• Progress in Medical Physics
• /
• v.27 no.4
• /
• pp.213-219
• /
• 2016

The position verification of the radiation source utilized in brachytherapy forms a critical factor in determining the therapeutic efficiency. Currently, films are used to verify the source position; however, this method is encumbered by the lengthy time interval required from film scanning to analysis, which makes real-time position verification difficult. In general, the source position accuracy is usually tested in a monthly quality assurance check. In this context, this study investigates the feasibility of the real-time position verification of the radiation source in high dose rate (HDR) brachytherapy with the use of scintillating fibers. To this end, we construct a system consisting of scintillating fibers and a silicon photomultiplier (SiPM), optimize the dosimetric software setup and radiation system characteristics to obtain maximum measurement accuracy, and determine the relative ratio of the measured signals dependent upon the position of the scintillating fiber. According to the dosimetric results based on a treatment plan, in which the dwell time is set at 30 and 60 s at two dwell positions, the number of signals is 31.5 and 83, respectively. In other words, the signal rate roughly doubles in proportion to the dwell time. The source position can also be confirmed at the same time. With further improvements in the spatial resolution and scintillating fiber array, the source position can be verified in real-time in clinical settings with the use of a scintillating fiber-based system.

• Journal of Information Processing Systems
• /
• v.6 no.1
• /
• pp.1-20
• /
• 2010

Due to the convergence of voice, data, and video, today's telecom operators are facing the complexity of service and network management to offer differentiated value-added services that meet customer expectations. Without the operations support of well-developed Business Support System/Operations Support System (BSS/OSS), it is difficult to timely and effectively provide competitive services upon customer request. In this paper, a suite of NGOSS-based Telecom OSS (TOSS) is developed for the support of fulfillment and assurance operations of telecom services and IT services. Four OSS groups, TOSS-P (intelligent service provisioning), TOSS-N (integrated large-scale network management), TOSS-T (trouble handling and resolution), and TOSS-Q (end-to-end service quality management), are organized and integrated following the standard telecom operation processes (i.e., eTOM). We use IPTV and IP-VPN operation scenarios to show how these OSS groups co-work to support daily business operations with the benefits of cost reduction and revenue acceleration.

• KIPS Transactions on Software and Data Engineering
• /
• v.10 no.6
• /
• pp.211-222
• /
• 2021

Recently, frozen and refrigerated appliances on the market are being released with additional IoT functions, but there are few tests on IoT functions. In particular, the existing test system does not have IoT test items for IoT-based frozen and refrigerated appliances, making it difficult for companies to find the cause even if defects occur, and test institutions are also restricted from selecting IoT-related test items and conducting correct performance tests. In this paper, we design a test item framework that can identify product defects and identify causes in the performance test process of frozen and refrigerated products with IoT functions among products in the home appliance field, and propose test methods and management measures using them. Through the proposed research, manufacturers and testing institutions can test the correct performance of IoT-based frozen and refrigerated products, thereby enhancing the completeness and securing reliability of the products.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.30 no.5
• /
• pp.909-928
• /
• 2020

From the early 1970s, the US government began to recognize that penetration testing could not assure the security quality of products. Results of penetration testing such as identified vulnerabilities and faults can be varied depending on the capabilities of the team. In other words none of penetration team can assure that "vulnerabilities are not found" is not equal to "product does not have any vulnerabilities". So the U.S. government realized that in order to improve the security quality of products, the development process itself should be managed systematically and strictly. Therefore, the US government began to publish various standards related to the development methodology and evaluation procurement system embedding "security-by-design" concept from the 1980s. Security-by-design means reducing product's complexity by considering security from the initial phase of development lifecycle such as the product requirements analysis and design phase to achieve trustworthiness of product ultimately. Since then, the security-by-design concept has been spread to the private sector since 2002 in the name of Secure SDLC by Microsoft and IBM, and is currently being used in various fields such as automotive and advanced weapon systems. However, the problem is that it is not easy to implement in the actual field because the standard or guidelines related to Secure SDLC contain only abstract and declarative contents. Therefore, in this paper, we present the new framework in order to specify the level of Secure SDLC desired by enterprises. Our proposed CIA (functional Correctness, safety Integrity, security Assurance)-level-based security-by-design framework combines the evidence-based security approach with the existing Secure SDLC. Using our methodology, first we can quantitatively show gap of Secure SDLC process level between competitor and the company. Second, it is very useful when you want to build Secure SDLC in the actual field because you can easily derive detailed activities and documents to build the desired level of Secure SDLC.

• KIPS Transactions on Software and Data Engineering
• /
• v.7 no.9
• /
• pp.325-334
• /
• 2018

Requirement traceability should be continuously maintained in software development and evolution. However, it is usually updated in practice in the quality assurance phase. The gap between "is" and "should" exists due to the fact that developers must invest considerable effort to update requirement traceability while being able to obtain only marginal benefit from the updated traceability. To close this gap, we propose a spreadsheet application that enables developers to flexibly change mappings in a requirement traceability matrix. In this way, developers can reduce their effort in updating the requirement traceability matrix, but still obtain the common form of a requirement traceability matrix on a spreadsheet. The proposed application maintains the mappings between two artifacts on each sheet so that, whenever an artifact item changes, developers can instantly insert the relevant mapping changes. Then, when developers desire the common form of a requirement traceability matrix, the proposed application calculates the mappings among several artifacts and creates the matrix. The application also checks traceability errors and calculates the metrics so that developers can understand the completeness of the matrix. To understand the applicability of the proposed approach, we conducted a case study, which shows that the proposed application can be applied to the real project and easily incorporate the mapping changes.

