• Journal of Sericultural and Entomological Science
• /
• v.47 no.1
• /
• pp.31-35
• /
• 2005

This study had done to find an easily-dyeing method for novices because the dyeing method of traditional indigo has not been general to the public so that only an expert could dye the fibers. The results are as the following. When the powders after burning the shell of cockle (tegillarca granosa) were added. pH of the solution was 12.35 The k/s value of 2.49 was the highest in the dye after dipping in the solution of indigo for 1-2 days and the k/s value was 3.10 when adding 20 g/l of the starch (55% corn-starchy products in Korean market) into the solution of indigo. In addtion, the k/s value was the highest when fermenting temperature was $30^{\circ}C$ and when the powders after burning the cockle shell were 4 g/l. There were no differences between water and lye of rice straw which had used for the ferment of indigo. The components of two dye which has traditionally made of the cockle shell and which has made of calcium hydroxide were all the same.

• Journal of dental hygiene science
• /
• v.20 no.1
• /
• pp.9-15
• /
• 2020

Background: Although the consumption of vitamin beverages has increased because of the recent interest in health and beauty, guidelines addressing appropriate consumption habits are lacking. Thus, the aim of this study was to investigate the erosive potential of several vitamin beverages and to propose guidelines for the appropriate intake of these drinks. Methods: Five vitamin beverages were selected after a pre-investigation of the current beverage market. Coca-Cola and mineral water were selected as the control beverages. The pH of the beverages was measured with a calibrated pH meter, and the titratable acidity (TA) was determined by using 1 M sodium hydroxide to reach pH 5.5 (TA5.5) and 7.0 (TA7.0). The screening method suggested by the International Organization for Standardization was used to measure pH variation (ΔpH) by using an under-saturated hydroxyapatite solution to determine the difference between the initial and final pH of the screening solution. All measurements were performed in triplicate. Results: All vitamin beverages tested in this study exhibited a low pH (2.53~2.99), similar to Coca-Cola, which is known to be a highly acidic beverage. The highest TA5.5 and TA7.0 values of the vitamin beverages were 7.03 ml and 8.81 ml, respectively. The largest change in pH determined by using the screening solution was found in Bacchus D (ΔpH 1.44±0.05). The mean ΔpH of the vitamin beverages was 1.12±0.29, which was higher than that of Coca-Cola (positive control, ΔpH 0.58±0.05). Conclusion: Vitamin beverages exhibited an erosive potential capable of damaging enamel surfaces. Therefore, the frequency of vitamin beverage intake should be limited, and individuals consuming these drinks should try to restore normal oral pH as quickly as possible.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.7 s.155
• /
• pp.1025-1033
• /
• 2006

Kenaf bast can be obtained by decortication of Kenaf stem. Kenaf fibers are much more rough than cotton fiber because they include impurities as pectin, lignin and hemicellulose besides cellulose. The purpose of this research is to investigate the distribution of kenaf fiber length and diameter during the processes of removing impurities. To remove pectin, kenaf bast was retted chemically. A half of the retted kenaf fiber bundle were scoured and bleached. The other half one were treated with $NaClO_2$ solution to remove lignin, and were treated with sodium hydroxide solution to remove hemicellulose. Four kinds of specimens that were obtained for investigating physical characteristics. Length and diameter of 100 fibers on each specimen was measured. The tensile strength of 100 fiber bundles were measured. And also the color values of them were measured with spectrocolorimeter. The length of retted kenaf fiber was 16.97cm. Then it decreased to 11.43cm after bleaching. Kenaf fiber bundles could be finer by chemical processes that remove non-cellulosic materials. The thickness of retted fiber was $132{\mu}m$. And after undergoing the chemical processes to remove non-cellulosic materials, the thickness of kenaf fiber became finer as $73{\mu}m$. Tensile strength of the retted kenaf fiber bundles was 11.37Mpa. The retted kenaf fiber lost their strength as 22.6% by bleaching and as 18.3% by treatment for removing lignin. The retted kenaf fiber showed low whiteness as 56.48 of L*value. After bleaching, the kenaf fibers have creamy white color and their whiteness got 90.02 of L*value. After the treatment for removing hemicellulose, the kenaf fibers also have creamy white color and their whiteness got L* value of 79.02.

