• Journal of Sensor Science and Technology
• /
• v.23 no.1
• /
• pp.15-18
• /
• 2014

We present gas sensing performance based on $2{\times}2$ sensor array with four different elements ($TiO_2$, $SnO_2$, $WO_3$ and $In_2O_3$ thin films) fabricated by rf sputter. Each thin film was deposited onto the selected $SiO_2$/Si substrate with Pt interdigitated electrodes (IDEs) of $5{\mu}m$ spacing which were fabricated on a $SiO_2$/Si substrate using photolithography and dry etching. For 5 ppm $NO_2$ and 50 ppm CO, each thin film sensor has a different response to offers the distinguishable response pattern for different gas molecules. Compared with the conventional micro-fabrication technology, $2{\times}2$ sensor array with such remarkable response pattern will be open a new foundation for monolithic integration of high-performance chemoresistive sensors with simplicity in fabrication, low cost, high reliablity, and multifunctional smart sensors for environmental monitoring.

• Journal of Technologic Dentistry
• /
• v.30 no.2
• /
• pp.31-37
• /
• 2008

A variety of the porcelain fused to gold(PFG) have been developed to which porcelain can be fused. PFG alloys developed for this purposed have a high melting point and do not discolor when combined with porcelain. The design of the compositions of PFG is very important to esthetic restorative materials applying to porcelain. The purpose of this study is on the change of physical and mechanical characteristics in PFG 18K alloy by the small additional elements. Principal results are as follows. The high Au alloy containing 18Karat gold contents is respectively Au(75%), Pd(10%), Pt(4%), Ag(4%), In(2%), Sn(2%), Cu(2%), Ti(1%). These alloys are composed mainly of gold, platinum, silver and palladium with a few percent of the additional elements. By the addition of small amounts of elements such as In, Sn, Ti, the fine grain castings are produced in gold alloy and the small addition of platinum is very effective in increasing of hardness and strength. These gold alloys are representative of the changes to be expected as a result of heat treatment. These changes in strength and hardness values are sufficient to demonstrate a significant difference in performance between a as-casted and a heat-treated. These alloys have mechanical properties characteristics of Type and Type gold alloys. These alloys are useful to porcelain-metal restorations and dental laboratory. Also the porcelain fused to metal(PFM) alloys containing gold are commonly use for dental purposes in dental laboratory.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.369-370
• /
• 2005

LTCC (Low Temperature Cofired Ceramic) technology is one of technologies which can realize SIP (System-In-a-Package). In this paper realization of gas sensor using LTCC technology was described. In the conventional gas sensor structure, wire bonding method is generally used as an interconnection method whereas in the LTCC sensor structure, via was used for the interconnection. As sensing materials, $SnO_2$ was adopted. The effect of frit glass portion on the adhesion of the sensing material to the LTCC substrate and the electrical conductivity of the sensing material were analyzed. AgPd, PdO, Pt was added to the sensing material as an additive for improving the gas sensitivity and electrical conductivity and the effect of the amount of additives in the sensing material on the electrical conductivity was investigated. The effect of the amount of frit glass in the termination on the sensor performance, especially mechanical integrity, was considered and the crack initiation and propagation in the boundary between the sensing material and the termination was studied.

• Journal of Sensor Science and Technology
• /
• v.8 no.2
• /
• pp.115-123
• /
• 1999

A micro-gas sensor with heater and sensing electrode on the same plane was fabricated on phosphosilicate glass(PSG, 800nm)/$Si_3N_4$ (150nm) dielectric membrane. PSG film was provided by atmospheric pressure chemical vapor deposition(APCVD), and $Si_3N_4$ film by low pressure chemical vapor deposition (LPCVD). Total area of the fabricated device was $3.78{\times}3.78mm^2$. The area of diaphragm was $1.5{\times}1.5mm^2$, and that of the sensing layer was $0.24{\times}0.24mm^2$. Finite-element simulation was employed to estimate temperature distribution for a square-shaped diaphragm. The power consumption of Pt heater was about 85mW at $350^{\circ}C$. Tin thin films were deposited on the silicon substrate by thermal evaporation at room temperature and $232^{\circ}C$, and tin oxide films($SnO_2$) were prepared by thermal oxidation of the metallic tin films at $650^{\circ}C$ for 3 hours in oxygen ambient. The film analyses were carried out by SEM and XRD techniques. Effects of humidity and ambient temperature on the resistance of the sensing layer were found to be negligible. The fabricated micro-gas sensor exhibited high sensitivity to butane gas.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.51.3-51.3
• /
• 2010

