ascertain what factors determine the quality of a solar cell passivation. In addition, the quality of the heterojunction interface in a ZnSe/CdTe solar cell affects the output voltage of this device. X-ray photoelectron spectroscopy gives some insight into the composition of the interface, while ultraviolet photoemission yields the relative energy of the two materials' valence bands at the junction, which controls the open circuit voltage of the solar cell. The relative energies of ZnSe and CdTe at the interface is directly affected by the material quality of the interface through processing.