• The Korean Journal of Mycology
• /
• v.26 no.4 s.87
• /
• pp.511-518
• /
• 1998

Anti-complementary assay for immuno-stimulating polysaccharide screening, human tumor colony-forming assay for discovering anti-tumor drugs, and toxic assay against mouse were performed to examine pharmacological activities of polysaccharides extracted from fruiting bodies of Jang-soo mushroom (Fomitella fraxinea). Hot water $(100^{\circ}C,\;FF-I)$, 1% ammonium oxalate solution $(80^{\circ}C,\;FF-II)$, and 5% sodium hydroxide solution $(80^{\circ}C,\;FF-III)$ were used for extraction of three polysaccharides from fruiting bodies of it. Anti-complementary activity of FF-I was more effective than the others. FF-I was further fractionated into three groups of polysaccharide by DEAE-Sephadex A25 column chromatography (FF-NP, FF-AP1, and FF-AP2). FF-AP1 showed not only the highest anti-complementary activity but also the growth-inhibitory activity against Snu-I (human stomach cancer cell) among 9 kinds of human tumor cell lines. But FF-AP2 exhibited its activity against Hep-2(larynx cancer) and KB(mouth epidermal cancer) cell lines at $500\;{\mu}g/ml$ although its anti-complementary activity was lower than it of FF-AP1. When FF-I was orally administrated to mice with dosage of 5000 mg/kg, no remarkable changes were observed in viewpoint of tissue-pathology.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.4
• /
• pp.388-396
• /
• 2009

In our study, the potential of okara as an ingredient of new bio-based adhesives was investigated for the production of fancy-veneered flooring boards. Okara was hydrolyzed by 1% sulfuric acid solution (AC) and 1% sodium hydroxide solution (AK). Phenol formaldehyde (PF) prepolymers were prepared as a cross-linker of okara hydrolyzates. Then, okara-based adhesive resins were formulated with 35% AC, 35% AK and 30% PF prepolymer on solid content basis. The adhesive resins were applied on high-density fiberboards (HDF) with the spread rate of $300g/m^2$. After that, oak fancy veneers are covered on the HDF, and then pressed with the pressure of $7kg/m^2$ at $120^{\circ}C$. The experimental variables were three mole ratios of formaldehyde to phenol (1.8, 2.1, 2.4), three assembly time (0, 10, 20 min), and two press time (90 sec, 120 sec), respectively. The fancy-veneered high-density fiberboards were tested by dry tensile strength, glueline failure by wetting and formaldehyde emission. Tensile strength of the boards exceeded the requirement of KS standard. The formaldehyde emissions were approached at the E0 level specified in KS standard. Based on these results, okara can be used as an ingredient of environmentally friendly adhesive resin systems for the production of flooring boards.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.11 no.4
• /
• pp.1798-1802
• /
• 1969