• Journal of Radiation Protection and Research
• /
• v.36 no.1
• /
• pp.28-34
• /
• 2011

The measurement-based verification for intensity modulated radiation therapy (IMRT) is a time-and labor-consuming procedure. Instead, this study aims to develop a MU fluence reconstruction method for IMRT QA. Total actual fluences from treatment planning system (TPS, Eclipse 8.6, Varian) were selected as a reference. Delivered leaf positions according to MU were extracted by the dynalog file generated after IMRT delivery. An in-house software was develop to reconstruct MU fluence from the acquired delivered leaf position data using MATLAB. We investigated five patient's plans delivered by both step-and-shoot IMRT and sliding window technologies. The total actual fluence was compared with the MU fluence reconstructed by using commercial software (Verisoft 3.1, PTW) and gamma analysis method (criteria: 3%/3 mm and 2%/1 mm). Gamma pass rates were $97.8{\pm}1.33$% and the reconstructed fluence was shown good agreement with RTP-based actual fluence. The fluence from step and shoot IMRT was shown slightly higher agreement with the actual fluence than that from sliding window IMRT. If moving from IMRT QA measurements toward independent computer calculations, the developed method can be used for IMRT QA. A point dose calculation method from reconstructed fluences is under development for the routine IMRT QA purpose.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.16 no.3
• /
• pp.249-258
• /
• 2010

This study seeks to improve NFRDI Serial Oceanographic observation (NSO) system which has been operated at current observation stations in the Korean Seas since 1961 and suggests the direction of NSO for practical use of Korean operational oceanographic system. For improvement, data handling by human after CTD (Conductivity-Temperature-Depth) observation on the deck, data transmission, data reception in the land station, and file storage into database need to be automated. Software development to execute QA/QC (Quality Assurance/Quality Control) of real-time oceanographic observation data and to transmit the data with conversion to appropriate format automatically will help to accomplish the automation. Inmarsat satellite telecommunication systems with which have already been equipped on board the current observation vessels can realize the real-time transmission of the data. For the near real-time data transmission, CDMA (Code Division Multiple Access) wireless telecommunication can provide efficient transmission in coastal area. Real-time QA/QC procedure after CTD observation will help to prevent errors which can be derived from various causes.

• Journal of radiological science and technology
• /
• v.21 no.1
• /
• pp.35-39
• /
• 1998

We analyzed image factors to determine the characteristic factors that need for intelligent replenishment system of the auto film processor. We processed the serial 300 sheets of radiographic films of chest phantom without replenishment of developing and fixation replenisher. We took the digital data by using film digitizer which scaned the films and automatically summed up the pixel values of the films. We analyzed characteristic curves, average gradients and relative speeds of individual film using densitometer and step densitometry. We also evaluated the pH of developer, fixer, and washer fluid with digital pH meter. Fixer residual rate and washing effect were measured by densitometer using the reagent methods. There was no significant reduction of the digital density numbers of the serial films without replenishment of developer and fixer. The average gradients were gradually decreased by 0.02 and relative speeds were also gradually decreased by 6.96% relative to initial standard step-densitometric measurement. The pHs of developer and fixer were reflected the inactivation of each fluid. The fixer residual rates and washing effects after processing each 25 sheets of films were in the normal range. We suggest that the digital data are not reliable due to limitation of the hardware and software of the film digitizer. We conclude that average gradient and relative speed which mean the film's contrast and sensitivity respectively are reliable factors for determining the need for the replenishment of the auto film processor. We need more study of simpler equations and programming for more intelligent replenishment system of the auto film processor.

• Progress in Medical Physics
• /
• v.26 no.4
• /
• pp.201-207
• /
• 2015

The new function of 3DVH software for dose calculation inside the patient undergoing TomoTherapy treatment by applying the measured data obtained by ArcCHECK was recently released. In this study, the dosimetric accuracy of 3DVH for the TomoTherapy DQA process was evaluated by the comparison of measured dose distribution with the dose calculated using 3DVH. The 2D diode detector array MapCHECK phantom was used for the TomoTherapy planning of virtual patient and for the measurement of the compared dose. The average pass rate of gamma evaluation between the measured dose in the MapCHECK phantom and the recalculated dose in 3DVH was $92.6{\pm}3.5%$, and the error was greater than the average pass rate, $99.0{\pm}1.2%$, in the gamma evaluation results with the dose calculated in TomoTherapy planning system. The error was also greater than that in the gamma evaluation results in the RapidArc analysis, which showed the average pass rate of $99.3{\pm}0.9%$. The evaluated accuracy of 3DVH software for TomoTherapy DQA process in this study seemed to have some uncertainty for the clinical use. It is recommended to perform a proper analysis before using the 3DVH software for dose recalculation of the patient in the TomoTherapy DQA process considering the initial application stage in clinical use.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.4
• /
• pp.77-83
• /
• 2019

With the increase in population, the number of such senior citizens is increasing day by day. These senior citizens have a variety of care needs, but there are not enough health workers to look after them. Ambient Assisted Living (AAL) aims at ensuring the safety and health quality of the older adults and extending the number of years the senior citizens can live independently in an environment of their own preference. AAL provides a system comprising of smart devices, medical sensors, wireless networks, computer and software applications for healthcare monitoring. AAL can be used for various purposes like preventing, curing, and improving wellness and health conditions of older adults. While information security and privacy are critical to providing assurance that users of AAL systems are protected, few studies take into account this feature. In this paper, we propose a secure and lightweight authentication scheme for the AAL systems. The proposed authentication scheme not only supports several important security requirements needed by the AAL systems, but can also withstand various types of attacks. Also, the security analysis results are presented to show the proposed authentication scheme is more secure and efficient rather than existing authentication schemes.