• 한국세라믹학회지
• /
• 제55권4호
• /
• pp.325-336
• /
• 2018

Perovskite solar cells (PSCs) are a new class of photovoltaic devices, which have attracted significant attention due to their remarkable optoelectrical properties, including high absorption coefficients, high carrier mobilities, long carrier diffusion lengths, tunable bandgaps, low cost, and facile fabrication. PSCs have reached efficiencies of 22.70% and 18.36% on rigid fluorine-doped tin oxide and poly(ethylene terephthalate) substrates, respectively; these are comparable to those of single-crystal silicon and copper-indium-gallium-selenium solar cells. Over the past eight years, the photo conversion efficiency of PSCs has been significantly improved by device-architecture adjustments, and absorber and electron/hole transport layer optimization. Each layer is important for the performance of PSCs; hence, we discuss achievements in flexible perovskite solar cells (FPSCs), covering electron/hole-transport materials, electrode materials. We give a comprehensive overview of FPSCs and put forward suggestions for their further development.

• Journal of information and communication convergence engineering
• /
• 제9권4호
• /
• pp.461-465
• /
• 2011

An aluminum doped zinc oxide (AZO) film for front contacts of thin film solar cells, in this work, were deposited by r.f. magnetron sputtering, and then etched in diluted hydrochloric acid solution for different times. Effects of surface texturing on the electro-optical properties of AZO films were investigated. Also, to clarify the light trapping of textured AZO film, amorphous silicon thin film solar cells were fabricated on the textured AZO/glass substrate and the performance of solar cells were studied. After texturing, the spectral haze at the visible range of 400 ~750 nm increased substantially with the etching time, without a change in the resistivity. The conversion efficiency of amorphous Si solar cells with textured AZO film as a front electrode was improved by the increase of short-circuit current density ($J_{sc}$), compared to cell with flat AZO films.

• 한국전기전자재료학회논문지
• /
• 제27권12호
• /
• pp.776-791
• /
• 2014

A marvellous solar cell technology system based on organometal halide perovskites has recently shown an unprecedented progress in power conversion efficiency (PCE); the certified one of 17.9% and unconfirmed of 19.3%, as well as the estimated electricity with a generating cost lower than the half of conventional methods based on fossil fuels. In this report the present status of stability with regards to moisture, ambient temperature, ultraviolet and lead toxicity as well as the key technological developments for the early commercialization are covered. Comprehensive understanding of material science for perovskites is required, together with complete encapsulation technologies beyond those for OLEDs, in order to ensure a 20-year-longer-than lifetime of PSCs (perovskite solar cells) and the stability according to the IEC 61646 damp heat test standard, which will result in the replacement of silicon solar cells with PSCs.

• 정보저장시스템학회논문집
• /
• 제9권2호
• /
• pp.67-71
• /
• 2013

The fabrication method of plasmonic nanodots on silicon substrate has been developed to improve the efficiency of thin film solar cells. Nanoscale metallic nanodots arrays are fabricated by anodic aluminum oxide (AAO) template mask which can have different structural parameters by varying anodization conditions. In this paper, the structural parameters of gold nanodots, which can be controlled by the diverse structures of AAO template mask, are investigated to enhance the optical properties of a-Si thin film solar cells. It is found that optical properties of the thin film solar cells are improved by finding optimization values of the structural parameters of the gold nanodot array.

• 한국전기전자재료학회논문지
• /
• 제37권4호
• /
• pp.439-444
• /
• 2024

This study investigates the post-thermal treatment effects on the efficiency of silicon heterojunction solar cells, specifically examining the influence of annealing on p-type microcrystalline silicon oxide and ITO thin films. By assessing changes in carrier concentration, mobility, resistivity, transmittance, and optical bandgap, we identified conditions that optimize these properties. Results reveal that appropriate annealing significantly enhances the fill factor and current density, leading to a notable improvement in overall solar cell efficiency. This research advances our understanding of thermal processing in silicon-based photovoltaics and provides valuable insights into the optimization of production techniques to maximize the performance of solar cells.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.171-171
• /
• 2012

We have studied the effects of plasma treatments on CdS buffer layers in CIGS thin film solar cells. The CdS layers were deposited on CIGS films by chemical bath deposition (CBD) method. The RF plasma treatments of the CdS thin films were performed with Ar, $O_2 and $N_2 gases, respectively. After plasma treatments, the solar cells with Al:ZnO/i-ZnO/CdS/CIGS structures were fabricated. The surface properties of the CdS/CIGS thin films after plasma treatments were investigated with SEM, EDX and AFM measurements. The electrical properties of manufactured solar cell were discussed with the results of current-voltage measurements. The plasma treatments have a strong influence on the open circuit voltage (VOC) and the fill factor of the solar cells. Finally, a correlation between the surface properties of CdS layer and the efficiencies of the CIGS thin film solar cells is discussed.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.432.1-432.1
• /
• 2016