The experiment was carried out as one of the basic studies to improve the alkali-resistance of cement mortars and it was conducted to investigate some propetties of mortars relating to weight losses when exposed to 0.1 N salution of sodium hydroxide. The experiment and the results obtained are summarized as follow; 1. The specimens used in this experiment were made of 5 centi-meter cubes of mortar having such various ratios of mix by weight as 1 : 1, 1 : 3, 1 : 5, 1 : 7 and 1 : 10. 2. Physical tests included compressive strengths at 7 days, 28 days, 3 months, and 6 month, and 5 hour boiling absorption test. 3. In alkali test, every specimen was immersed into 0.1 N solutions of sodium hydroxide. The specimens exposed to the alkali solution were weighed to determine the weight losses of the alkail-corroded at one week interval for 7 week's exposure and the old alkali solutions were also changed to fresh solutions when weighed the weight losses by alkali attack at one week interval. 4. According to the alkail test after 7 week's exposure, no weight losses were observed on ratios of mix 1:1 and 1:3 and slight weight losses occurred on ratios of mix 1:5 and 1:7, but relatively large amount of weight losses were showed by 36.6 per-cent on ratios of mix 1:10. It was also found that the weight losses of the alkali-corroded were extremely lower than those of the acid-corroded at the some concentrations as 0.1 N of solutions. 5. In order to make better quality of alkali-resistant mortar it might recomend that a 1:7 mix or richemixes, use of small amount of mixing water for watertight, 20 per cent or less absorption by 5 hour boiling 1,600 kirogram per cubic meters or denser densities by absolute dry base are available for physical properties of mortar. It could conclude acid-resistant mortars were so high alkali-resistant, that it is expected to make and improve the acid-resistant mortars for getting rid of damages by alkali attack.

• Journal of agriculture & life science
• /
• v.46 no.6
• /
• pp.117-126
• /
• 2012

This study carried out on the manufacturing of pidan. The production of pidan can be one of solutions for over-produced eggs and stable egg price. For the alkali-pickling solution for manufacturing of Pidan, the tested concentration of NaOH and NaCl were respectively as 3, 5, 7% and 5, 10, 15, 20%, and examined every 2 days for 14days. According to the results, pH value of alkali-pickling solution was increased by the increment of NaOH concentration and the pickling period, and was decreased by the increment of NaCl concentration. The pH value of egg yolk was increased by the increment of NaOH concentration, but it was not significantly different by the NaCl concentration. By the increment of NaOH and NaCl concentrations, the alkali infiltration in egg yolk and egg white was accelerated. Furthermore, the weight change of the eggs in the alkali-solution has no effects on manufacturing of Pidan. Liquefied albumen showed significant differences by NaOH concentration rather than that of NaCl. There was no liquefied albumen for 14days at 3% of NaOH, but it was found between 11-12days at 5% and 8-10days at 7%, respectively. The pH values of egg white when it was liquefied albumen were between 11.8 and 12.0. Pidan was made by heat treatment after 6-7days dipped in the solution at the concentration of 7%, about 10days at 5%, and 12-14days at 3% of NaOH, respectively. Although, the period of manufacturing of Pidan was saved by the increment of NaOH concentration, liquefied albumen was accelerated and the food preference was decreased by ammonia odor. Therefore, the suitable concentration of NaOH is between 3 and 5%, and that of NaCl is between 5 and 10% due to the effect of salinity by the soaking period. Through this study, optimal pickling solution and dipping time for manufacturing of Pidan was figured out, and also find out that it can save a time about 15days for manufacturing of Pidan.

• The Korean Journal of Pesticide Science
• /
• v.18 no.4
• /
• pp.376-382
• /
• 2014

The soluble loess-sulfur mixture allowed standing to remove insoluble component materials for five weeks after manufacturing. We decreased the pH level of soluble loess-sulfur mixture at pH 1.0 modified with decreasing 25% sodium hydroxide than original content. The pH ranges of soluble loess-sulfur mixture solutions were adjusted to pH 5.0-pH 11.0 (pH 1 unit) with brown rice vinegar (pH 2.8). The pH of original loess-sulfur mixture was about pH 13 and damaged the foliar parts and young leaves of tomato after twice application. These stock solutions can be diluted 500:1 with tap water to make a 0.05% working solution and were sprayed two times with 7 days interval to the leaf and stem of tomato, which were spontaneously infected with E. cichoracearum. Control efficacy of powdery mildew ranged from 85% to 90% at 7 days after first application. After second application, each loess-sulfur mixture solutions adjusted pH level significantly suppressed the powdery mildew disease in tomato. Consequently, loess-sulfur complex adjusted pH level with brown rice vinegar was suggested to be low in acute toxicity at all different pH values and suggested to use an agent for control of tomato powdery mildew in organic farming.

