• Fibers and Polymers
• /
• v.3 no.1
• /
• pp.1-7
• /
• 2002

Cellulose carbonate was prepared by the reaction of cellulose pulp and $CO_2$ with treatment reagents, such as aqueous $Zncl_2$ (20-40 wt%) solution, acetone or ethyl acetate, at -5-$0^{\circ}C$ and 30-40 bar ($CO_2$) for 2 hr. Among the treatment reagents, ethyl acetate was the most effective. Cellulose carbonate was dissolved in 10% sodium hydroxide solution containing zinc oxide up to 3 wt% at -5-$0^{\circ}C$. Intrinsic viscosities of raw cellulose and cellulose carbonate were measured with an Ubbelohde viscometer using 0.5 M cupriethylenediamine hydroxide (cuen) as a solvent at $20^{\circ}C$ according to ASTM D1795 method. The molecular weight of cellulose was rarely changed by carbonation. Solubility of cellulose carbonate was tested by optical microscopic observation, UV absorbance and viscosity measurement. Phase diagram of cellulose carbonate was obtained by combining the results of solubility evaluation. Maximum concentration of cellulose carbonate for soluble zone was increased with increasing zinc oxide content. Cellulose carbonate solution in good soluble zone was transparent and showed the lowest absorbance and the highest viscosity. The cellulose carbonate and its solution were stable in refrigerator (-$5^{\circ}C$ and atmospheric pressure).

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.9 no.2
• /
• pp.63-71
• /
• 2011

A large volume of uranium electrokinetic leachate has been generated during the electrokinetic decontamination to remove uranium from contaminated soil. The treatment technology for the reuse of the uranium leachate was developed. The concentration of uranium in the generated uranium leachate was 180 ppm and concentrations of Mg(II), K(I), Fe(II), and Al(III) ions ranged from 20 ppm to 1,210 ppm. The treatment process for uranium leachate consisted mainly of mixing and cohesion, precipitation, concentration, and filtration. In order to obtain the pH=11 of a precipitate solution, the calcium hydroxide needs to be 3.0g/100ml and the sodium hydroxide needed to be 2.7g/100ml. The results of several precipitation experiments showed that a mixture of NaOH+0.2g alum+0.15g magnetite was an optimal precipitant for filtration. The average particle size of precipitate with NaOH+alum+0.15g magnetite was $600\;{\mu}m$. Because the total value of metal concentrations in supernatant at pH=9 was the smallest, sodium hydroxide should be added with 0.2g alum and 0.15g magnetite for pH=9 of leachate.

• Geomechanics and Engineering
• /
• v.33 no.1
• /
• pp.29-40
• /
• 2023

Xanthan gum and starch compound biopolymer (XS), an environmentally friendly soil-binding material produced from natural resources, has been suggested as a slope protection material to enhance soil strength and erosion resistance. Insufficient wet strength and the consequent durability concerns remain, despite XS biopolymer-soil treatment showing high strength and erosion resistance in the dried state, even with a small dosage of soil mass. These concerns need to be solved to improve the field applicability and post-stability of this treatment. This study explored the utilization of an alkaline-based cation crosslinking method using calcium hydroxide and sodium hydroxide to induce non-thermal gelation, resulting in the enhancement of the wet strength and durability of biopolymer-treated soil. Laboratory experiments were conducted to assess the unconfined compressive strength and cyclic wetting-drying durability performance of the treated soil using a selected recipe based on a preliminary gel formation test. The results demonstrated that the uniformity of the gel structure and gelling time varied depending on the ratio of crosslinkers to biopolymer; consequently, the strength of the soil was affected. Subsequently, site soil treated with the recipe, which showed the best performance in indoor assessment, was implemented on the field slope at the bridge abutment via compaction and pressurized spraying methods to assess feasibility in field implementation. Moreover, the variation in surface soil hardness was monitored periodically for one year. Both slopes implemented by the two construction methods showed sufficient stability against detachment and scouring, with a higher soil hardness index than the natural slope for a year.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.1
• /
• pp.100-110
• /
• 2016

Alkaline Peroxide Mechanical Pulping (APMP) of Pinus densiflora harvested from domestic mountains was explored. APMP contributes to various advantages including pulp quality, elimination of the need for a bleaching process, and energy savings. Sequential treatment of impregnation of bleaching chemicals and refining not only overcome the concern of alkaline darkening of wood chips during chemical impregnation, but it also brightens the chips to the desired brightness levels suitable for writing and printing papers. APMP pulping from Pinus densiflora was greatly influenced by the dosage levels of hydrogen peroxide and sodium hydroxide. Alkaline peroxide treatment was carried out by applying one of three levels of hydrogen peroxide (1.5, 3, and 4.5% based on the oven-dried weight of the wood chips) and one of three levels of sodium hydroxide (1.5, 3, and 4.5% based on the oven-dried weight of the wood chips). Other chemicals including a peroxide stabilizers and metal chelation were constantly added for all treatments. Chemical treatment with a liquor-to-wood ration of 9:1 was carried out in a laboratory digestor. Compared to BTMP, APMP pulping displayed outstanding characteristics including the less requirement of refining energy, the better improvement of tensile strength, the more reduction of shives, and the greater increase of pulp brightness. In particular, when 4.5% of hydrogen peroxide with impregnation during 90 minutes was used, the brightness of APMP reached 64.9% ISO. Even though bulk of APMP was decreased with the increase of sodium hydroxide, a better and improved balance could be achieved between optical and strength properties. The spent liquor obtained from the discharge of the impregnation process at the dosage level of 4.5% hydrogen peroxide exhibited an equal level of residual peroxide with BTMP. In conclusion, APMP pulping showed successful results with Pinus densiflora due to its better response to the development of optical and physical properties compared to TMP pulping.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.3
• /
• pp.65-72
• /
• 2014

