• 자동차안전학회지
• /
• 제14권1호
• /
• pp.55-61
• /
• 2022

Along with global environmental issues, the size of the electric vehicle market has recently skyrocketed. Various efforts have been made to extend mileage, one of the biggest problems of the electric vehicles, and development of batteries with high energy densities has led to exponential growth in mileage and performance. However, proper thermal management is essential because these high-performance batteries are affected by continuous heat generation and can cause fires due to thermal runaway phenomena. Therefore, thermal management of the battery is studied through the optimal design of the guide vanes, while utilizing the existing battery casing to ensure the safety of the electric vehicles. A battery from T-company, one of a manufacturer of the electric vehicles, was used for the research, and the commercial CFD software, ANSYS CFX V20.2, was used for analysis. The guide vanes were derived through optimal design based on a genetic algorithm with flow analysis. The optimized guide vanes show improved heat removal performance.

• Geomechanics and Engineering
• /
• 제34권1호
• /
• pp.69-86
• /
• 2023

To overcome the dilemma of the [BQ] method's inability to predict mountain tunnel support loads, this study is based on the Hoek-Brown criterion and previous results to obtain the connection equations from GSI scores to each parameter of the Hoek-Brown criterion and the link between the [BQ] scores and the GSI system. The equations were embedded in the Hoek-Brown criterion of FLAC6.0 software to obtain tunnel construction forecasts without destroying the in-situ stratigraphy. The feasibility of the secondary development of the Hoek-Brown criterion was verified through comparative analysis with field engineering measurements. If GSI > 45 with a confining pressure of less than 10 MPa, GSI has little effect on the critical softening factor while we should pay attention to the parameter of confining pressure when GSI < 45. The design values for each parameter are closer to the FLAC3D simulation results and the secondary development of the Hoek-Brown criterion meets the design objectives. If the Class V surrounding rock is thinned with shotcrete or the secondary lining is installed earlier, the secondary lining may act as the main load-bearing structure. The study may provide ideas for rapid prediction of mountainous tunnels in China.

• 한방재활의학과학회지
• /
• 제33권3호
• /
• pp.79-96
• /
• 2023

Objectives This study was designed to review the effect of Jakyakkamchobuja-tang on rat model with rheumatoid arthritis. Methods We used seven databases (PubMed, EMBASE, Cochrane CENTRAL, China National Knowledge Infrastructure, Oriental Medicine Advanced Searching Integrated System, Korean studies Information Service System, National Digital Science Library) from their inception to May 2023 without language restrictions. Systematic Review Centre for Laboratory Animal Experimentation's tool was used to evaluate the risk of bias. RevMan software (V5.4) was used for the meta-analysis. Results Five studies were selected following our inclusion criteria. The arthritis index decreased significantly (standardized mean difference=-2.06; 95% confidence interval=-3.07 to -1.04; p<0.0001) in Jakyakkamchobuja-tang group. Also, serum cytokines in serum and paw swelling degree decreased in Jakyakkamchobuja-tang group. Conclusions Jakyakkamchobuja-tang may be effective in treating rheumatoid arthritis. Although there is a limitation that the design of drug dosage varies between papers, it can be expected to be applied as an alternative to Western medicine, and it is believed to contribute to the standardization of herbal treatment for rheumatoid arthritis.

• Geomechanics and Engineering
• /
• 제32권4호
• /
• pp.387-396
• /
• 2023

Ground subsidence, which is a current concern that affects piled raft foundations, has occurred at a high rate in Ho Chi Minh City, Viet Nam, due primarily to groundwater pumping for water supply. In this study, the groundwater level (GWL) change affect on a piled raft foundation was investigated based on the three-dimensional finite element method (3D-FEM) using the PLAXIS 3D software. The GWL change due to global groundwater pumping and dewatering were simulated in PLAXIS 3D based on the GWL reduction and consolidation. Settlement and the pile axial force of the piled raft foundation in Ho Chi Minh subsoil were investigated based on the actual design and the proposed optimal case. The actual design used the piled foundation concept, while the optimal case applied a pile spacing of 6D using a piled raft concept to reduce the number of piles, with little increased settlement. The results indicated that the settlement increased with the GWL reduction, caused by groundwater pumping and dewatering. The subsidence started to affect the piled raft foundation 2.5 years after construction for the actual design and after 3.4 years for the optimal case due to global groundwater pumping. The pile's axial force, which was affected by negative skin friction, increased during that time.

