• 한국항공우주학회지
• /
• 제36권11호
• /
• pp.1056-1062
• /
• 2008

인공위성의 추력기에서 발생되는 플룸과 기저면의 상호 작용에 관한 연구를 직접모사법을 사용하여 실시하였다. 질소와 수소 분자의 충돌에 의한 회전-병진 에너지의 교환을 정확하게 모사하기 위하여 최근에 연구 되어진 질소와 수소 분자의 회전 에너지 이완 모델을 사용하였다. 추력기 플룸과 기저면의 상호 작용 해석을 위하여 플룸 분자들의 수밀도 분포와 회전, 병진 온도 분포, 열전달량, 압력 등에 대하여 다양한 운영 조건에 맞추어 해석을 실시하였다. 그 결과 기저면에서는 질소 분자보다 수소 분자의 분포가 매우 큰 것과, 분포하는 대부분의 수소 분자가 회전 에너지에 대해 비평형 상태로 분포 하는 것을 확인 하였다. 이는 수소 분자의 정확한 회전 에너지 이완 모델의 필요성을 보여주고 있는 결과이며, 본 연구의 경우 가장 최근의 수소의 회전 에너지에 관련된 모델을 사용함으로써 플룸과 기저면의 상호 작용 해석에 대한 정확도를 증진 시켰다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권6호
• /
• pp.753-760
• /
• 2007

For protection of the cylinder wall of the ball mill for grinding raw ore. the inner side of the cylinder is covered with rubber liner. The rubber is easily worn down because the rubber relatively soft compared with raw ore. So the rubber liner in the ball mill cylinder must be replaced almost every year and the cost for replacing rubber liner formidable. In this paper, for reducing or excluding the cost of replacing rubber liner the basalt liner is designed. The basalt materials are generally harder than raw ore and the basalt liner in the ball mill does not wear down and so it can be used almost permanently. The concave surfaces are made on the liner of the ball mill and the liner in the cylinder wall plays also the role of raising the steel balls mixed in the raw ore. The section profiles of the concave surface have an important effect on the performance of the ball mill. The deep concave grooves raise the steel balls to high levels and give the large potential energy to the steel balls impacting to the raw ore. But if the concave grooves are too deep. the steel balls raised too high by the concave grooves fly along the parabolic path and reach to the other side of cylinder wall and so the steel balls do not play the roles of grinding the raw ore. The forces acting to a steel ball in a concave groove of the cylinder liner are also analyzed in this paper. The formulas calculating the height and the impact point of the steel ball are introduced and presented. Based to these formulas, the optimum section profiles of the basalt liner are presented.

• 한국해양학회지:바다
• /
• 제7권3호
• /
• pp.148-156
• /
• 2002

서해 남부 함평만에서 해안선의 지형 특성과 해안절벽의 침식과정을 조사하기 위해 야외관찰과 정밀 측량을 실시하였다. 함평만 해안선은 급경사면 그리고 불안정한 토양층이나 연약한 풍화암층으로 이루어진 높이 l0m미만의 해안절벽(sea-cliff)들로 대부분 구성되며, 매우 활발한 침식을 받고있다. 톱날모양의 해안선 형태, 해빈 표면에 노출된 잔류풍화기반암 및 "Island Stack"등 독특한 해안선 지형 특성들이 활발한 해안침식 증거들로 나타난다. 함평만에서의 해안선 후퇴는 해안절벽 기저부의 침식 사태(landslide or mass wasting), 테일러스(talus)형성 그리고 테일러스의 침식(소멸)의 순차적 과정이 반복되어 나타난 결과로 해석된다. 본 연구에서 테일러스가 여름철에 침식.제거되는 현상은 정상적인 해양조건에서 일어나는 계절적 해수면 상승에 의한 것으로 판단된다. 이는 겨울철 폭풍과 함께 해안 침식의 또 다른 중요 요인으로 제시된다.요인으로 제시된다.

• Geomechanics and Engineering
• /
• 제8권5호
• /
• pp.663-674
• /
• 2015

Many seismically vulnerable regions in India and worldwide are located on deep soil deposits which extend to several hundred meters of depth. It has been well recognized that the earthquake shaking is altered by geological conditions at the location of building. As seismic waves propagates through uppermost layers of soil and rock, these layers serve as filter and they can increase the duration and amplitude of earthquake motion within narrow frequency bands. The amplification of these waves is largely controlled by mechanical properties of these layers, which are function of their stiffness and damping. Stiffness and damping are further influenced by soil type and thickness. In the current study, an attempt has been made to study the seismic site response of deep soils. Three hypothetical homogeneous soil models (e.g., soft soil, medium soil and hard soil) lying on bedrock are considered. Depth of half space is varied from 30 m to 2,000 m in this study. Controlled synthetic motions are used as input base motion. One dimensional equivalent linear ground response analyses are carried out using a computer package DEEPSOIL. Conventional approach of analysing up to 30 m depth has been found to be inadequate for deep soil sites. PGA values are observed to be higher for deeper soil profiles as compared to shallow soil profiles indicating that deeper soil profiles are more prone to liquefaction and other related seismic hazards under earthquake ground shaking. The study recommends to deal the deeper soil sections more carefully for estimating the amplification factors for seismic hazard assessment at the surface.