In this study, effects of alkali swelling at low concentration below 2 percent on properties of hardwood bleached kraft pulp (HwBKP) were elucidated. Swelling treatment of HwBKP was performed at various NaOH concentrations with/without beating. Then, the swelling characteristics of pulp fiber was evaluated by measuring the solvent retention values such as water retention value (WRV) and isopropyl alcohol retention value (LRV). It was found that fiber characteristics were influenced by NaOH swelling even at low alkali concentration and beating treatment as well. The values of WRV and LRV were decreased when the alkali concentration was increased. It is the result from the decreased acidic groups of pulp which were formed during beating. The acidic groups could be neutralized and then removed by alkali. The difference between WRV and LRV was decreased with increasing alkali concentration while the difference was increased when the alkali swollen pulp was beaten. In addition, the crystalline structure of HwBKP was almost not changed while the crystallinity was influenced by swelling treatment at a low alkali concentration.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.6
• /
• pp.1-7
• /
• 2014

Dissolving part of xylan and lignin in lignocellulosic biomass by base can be used as pretreatment technique. Cork oak was pretreated with sodium hydroxide solution and the pretreatment effects were evaluated with two critical factors - NaOH concentration and pretreatment temperature. Some of xylan and lignin were removed by base pretreatment. At $90^{\circ}C$ and 13% NaOH pretreatment, 22.0% of lignin and 78.8% of xylan removed by base treatment. Enzymatic hydrolysis of cork oak which was pretreated at higher temperature or concentration was further improved. After pretreatment of cork oak with 13% NaOH at $90^{\circ}C$, the conversion rate of cellulose to fermentable sugars were reached up to 91.3%. At ethanol fermentation with enzymatic hydrolysate from different pretreatment conditions, all enzymatic saccharification liquids were well fermented by Saccharomyces cerevisiae.

• Analytical Science and Technology
• /
• v.17 no.6
• /
• pp.527-531
• /
• 2004

Treatment with aqueous sodium hydroxide solution plays an important role to impart certain desirable properties - feel and luster on the surface of polyester fiber. In this process alkali wastewater contains disodium terephthalate, ethylene glycol (EG) and residual sodium hydroxide. In this paper we report a new method containing the pretreatments of derivatization with benzoyl chloride and solvent extraction using pentane. The calibration curve of EG determined by GC/MS-SIM shows a good linearity in the range of 0.1 to $25{\mu}g/mL$ having the standard deviation of ${\leq}8.7%$. The recovery and the detection limit of this method are 91.9-93.7% and $0.05{\mu}g/mL$ respectively.

• Textile Coloration and Finishing
• /
• v.2 no.3
• /
• pp.51-58
• /
• 1990

Cotton fabrics were mercerized in ammonia water, sodium hydroxide and mixture of ammonia/sodium hydroxide, slack and under tension. X-ray and infrared spectra analyses were used to measure crystallinity of treated cottons. Changes due to swelling, which took place in the accessible regions were determined by moisture regain and dye adsorption. In addition to that crease recovery was compared mutually, and breaking strength-elongation compared, too. Both ammonia water and caustic treatments produced changes in morphology (swollen fibers, decrease in convolutions) and in fine structure of the cellulose (increase accessibility as measured by increased moisture regain, dye adsorption). X-ray diffraction showed partial recrystallization into cellulose III lattic after tension treatment with ammonia water. Both reagents produced increased cotton elongation-at-break with slack mercerization, increased cotton breaking strength with tension mercerization, and increased moisture regain or dye adsorption with slack mercerization.

• Archives of Pharmacal Research
• /
• v.12 no.1
• /
• pp.8-11
• /
• 1989

Reaction of 6-(acetoxymethyl) -2,4-dichloropyrido [3,2-d] pyrimidine (I) with some nucleophiles was investigated. When I reacted with sodium azide afforded 2,4-diazido derivative (II). Treatment of II with sodium hydroxide underwent cyclization of the 2-azido group to tetrazolo, replacement of 4-azido group by hydroxide ion, and hydrolysis of 6-ace-foxy moiety to hydroxy methyl derivative (III). While, reaction of I with hydrazine hydrate resulted in the formation of 2,4 dihydrozino-6-hydroxymethyl derivative (lV).

• Restorative Dentistry and Endodontics
• /
• v.48 no.2
• /
• pp.17.1-17.8
• /
• 2023

The present report describes the endodontic treatment of an Oehlers type II dens invaginatus in a maxillary lateral incisor with 5 root canals, an extremely rare condition. Apical periodontitis and related symptoms were noted. Cone-beam computed tomography was used to aid the diagnosis, reveal tooth morphology, and assist in canal location. The pulp chamber was carefully accessed, and the root canals were explored under magnification. All root canals were prepared with an R25 Reciproc Blue system and sodium hypochlorite (NaOCl) irrigation. After initial preparation, a self-adjusting file (SAF) with NaOCl and ethylenediaminetetraacetic acid was used to complement the disinfection. Additionally, calcium hydroxide medication was applied. Vertical compaction was used to fill the canals with a calcium silicate-based endodontic sealer and gutta-percha. After 12 months, the patient exhibited healing of the periapical region, absence of symptoms, and normal dental function. In conclusion, this nonsurgical treatment protocol was successful in promoting the cure of apical periodontitis. Both complementary disinfection with an SAF and use of calcium hydroxide medication should be considered when choosing the best treatment approach for dens invaginatus with very complex anatomy.