• PNF and Movement
• /
• 제20권1호
• /
• pp.59-66
• /
• 2022

Purpose: The aim of this research was to verify the relationship between three-dimensional (3D) ground reaction force (GRF) and severity of leg length discrepancy (LLD) while walking at a normal speed. It used a 3D motion analysis system with force platforms in standing workers with LLD. Methods: Subjects comprising 45 standing workers with LLD were selected. Two force platforms were used to acquire 3D GRF data based on a motion analysis system during gait. Vicon Nexus and Visual3D v6 Professional software were used to analyze kinetic GRF data. The subjects were asked to walk on a walkway with 40 infrared reflective markers attached to their lower extremities to collect 3D GRF data. Results: The results indicated the maximal force in the posterior and lateral direction of the long limb occurring in the early stance phase during gait had significant positive correlation with LLD severity (r = 0.664~0.738, p <0.01). In addition, the maximal force medial direction of the long limb occurring in the late stance phase showed a highly positive correlation with the LLD measurement (r = 0.527, p <0.01). Conclusion: Our results indicate that greater measured LLD severity results in more plantar pressure occurring in the foot area during heel contact to loading response of the stance phase and the stance push-off period during gait.

• Earthquakes and Structures
• /
• 제23권3호
• /
• pp.283-295
• /
• 2022

Seismic design codes permit the use of Equivalent Static Analysis of buildings considering torsional eccentricity e with dynamic amplification factors on structural eccentricity and some accidental eccentricity. Estimation of e in buildings is not addressed in codes. This paper presents a simple approximate method to estimate e in RC Moment Frame and RC Structural Wall buildings, which required no detailed structural analysis. The method is validated by 3D analysis (using commercial structural analysis software) of a spectrum of building. Results show that dynamic amplification factor should be applied on torsional eccentricity when performing Response Spectrum Analysis also. Also, irregular or mixed modes of oscillation arise in torsionally unsymmetrical buildings owing to poor geometric distribution of mass and stiffness in plan, which is captured by the mass participation ratio. These irregular modes can be avoided in buildings of any plan geometry by limiting the two critical parameters (normalised torsional eccentricity e/B and Natural Period Ratio 𝜏 =T_𝜃/T, where B is building lateral dimension, T_𝜃 uncoupled torsional natural period and T uncoupled translational natural period). Suggestions are made for new building code provisions.

• 근관절건강학회지
• /
• 제30권3호
• /
• pp.218-229
• /
• 2023

Purpose: This study aimed to assess and compare the effectiveness of various fall prevention interventions in hospitals through a network meta-analysis. Methods: A network meta-analysis was conducted using the "netmeta" package in R software (v4.1), employing a frequency method. Odds ratios of fall rates and injurious fall rates were utilized to confirm the effects of interventions for fall prevention. Comparative rankings of these interventions were determined using cumulative probability (P-score). Results: Comparative rankings via cumulative probability (P-scores) revealed individualized education as the most effective intervention for fall incidence (P-Score 87.8%). Followed by fall-preventing sensors (60.9%), multicomponent interventions (47.4%), usual care (33.2%), and environmental modification (20.7%). For fall-related injuries, individualized education ranked highest (P-Score 97.1%), followed by multicomponent interventions (76.0%), usual care (47.6%), environmental modification (24.2%), and fall-preventing sensors (5.1%). Conclusion: This study provides valuable insights into the relative effectiveness of diverse interventions in preventing fall incidence through network meta-analysis. The findings aim to support nurses in making informed decisions when implementing fall prevention strategies in clinical practice.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제17권12호
• /
• pp.3310-3329
• /
• 2023

This work designs an eighteen-channel bidirectional Intensity Modulation with Direct Detection (IM/DD) Wavelength Division Multiplexing-Passive Optical Network (WDM-PON) system. The proposed system meets the requirement of the ITU-T 5G fronthaul link suggested design in G-series Recommendations-Supplement 66. The newly designed system, with a 25Gb/s/λ data rate (450Gbps as a system capacity), has been tested and simulated using OptiSystem V.19 software. The system has been evaluated by the BER with respect to variable the optical span and CW laser power. Based on the ITU-T recommendations, the simulation results demonstrate that this system might be used as an F1 and as an Fx 5G fronthaul link for functional split choices starting from options 1 to 7a. These options are required under 25Gbps/λ for each upstream and downstream link direction. Furthermore, the proposed system utilized a bidirectional single-mode optical fiber within short optical spans of up to 10 km. The proposed system is characterized by a low-cost, simple, DSP-free and amplifier-free system with a reasonable system capacity.