Due to the recent public awareness of global warming and sustainable economic growth, there has been a growing interest in alternative clean energy sources. Hydrogen is considered as a clean fuel for the next generation. One of the technical challenges related to the use of hydrogen is safe monitoring of the hydrogen leak during separation, purification and transportation. For detecting various gases, chemiresistor-type gas sensors have been widely studied and used due to their well-established detection scheme and low cost. However, it is known that many of them have the limited sensitivity and slow response time, when used at low temperature conditions. In our work, a sensor based on Schottky barriers at the electrode/sensing material interface showed promising results that can be utilized for developing fast and highly sensitive gas sensors. Our hydrogen sensor was designed and fabricated based on indium oxide (In2O3)-doped tin oxide (SnO2) semiconductor nanoparticles with platinum (Pt) nanoclusters in combination with interdigitated electrodes. The sensor showed the sensitivity as high as $10^7%$ (Rair/Rgas) and the detection limit as low as 30 ppm. The sensor characteristics could be obtained via optimized materials synthesis route and sensor electrode design. Not only the contribution of electrical resistance from the film itself but also the interfacial effect was identified as an important factor that contribute significantly to the overall sensor characteristics. This promises the applicability of the developed sensor for monitoring hydrogen leak at room temperature.

• Journal of the Mineralogical Society of Korea
• /
• v.24 no.3
• /
• pp.245-252
• /
• 2011

콜롬비아는 안데스 산맥의 북단에 위치하며 NS 방향의 단층대를 기준으로 지질 환경의 차이가 크다. 단층대를 기준으로 동부지역은 원생대 변성암류와 이를 피복하는 고생대 변성퇴적암류가 주로 분포하며, 서부 지역은 고생대 퇴적암류, 중생대 화성암류, 제 3 기 화산양류 및 퇴적암류가 주로 분포한다. 지화학이상대는 6개 그룹으로 분류되며, 철 (Fe), 귀금속(Au, Ag, Pt), 기초금속(Cu, Pb, Zn), 희유금속(Sn, Cr, Co, Mn, Mo, Ni, Nb, W, V, Mg, Ti, Be, REE, Ga, Zr, Hf, Se, Te, Ta, Cd, In, Li 등) 빛 핵원료자원인 U 이상대로 구성된다. 콜롬비아의 주요 부존자원은 석탄, 니켈, 금 및 에메랄드이다. 에메랄드, 석탄 및 니켈은 세계적인 매장규모와 생산량을 보인다. 콜롬비아는 탐사가 거의 수행되지 않은 지역이 전 국토의 49%에 달해 광물부존 잠재성은 현재보다 크게 높을 것으로 보인다. 따라서 최근 콜롬비아와의 광물자원 협력이 강화되고 있는 시점에서 미탐사 지역을 대상한 공동탐사를 지화학 이상대가 확인된 지역을 중심으로 수행하여 신규광체를 확보하고, 광물자원 협력을 강화함으로써 공동개발 여건을 마련할 필요가 있다고 판단된다.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.3
• /
• pp.119-123
• /
• 2005

$0.10Pb(Sb_{1/2}Sn_{1/2})O_3-0.25PbTiO_3-0.65PbZrO_3$ specimens doped with $ MnO_2\;(0.18\;mol\%)$ and $Y_2O_3\;(0\~0.4\;wt\%)$ were fabricated by the mixed-oxide method. All specimens showed the typical XRD patterns of a perovskite polycrystalline structure and the lattice constant decreased with increasing amount of $Y_2O_3$. The relative dielectric constant and the dielectric loss of the specimens doped with $0.2\;wt\%\;Y_2O_3$ were 704 and 0.0201, respectively. The remanent polarization, the coercive field and the pyroelectric coefficient of the specimen doped with $0.2\;wt\%\;Y_2O_3$ were $10.88\times10^{-2}Cm^{-2},\;11.12\times10^2kVm^{-1}$ and $5.03\times10^{-4}Cm^{-2}K^{-1}$ at $25^{\circ}C$, respectively. The figures of merit, $F_V$ for the voltage responsivity and $F_D$ for the specific detectivity, of the specimen doped with $0.2\;wt\%\;Y_2O_3$ were the good values of $3.04\times10^{-2}\;m^2C^{-1}\;and\;1.50\times10^{-5}\;Pa^{-1/2}$, respectively.

• Journal of Sensor Science and Technology
• /
• v.18 no.3
• /
• pp.202-206
• /
• 2009

Flat type catalytic combustible hydrogen sensors were fabricated using platinum micro-heaters and sensing material pastes. The platinum micro-heater was formed on an alumina substrate by sputtering method. The paste for the sensing materials was prepared using ${\gamma}-Al_2O_3$ 30 wt%, $SnO_2$ 35 wt%, and Pd/Pt 30 wt% and coated on the platinum micro-heater. The sensing performances were tested for the prepared sensors with different substrate sizes. The micro catalytic combustible hydrogen sensors showed quick response time, high reliability, and good selectivity against various gases(CO, $C_3H_8,\;CH_4$) at low operating temperature of $156^{\circ}\C$.