• Korean journal of applied entomology
• /
• v.4
• /
• pp.47-50
• /
• 1965

Many of the chlorophenol derivatives are widely used as insecticides, herbicides and plant growth regulators. The function and use of these chemicals would be different according to the number of chlorine and their chemical structures. It was reported in this article that 1) Bis(trichlorophenoxy) ethane was synthesized with 2 mol-trichlorophenol and 1 moi-dibromoethane in 2 moi-Sodium hydroxide alcohol solution, and 3) the insecticidal activity of Bis(trichlorophenoxy) ethane was compared with Phenkapton, Tedion V-18, BHC, and DDT, on Citrus red mite, Bombix mori (Silk worm), and Daikon leaf beetle(Phaedon brassicae) 3) The toxicity of Bis(2, 4, 5-trichlorophenoxy) ethane and Bis(2, 4, 5-trichlorophenoxy) ethane was studied on mice. The following results were obtained. 1) Yield of Bis(2, 4, 5-trichlorophenoxy) ethane, $50.06\%$, m.p. $157-159^{\circ}C$, and yield of Bis(2,4, 6-trichlorophenoxy) ethane, $32.60\%$, m.p. $162-163^{\circ}C$. 2) Insecticidal activity of Bis(2, 4, 5-trichlorophenoxy) ethane to Citrus red mite is stronger than that of Tedion V-18, and weaker than that of Phenkapton. 3) Insecticidal activity of Bis(2, 4, 5-trichlorophenoxy) ethane to Bombix mori is weaker than those of BHC and DDT. 4) Insecticidal activity of Bis(2. 4, 5-trichlorophenoxy) ethane to Daikon leaf beetle proved to be ineffective. 5) Five rams of Bis(2, 4, 5-trichlorophenoxy) ethane and Bis(2, 4, 6-trichlorophenoxy) ethane pet kg of body weight respectively were given to mice orally, and none of the mouse was killed by it after a period of 72 hours. Therefore it seems that there is almost no toxicity.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.264-269
• /
• 2001

Large amounts of orange juice are produced in Japan every yea.. Accompanied by the production of orange juice, large amount of juice residues are also generated in nearly the same amounts with juice. Although, at present, some of these residues are marketed as a feed for cattle after drying and mixing with lime, the marketing price is lower than its production cost and the difference is paid by the consumers as a part of the price of orange juice. In the present work, we developed new innovative use of orange juice residue, a biomass waste, as adsorption gel for removing toxic heavy metals such as lead. arsenic, selenium and so on as well as radioactive elements such as uranium and thorium from environments. The major components of orange juice residue are cellulose. hemicellulose and pectin, which are converted into pectic. acid, an acidic polysaccharide, by means of saponification with concentrated sodium hydroxide solution. In the previous work, we found that crosslinked pectic acid gel strongly an selectively adsorbs lead over other metals such as zinc an copper. On the other hand. it is well known that polysaccharides such as cellulose can be easily phosphorylated and that phosphorylated polysaccharides have high affinity to uranium and thorium as well as some trivalent metals such as ferric iron and aluminum. Taking account of the noticeable characteristics of these polysaccharides, 2 types of adsorption gels were prepared from orange juice residue: one is the gel which was prepared by saponificating the residue followed by crosslinking with epichlorohydrin and another is that prepared by crosslinking the residue followed by phosphorylation. The former gel exhibited excellent adsorptive separation behavior for lead away from zinc owing to high content of pectic acid while the latter gel exhibited that for uranium and thorium. Both types of adsorption gels exhibited high affinity to ferric iron, which enables selective and strong adsorption for some toxic oxo-anions of arsenic (V and III), . selenium and so on via iron loaded on these gels. These results demonstrate that biomass wastes such as orange juice residue can be effectively utilized fer the purpose of removing toxic heavy or radioactive metals existing in trace or small amounts in environments.