• 핵의학기술
• /
• 제19권1호
• /
• pp.62-66
• /
• 2015

Brain PET/CT 검사는 뇌의 정신활동 뿐만 아니라 혈액의 관류상태, 에너지원의 대사상태, 생리적 활성물질의 섭취 정도를 관찰할 수 있으며 이를 통계적으로 분석하기 위한 다양한 데이터 비교 방법들이 적용되고 있다. 본 논문에서는 다양한 데이터 비교 방법들 중 SPM과 scenium의 유용성을 비교 평가 하였다. 2014년 3월부터 7월까지 서울대학교병원에서 18F-FDG PET/CT 검사를 시행 받은 15명(평균연령 $62.02{\pm}15.03$세, abnormal 10명, normal 5명)의 데이터를 분석하였다. 사용된 장비는 Siemens사의 Biograph Truepoint40 with TrueV이며 데이터 분석을 위하여 SPM99, syngo.via version VA30A, scenium version 4.0이 사용되었다. 검사는 $^{18}F-FDG$를 kg당 3.7MBq 주사하여 30분 후 brain emission 영상을 10분 획득하였다. 획득된 영상을 이용하여 영상 판독과 SPM, scenium 결과의 일치성을 5명의 핵의학과 판독의가 평가하였다. Scenium에서 parameter 변경에 따른 SUV와 SD 변화를 평가하기 위하여 환자 data 재구성시 iteration 4, 6, 8, gaussian filter 2mm, 4mm, 8mm, matrix size 168, 256, 336의 변화를 주어 재구성후 증감을 평가하였다. 마지막으로 3명의 방사선사가 두 software를 이용하여 평균 결과 분석 시간을 평가하였다. 영상 판독과 SPM 결과의 일치성은 normal 89.5%, abnormal 73.2%로 normal 환자에서 보다 높은 일치성을 보였으며 total 84.1%의 일치하는 것으로 나타났다. Scenium에서는 normal 92.1%, abnormal 93.0% 그리고 total 92.4%로 나타났다. Scenium에서 parameter 변경에 따른 SUV와 SD 변화 평가에서 iteration 횟수와 matrix size가 감소할수록 SUV와 SD 값은 iteration 변화에서 최대 0.59%, 8.73% 그리고 matrix size 변화에서 최대 0.88%, 8.25% 감소하였다. Gaussian filter변화에서는 FWHM이 증가할수록 SUV와 SD값은 최대 4.69%, 20.38% 감소하였다. 두 software를 이용한 평균 결과 분석 시간은 SPM 282초, scenium 116초로 scenium으로 결과 분석 시 SPM 사용 시 보다 58.% 시간이 감소되었다. 데이터 비교 평가 software들의 장단점을 충분히 이해하고 각 병원의 장비 환경과 실정에 맞는 software를 적용한다면 brain PET/CT 검사 시 보다 많은 정보를 제공할 수 있을 것으로 사료된다.

• 한국위성정보통신학회논문지
• /
• 제1권2호
• /
• pp.95-100
• /
• 2006

통신해양기상위성의 전력계는 향상된 Eurostar 3000 버전에 바탕을 두고 있다. Eurostar 3000 전력계는 정상상태 또는 하나의 결함에서도 자율적으로 동작하며 높은 수준의 재구성 능력 및 유연성을 제공한다. 본 논문에서는 통신해양기상위성 전력계 예비설계 결과를 소개한다. 통신해양기상위성 전력계는 하나의 배터리, 태양전지어레이 윙, 전력공급기, 파이로 유닛 및 태양전지어레이 구동기 그리고 릴레이 및 퓨즈 브래킷 들로 구성된다. 통신해양기상위성 전력계는 3 kW의 버스 전력을 제공할 수 있다. 태양전지어레이는 2개의 태양전지판으로 구성된 전개할 수 있는 윙으로 구성된다. 태양전지는 GaAs/Ge 3중 접합 셀로 선정되었다. Li-ion 배터리는 10개의 직렬 연결된 셀 모듈로 구성되며 각 모듈은 셀 5개가 병렬로 연결된다. 전력공급기는 태양전지어레이 및 배터리와 함께 50 V로 완전 정류된 하나의 전력 버스를 생성한다. 전력 버스는 릴레이 및 퓨즈 브래킷 들에 의해 중앙 집중되어 보호되고 분배된다. 파이로 유닛은 점화 작동기 장치로 전력을 공급한다. 태양전지어레이는 자세제어계의 제어로 태양전지어레이 구동기에 의해 회전된다. 전력계의 제어 및 감시는, 특히 배터리, 전력공급기와 탑재 소프트웨어의 결합으로 수행된다.