• The Journal of Korean Academy of Prosthodontics
• /
• v.23 no.1
• /
• pp.39-59
• /
• 1985

The purpose of this study was to investigate how gap distances of 0.13mm, 0.15mm, 0.20mm, and 0.30mm affects solder joint strength from gold alloys and nickel-chromium base alloys and to examine the composition of solder gold, the solder joint of gold alloys and nickel-chromium base alloys. The tensile test specimens were prepared in the split stainless steel mold with a half dumbbell shape 2.5mm in diameter and l2mm in length. 6 pairs of specimens of each gap distance group of gold alloys and nickel-chromium base alloys were made and 48 pairs of all specimens were soldered with solder gold of 666 fineness. All soldered specimens were machined to a uniform diameter and then a tensile load was applied at a cross-head speed of 0.10mm/min using Instron Universal Testing Machine, Model 1115. The fractured specimens at solder gold of solder joint fracture with each gap distance of 0.13mm, 0.15mm, 0.20mm, and 0.30mm were examined under the Scanning Electron Microscope, JSM-35c and the composition of solder gold, the solder joint of gold alloys and nickel-chromium base alloys was analyzed by Electron Probe Micro Analyzer. The results of this study were obtained as follows: 1. In case of soldering of gold alloys, the tensile strength between gold alloys showed $37.33{\pm}2.52kg/mm^2$ at 0.13, $39.14{\pm}3.35kg/mm^2$ at 0.15mm, $43.76{\pm}2.97kg/mm^2$ at 0.20mm, and $49.18{\pm}4.60kg/mm^2$ at 0.30mm. There was statistically significant difference at each gap distance, and so the greater increase of gap distance showed the greater tensile strength. 2. In case of soldering of nickel-chromium base alloys, the tensile strength between nickel-chromium base alloys showed $34.84{\pm}4.26kg/mm^2$ at 0.13mm, $37.25{\pm}2.49kg/mm^2$ at 0.15mm, $42.91{\pm}4.32kg/mm^2$ at 0.20mm, and $46.93{\pm}4.21kg/mm^2$ at 0.30mm. There was not statistically significant difference only between 0.13mm and 0.15mm and bet ween 0.20 mm and 0.30mm, but generally the greater increase of gap distance showed the greater tensile strength. 3. The greater increase of gap distance shoed less porosities in solder gold at solder joint fracture. 4. In solder gold Au, Cu, Ag, Zn, and Sn were composed and Au and Cu were mostly distributed uniformly. 5. In solder joints of solder gold and gold alloys Au, Cu, Ag, Zn, and Sn were composed in solder gold and Au, Cu, Ag, Pt, and Pd were composed in gold alloys. Au and Cu of solder gold and gold alloys were mostly distributed uniformly and the diffusion of other elements except Pt and Pd around the solder joint was not almost found. In solder joints of solder gold and nickel-chromium base alloys Au, Cu, Ag, Zn, and Sn were composed in solder gold and Ni, Cr, and Al were composed in nickel-chromium base alloys. Au and Cu of solder gold and Ni and Cr of nickel-chromium base alloys were mostly distributed uniformly and the diffusion of other elements except Cr around the solder joint was not almost found.

• Journal of Gifted/Talented Education
• /
• v.20 no.3
• /
• pp.767-788
• /
• 2010

The purpose of this study was to examine emotional characteristics and to provide information about the special needs of counselling of science gifted in Korea. The subjects were 143 science gifted high school students in Busan that had been tested MBTI and MMPI-A. The distribution map of MBTI type was examined and Pearson's correlation, one-way ANOVA, multiple regression analysis were used to analyse the relation between MBTI and MMPI-A through SPSS 17.0 program. The results showed as follows: first, ENTP, INTP, ISTJ personality types and NT temperament type were the most frequently from the distribution map of MBTI type. Second, F1, F2, F, Hs, D, Pt, Sc and Si scales of MMPI-A were positively related to I preference of MBTI and K and Ma scales of MMPI-A were significantly related to E preference of MBTI from Pearson's correlation. Third, The score of IN group was significantly more high in F1, Hs, D, SC and Si scales of MMPI-A than other group in the relation between two combination preferences of MBTI and scale of MMPI-A. The following results were same; IS group in D, Si scales, EN group in Ma scale, IT group in Hs, D, Pt and S scales, IF group in VRIN, D and Si scales, ET in Ma scale, IJ group in D and Si, IP group in F1, F, Hs, D, Hy, Pt, Sc and Si scales, EJ and EP groups in Ma scale. Finally, I preference of MBTI by F1, F2, F, Hs, D, Pt, Sc and Si scales of MMPI-A, E preference of MBTI by Ma scale of MMPI-A, F preference of MBTI by K scale of MMPI-A and P preference of MBTI by Hy scale of MMPI-A were significantly predicted from multiple regression analysis. Limitations of the current study and the suggestions for further research were offered.