• Journal of the Korean Solar Energy Society
• /
• v.31 no.2
• /
• pp.37-46
• /
• 2011

The GWNU (Gangnung-Wonju national university) solar radiation model was developed with radiative transfer theory by Iqbal and it is applied the NREL (National Research Energy Laboratory). Input data were collected and accomplished from the model prediction data from RDAPS (Regional Data Assimilated Prediction Model), satellite data and ground observations. And GWNU solar model calculates not only horizontal surface but also complicated terrain surface. Also, We collected the statistical data related on photovoltaic power generation of the Korean Peninsula and analyzed about photovoltaic power efficiency of the Gangwon region. Finally, the solar energy resource and photovoltaic generation possibility map established up with 4 km, 1 km and 180 m resolution on Gangwon region based on actual equipment from Shinan solar plant,statistical data for photovoltaic and complicated topographical effect.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.9
• /
• pp.14-25
• /
• 2011

The solar vehicle is in the spotlight in the eco-friendly aspect of photovoltaic system using unlimited solar energy. The solar vehicle uses energy of photovoltaic and battery. The solar vehicle uses stored energy in battery when photovoltaic power is lower than consumption power by solar vehicle and if photovoltaic power is higher than consumption power by solar vehicle then photovoltaic power is stored to battery. To improve use efficiency of photovoltaic, the researches about MPPT method to operate maximum power point and interior permanent magnet synchronous motor(IPMSM)drive system using photovoltaic is necessary. This paper proposes MPPT control algorithm for solar vehicle using new fuzzy control(NFC). In this paper, to reduce switching loss, the DC-DC converter is omitted. The NFC controller can be use instead of PO. The NFC controller is performed MPPT control using solar cell voltage and q -axis current of IPMSM. The output of NFC is command q -axis current of IPMSM and this current is operated IPMSM. The response characteristics of algorithm proposed in this paper is compared response characteristics of conventional PO method by PSIM program and validity of this paper prove using this result.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.356-360
• /
• 2009

Recent global environmental pollution and contamination and depletion of limited fossil energy prices surge as an energy source to replace it depending on wind, fuel cells and solar power and other renewable and pollution free renewable energy is of interest in increase. The photovoltaic systems are pollution-free, unlimited energy source, and easy to install because it is rated as the most valuable renewable energy sector and the prevalence is spreading throughout the world. Photovoltaic systems at one end of the stable development of the role that solar power inverter applications can be the most important. No matter how much power the solar arrays, even if the inverter output in the normally if he's no use. These photovoltaic inverters to evaluate the performance of the inverter efficiency measures that can be called directly. This way of measuring the efficiency of solar inverters in Europe efficiency and CEC efficiency is currently being used. In this paper, until now about how to measure the efficiency of solar power inverter technology and the new Korean Meteorological Solar Insolation data analysis to derive weights based on this inverter efficiency for Korea is to offer.

• Structural Engineering and Mechanics
• /
• v.89 no.2
• /
• pp.171-179
• /
• 2024

The market of the floating solar photovoltaic system is rapidly growing around the world with the rise of renewable energy that can replace fossil energy. While the floating solar photovoltaic system is operating and being installed in several countries, the system is exposed to the risk in terms of structural safety due to the absence of the proper design guideline. In this paper, design loads suitable for the floating solar photovoltaic system are presented. Utilizing the existing reliable design standards such as ASCE 7-16 (ASCE 7-16 2016) and DNV-RP-C205 (DNV-RP-C205 2010), the appropriate design loads for the floating solar photovoltaic system are presented. The proper load combinations are also presented by putting wave load based on DNV standards (DNV-OS-C101 2015 and DNV-OS-C201 2015) into the load combinations in ASCE standards (ASCE 7-16 2016). We present the load combinations for the allowable stress design and load and resistance factor design, respectively.

• 한국태양에너지학회:학술대회논문집
• /
• 2008.11a
• /
• pp.53-56
• /
• 2008

A photovoltaic panel is a device that, through the photovoltaic effect, converts luminous energy into electric energy. Photovoltaic generation system used infinity of solar energy, cost of fuel is needless and there in no air pollution or waste occurrence. This paper summarizes the results of these efforts by offering a photovoltaic system structure in 30[kW] large scale applications installed in Mokpo National University dormitory roof. The status of photovoltaic system components, are inter-connection and safety equipment monitoring system will be summarized as this article. This describes configuration of utility interactive photovoltaic system which generated power supply for dormitory. In this paper represent 30[kW] utility photovoltaic system examination result.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.9
• /
• pp.33-39
• /
• 2012