• Journal of Magnetics
• /
• 제20권3호
• /
• pp.229-240
• /
• 2015

In this study, nanocrystalline ferrite powders with the composition $Ni_{0.5}Zn_{0.5}Fe_2O_4$ were prepared by the autocombustion method. The obtained powders were sintered at $800^{\circ}C$, $900^{\circ}C$ and $1,000^{\circ}C$ for 4 h in air atmosphere. The as-prepared and the sintered powders were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, and magnetization studies. An increase in the crystallite size and a slight decrease in the lattice constant with sintering temperature were observed, whereas microstrain was observed to be negative for all the samples. Two significant absorption bands in the wave number range of the $400cm^{-1}$ to $600cm^{-1}$ have been observed in the FT-IR spectra for all samples which is the distinctive feature of the spinel ferrites. The force constants were found to vary with sintering temperature, suggesting a cation redistribution and modification in the unit cell of the spinel. The M-H loops indicate smaller coercivity, which is the typical nature of the soft ferrites. The observed variation in the saturation magnetization and coercivity with sintering temperature has been attributed to the role of surface, inhomogeneous cation distribution, and increase in the crystallite size.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제11권3호
• /
• pp.105-113
• /
• 2003

This study developed a practical two-microphone impedance tube method to measure the sound transmission loss of sound isolation materials without the use of an expensive reverberation room or an acoustic intensity probe. In order to evaluate the validation and applicability of the two-microphone impedance tube method, sound transmission losses for several sound isolation materials with different surface density and bending stiffness were measured, and the measured values were compared with the results from the reverberation room method and the theory. From the experimental results, it was found that the accuracy of sound transmission loss obtained by the impedance tube method depends upon the diameter size of the impedance tube (i.e., tested sample size). For sound isolation materials having relatively large bending stiffness such as acryl, wood, and aluminum plates, it was found that the impedance tube method proposed by this study was not valid to measure the sound transmission loss. On the other hand, for sound isolation materials having relatively small bending stiffness such as rubber, polyvinyl, and asphalt sheets, the comparisons of transmission loss between the results from the impedance tube method and the theory showed a good agreement within the range of the frequencies satisfying the normal incidence mass law. Therefore, the two-microphone impedance tube method proposed by this study can be an effective measurement method to evaluate the sound transmission loss for soft sound isolation sheets having relatively small bending stiffness.

• 한국의류학회지
• /
• 제26권2호
• /
• pp.193-204
• /
• 2002

Many fashion forecasting companies propose the fashion colors in every season. Modern fashion consumer respond to fashionable trends with utmost sensitivity. Therefore to satisfy the consumer with an trendy image, the fashion design must be found first, as image matters, followed by an analysis of each design element's effect on the total image composition. In previous studies of fashion image, has been discussed the positive correlation between fashion design elements of color, fabric, and form as the central issue. In this thesis, two of the fashion design elements, color and fabric are simultaneously considered to classify the image of fabric in fashion. For the color variables, 10 hues are selected from Munsell's system of color notation, and 12 tones from PCCS color notation., which are currently used in the domestic fashion industry. Texture variables used in this survey are classified by luster, prominence-depression of surface, thickness, and density of fabric. Graduate students from 20 to 50 years old and the specialists in fashion companies participated in the survey. The results of this survey are as follows: 1. The fashion fabric image is classified as 5 main images: 'elegant', 'comfortable', 'characteristic', 'light'and 'simple'. 2. The influence of hue, tone and texture is significant to the fashion fabric image. Following colors, yellow-red, red hues and light grayish, dark grayish tones convey the elegant image. The texture property for the elegant image is luster, thin and low density. Properties of fabric conveying the comfortable image are yellow-red and green-yellow hue, soft, light tones, matte and high density. Furthermore, hue turned out to be a insignificant variables for the unique image, whereas dark grayish, grayish tone, luster and prominent texture convey a unique image. For light image, properties of fabric are blue-green, purple hues, light, bright tones with thin, low density texture. Properties of fabric conveying the simple image are blue-green, purple-blue, green-yellow hues, and strong, vivid tones, with luster and flat texture.