We demonstrated that the power conversion efficiency (PCE) of bilayer solar cell was significantly enhanced by inserting interfacial layer between the organic bilayer film and the Al electrode. Moreover, the water contact angle shows that the bilayer solar cells suffer from the undesirable surface component which limits the charge transport to the Al electrode. The AFM measurement has revealed that the pre- and post-thermal annealing treatments results in different morphologies of the interfacial layer which is critical for the higher PCE of the bilayer solar cells. Furthermore we have investigated the electrical properties of the bilayer solar cells and obtained insights into the detailed device mechanisms. The transient photovoltage measurements suggests that the significantly enhanced Voc is caused by reducing the recombination at the interface between the organic films and the Al electrode. By inserting the TiO2 layer between the bilayer film and Al electrode, the open circuit voltage (Voc) was increased from 0.37 to 0.66V. Consequently, the power conversion efficiency (PCE) of bilayer solar cells was significantly enhanced from 1.23% to 3.71%. As the results, the TiO2 interfacial layer can be used to form an ohmic contact layer, serveing as a blocking layer to prevent the penetration of the Al, and to reduce the recombination at the interface.

• Transactions on Electrical and Electronic Materials
• /
• 제4권4호
• /
• pp.22-25
• /
• 2003

High series resistance due to the presence of glass frit is one of the major problems for screen printed silicon solar cells. Cells having electrical parameters below the prescribed values are usually rejected during solar module fabrication. Therefore, it is highly desirable to improve the electrical parameters of the silicon solar cells and thereby to increase the overall production yield. It was observed that, the performance of low quality mono-crystalline silicon solar cells made by standard screen printing technology could be improved remarkably by novel surface treatment. We have chemically treated the surface using sodium hydroxide (NaOH) and silver nitrate ($AgNO_3$) solutions. NaOH treatment helps to reduce the series resistance by decreasing the presence of excess glass frit on the top silver grid contact. The $AgNO_3$ treatment is used to reduce the series resistance comes from the deposition of silver on the grids by filling the holes present (if any) within the grid pattern.

• 전기화학회지
• /
• 제12권4호
• /
• pp.301-310
• /
• 2009

본 논문에서는 현재 많이 연구되고 있는 염료감응 태양전지에 대해 전기화학적 접근을 통해 설명한다. 특히, 기존 도핑 개념을 적용하는 반도체 태양전지와 다른 점을 비교 설명하고, 이론적으로 어떻게 태양전지가 형성될 수 있는지를 설명한다. 또한 염료감응 태양전지가 탄생되게 된 과정을 고찰해 본다. 이어서, 태양전지에서 많이 사용되는 전기화학적 분석법을 설명하고, 어떻게 적용될 수 있는지 임피던스 분석법을 통해 설명한다. 전기화학에서 많이 사용되는 임피던스와 순환전압전류법을 통해, 염료감응 태양전지를 이루는 주성분인 금속산화물과 염료, 전해질의 에너지준위 분석법에 대해서 간단히 소개한다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.467.1-467.1
• /
• 2014

Quantum dots (QD) solar cells has received considerable attention due to their potential of improving the overall conversion efficiency by harvesting excess energy via multiple excitons generation (MEG). Although there have been many reports which show MEG phenomena by using optical measurement of quantum dots themselves, carrier multiplication in real QD photovoltaic devices has been sparsely reported due to difficulty in dissociation of excitons and charge collection. In this reports, heterojunction QD solar cells composed of PbS QD monolayer on highly crystalline $TiO_2$ thin films were fabricated by using Langmuir-Blodgett deposition technique to significantly reduce charge recombination at the interfaces between each QD. The PbS CQDs monolayer was characterized by using UV-vis, transmission electron microscopy (TEM) and atomic force microscopy (AFM). The internal quantum efficiency (IQE) for the monolayer QD solar cells was obtained by measurement of external quantum efficiency and determining light absorption efficiency of active layer. Carrier multiplication was observed by measuring IQE greater than 100% over threshold photon energy. Our findings demonstrate that monolayer QD solar cell structure is potentially capable of realizing highly efficient solar cells based on carrier multiplication.