For photovoltaic power generation need certainly decreasing module's price and increasing promote efficiency technology. Almost of solar panel is on the decrease energy efficiency since 2,000. like silicone(Si) solar panel, thin film solar panel and etc. Silicone(Si) solar panel was best efficiency in 1999. It's 24%. But after that time, It didn't pass limit of energy efficiency. That's why, nowadays being issued that using III-V compound semiconductor to high efficiency of concentrating photovoltaic system for making an alternative proposal. In Korea, making researches in allied technology with III-V compound semiconductor solar panel, condenser technology, and solar tracker. but feasibility study for concentrating photovoltaic power generation hasn't progressed yet. This thesis made a plan about CPV(Concentrating Photovoltaic)system and CPV has a higher energy efficiency than PV(Photovoltaic)system in fine climate conditions from comparing CPV with using silicone(Si) solar panel to PV's efficiency test result.

• Journal of the Korean Solar Energy Society
• /
• v.24 no.3
• /
• pp.19-25
• /
• 2004

The measured solar radiation incident on tilted surfaces by all directions has been widely used as important solar radiation data in installing photovoltaic modules. To maximize the incident beam radiation, the slope, which is the angle between the plane of the surface in question and the horizontal, an4 the solar azimuth angles are needed for these solar photovoltaic systems. This is because the performance of the solar photovoltaic systems is much affected by angle and direction of incident rays. Recognizing those factors mentioned above are of importance, actual experiment has been performed in this research to obtain the an91e of inclination with which the maximum incident rays can be absorbed. The results obtained in this research could be used in installing optimal photovoltaic modules.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.3
• /
• pp.11-18
• /
• 2012

To expect accurately the maximum power of solar cell module under various installation conditions, it is required to know the performance characteristics like temperature dependence. Today, the PV (photovoltaic) market in Korea has been growing. Also BIPV (building integrated photovoltaic) systems are diversified and become popular. But thermal dependence of PV module is little known to customers and system installers. In IEC 61215,a regulation for testing the crystalline silicon solar cell module, the testing method is specified for modules. However there is limitation for testing the module with diverse application examples. In extreme installation method, there is no air flow between rear side of module and ambient, and it can induce temperature increase. In this paper, we studied the roof type installation of PV module on the surface of one-axis tracker system. We measured temperature on every component of PV module and compared to open-rack structure. As a result, we provide the foundation that explains temperature characteristics and NOCT (nominal operation cell temperature) difference. The detail description will be specified as the following paper.

• Electronic Materials Letters
• /
• v.14 no.6
• /
• pp.718-724
• /
• 2018

With the development of photovoltaic industry, the cost of photovoltaic power generation has become the significant issue. And the metallization process has decided the cost of original materials and photovoltaic efficiency of the solar cells. Nowadays, double printing process has been introduced instead of one-step printing process for front contact of polycrystalline silicon solar cells, which can effectively improve the photovoltaic conversion efficiency of silicon solar cells. Here, the relative cheap Cu paste has replaced the expensive Ag paste to form Ag/Cu composite front contact of silicon solar cells. The photovoltaic performance and the cost of photovoltaic power generation have been investigated. With the optimization on structure and height of Cu finger layer for Ag/Cu composite double-printed front contact, the silicon solar cells have exhibited a photovoltaic conversion efficiency of 18.41%, which has reduced 3.42 cent per Watt for the cost of photovoltaic power generation.

• Journal of the Korean Solar Energy Society
• /
• v.35 no.5
• /
• pp.57-65
• /
• 2015

The Potential Induced Degradation(PID) in PV module mainly affected by various performance conditions such as a potential difference between solar cell and frame, ambient temperature and relative humidity. The positive charges as sodium ions in front glass reach solar cell in module by a potential difference and are accumulated in the solar cell. The ions accelerate the recombination of generation electrons within solar cell under illumination, which reduces the entire output of module. Recently, it was generally known that PID generation is suppressed by controlling the thickness of SiNx AR coating layer on solar cell or using Sodium-free glass and high resistivity encapsulant. However, recovery effects for module with PID are required, because those methods permanently prevent generating PID of module. PID recovery method that voltage reversely applies between solar cell and frame contract to PID generation begins to receive attention. In this paper, PID recovery tests by using voltage under various outdoor conditions as humidity, temperature, voltage are conducted to effectively mitigate PID in module. We confirm that this recovery method perfectly eliminates PID of solar cell according to repeative PID generation and recovery as well as the applied voltage of three factors mainly affect PID recovery.