• 한국해양학회지:바다
• /
• 제1권2호
• /
• pp.73-79
• /
• 1996

본 연구는 북동 태평양의 심해저 퇴적물에 서식하는 대형저서동물의 군집 구조와 수평적 및 수직적 분포양상을 보기 위해 1996년 5월에 수행되었다. 생물 시료는 25개 정점에서 box corer를 사용하여 채취된 퇴적물을 0.3 mm 망목의 체 로 걸러 채집하였다. 총 9개 동물문의 17개 분류군에 속하는 363개체의 저서동물이 출현하였고, 이들은 선형동물(30.0%), 유공충류(25.1%), 저서성 요각류(10.2%), Xenophyophorea(5.2%), 다모류(4.7%)순으로 우점하였다. 전형적인 중형동물 분류군 들을 제외하면 다모류가 가장 우점한 동물군이었다. 출현종의 수는 0.01 m$^{2}$ 당 평균 6종류였고, 서식밀도는 1,288개체/m$^{2}$ 로서 심해역으로는 밀도가 높았다. 퇴적물 깊이별 수직분포를 보면 표층에서 최대출현량을 보이고 깊이에 따 라 감소한다. 퇴적물 깊이 10 cm 층 이내에 전체 저서생물의 98% 이상이 출현 하였다.

• 천문학회보
• /
• 제42권1호
• /
• pp.54.1-54.1
• /
• 2017

The UKIRT Wide-field Infrared survey for Fe+(UWIFE) is an unbiased survey of the first Galactic quadrant, with narrow-band filter centered on $1.644{\mu}m$. This survey covers $7^{\circ}$ < l < $62^{\circ}$ and |b| < $1.5^{\circ}$, where active interaction of stars and interstellar medium is expected. With median seeing of 0.8 arcsec, 5 - sigma detection limit of 18.7 mag and surface brightness limit of $8.1{\times}10^{-20}W\;m^{-2}arcsec^{-2}$, this survey gives an opportunity to statistically study Galactic [Fe II] - emitting sources for the first time. In order to identify Ionized Fe Objects (IFOs) in survey area systematically, we conducted visual inspection and automatic detection simultaneously. Total of ~300 extended IFOs are identified, most of them are found out to be part of supernova remnants (SNRs), young stellar objects, HII regions and planetary nebulae. The majority of IFOs are new discoveries which reveal shocked structures in high-extinction region. Spatial distribution of IFOs suggest that they trace Galactic structure. As a part of spectroscopic follow-up, we observed SNR candidate IFO J183740.829-061452.41 with IGRINS (Immersion Grating Infrared Spectrograph, Yuk+2010), mounted on 2.7m Harlan Smith telescope. This unknown arc-like, 6'-long IFO is coincident with inner part of radio continuum loop G25.8+0.2, which has been known as HII region. However, interior of this radio shell is filled with diffuse soft X-ray emission, and possible association of hard X-ray pulsar / pulsar wind nebula makes the nature of the IFO unclear. The H and K-band 2D spectrum shows shock-ionized [Fe II] filaments, which is apart from photoionized HII filaments. In this presentation we present basic statistics of newly identified IFOs, as well as the follow-up study of IFO J183740.829-061452.41.

• 한국산림과학회지
• /
• 제101권4호
• /
• pp.558-566
• /
• 2012

이 연구는 채석장의 실태조사를 통하여 토석채취 후 합리적이고도 완벽한 복구를 실시하기 위한 기초 자료를 제공하기 위하여 전국의 18개 토석채취장을 대상으로 조사한 결과는 다음과 같다. 농어촌정비사업에 따른 토석 채취 후 산지복구지는 대부분 조경적 녹화가 이루어지고 있다. 또한 복구공사 후 유지관리가 이루어지지 않아 식재한 나무가 고사하거나 비탈면녹화가 제대로 되지 않아 여름철에는 강우에 의한 표층토양의 유실 및 붕괴로 이어지고, 복구녹화공사를 실시한 비탈면은 황폐화되고 있는 실정이다. 따라서 자연친화적이고 완벽한 복구녹화공사를 실시하기 위해서는 비탈면녹화를 실시하기 전에 현장의 토질특성, 지질특성 등에 대해서 조사하고 그곳에 적합한 복구공법에 대하여 면밀히 검토해야 한다. 아울러 계획된 복구공법의 적용에 있어서도 복구비를 절감할 수 있는 공법의 적용이 필요하다. 조사 결과 토석채취지의 경우 토질이 토사질 또는 리핑암, 풍화토가 대부분으로 이러한 지역은 복구녹화가 완벽하게 이루어질 수 있는 조건이 되므로 여기에 적용하는 공법도 가능하면 간단하면서도 복구녹화가 충분히 될 수 있는 공법의 선정이 중요하다. 아울러 복구녹화계획 및 검토시에는 반드시 산지복구를 전공으로 하는 전문가의 의견을 청취함으로써 그 지역에 가장 적합한 복구녹화공법의 선정 및 완벽한 복구녹화가 가능하게 될 것으로 사료된다.