• 한국전기전자재료학회논문지
• /
• 제22권11호
• /
• pp.961-968
• /
• 2009

In this work, transparent conductive oxide(TCO) films such as $In_2O_3-SnO_2$(ITO) and $In_2O_3-ZnO$(IZO) were prepared on polyethylene naphthalene(PEN) and glass substrates by using rf-magnetron sputtering system. The TCO films deposited on PEN substrate show very poor conductivity as compared to that of the TCO films deposited on glass substrates. From the results of the residual gas analysis(RGA) test, this poor stability of plastic substrate is presumed to be caused by the deteriorated adhesion between the TCO films and the plastic substrate due to outgassing from the plastic substrate during deposition of TCO films. From our experiment, it is found that the vaporization of some defects in the plastic substrates deteriorate the adhesion of the TCO films to the plastic substrate, because the most plastic substrates containing the water vapor and/or other adsorbed particles such as organic solvents. Mixing of these gases vaporized in the sputtering process will also affect the electrical property of the deposited TCO films. Inorganic thin composite $(SiO_2)_{40}(ZnO)_{60}$ film as a gas barrier layer is coated on the PEN substrate to protecting the diffusion of vapors from the substrate, so that the TCO films with an improved quality can be obtained.

• 센서학회지
• /
• 제33권1호
• /
• pp.40-47
• /
• 2024

The creation of vertically aligned one-dimensional (1D) nanostructures through the decoration of n-type tin oxide (SnO₂) on p-type chromium oxide (Cr₂O₃) constitutes an effective strategy for enhancing gas sensing performance. These heterostructures are deposited in multiple stages using a glancing angle deposition technique with an electron beam evaporator, resulting in a reduction in the surface porosity of the nanorods as SnO₂ is incorporated. In comparison to Cr₂O₃ films, the bare Cr₂O₃ nanorods exhibits a response 3.3 times greater to 50 ppm H₂S at 300℃, while the SnO₂-decorated Cr₂O₃ nanorods demonstrate an eleven-fold increase in response. Furthermore, when subjected to various gases (CH₄, H₂S, CO₂, H₂), a notable selectivity toward H₂S is observed. This study paves the way for the development of p-type semiconductor sensors with heightened selectivity and sensitivity towards H₂S, thus advancing the prospects of gas sensor technology.

• Transactions on Electrical and Electronic Materials
• /
• 제16권2호
• /
• pp.99-102
• /
• 2015

Thin film transistors (TFTs) with amorphous 2 wt% silicon-doped zinc tin oxide (a-2SZTO) channel layer were fabricated using an RF magnetron sputtering system, and the effect of post-annealing treatment time on the structural and electrical properties of a-2SZTO systems was investigated. It is well known that Si can effectively reduce the generation of oxygen vacancies. However, it is interesting to note that prolonged annealing could have a bad effect on the roughness of a-2SZTO systems, since the roughness of a-2SZTO thin films increases in proportion to the thermal annealing treatment time. Thermal annealing can control the electrical characteristics of amorphous oxide semiconductor (AOS) TFTs. It was observed herein that prolonged annealing treatment can cause bumpy roughness, which led to increase of the contact resistance between the electrode and channel. Thus, it was confirmed that deterioration of the electrical characteristics could occur due to prolonged annealing. The longer annealing time also decreased the field effect mobility. The a-2SZTO TFTs annealed at 500℃ for 2 hours displayed the mobility of 2.17 cm²/Vs. As the electrical characteristics of a-2SZTO annealed at a fixed temperature for long periods were deteriorated, careful optimization of the annealing conditions for a-2SZTO, in terms of time, should be carried out to achieve better performance.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.307-310
• /
• 2000

Antimony doped tin oxide (ATO) thin films were deposited at room temperature by ion-beam sputter deposition (IBSD) technique in oxidizing atmosphere utilizing Sb and Sn metal targets. Effect of Sb doping concentration, film thickness and heat treatment on electrical and optical properties was investigated. The thickness of as-deposited films was controlled approximately to $1500{\AA}$ or $2000{\AA}$, and Sb concentration to 10.8 and 14.9 wt%, as determined by SEM and XPS analyses. Heat treatment was performed at the temperature from $400^{\circ}C$ to $600^{\circ}C$ in flowing $O_2$ or forming gas. The resulting ATO films showed widely changing electrical resistivity and optical transmittance values in the visible spectrum depending on the composition, thickness and firing condition.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.206.2-206.2
• /
• 2015

최근 비정질 산화물 반도체 thin film transistor(TFT)는 차세대 투명 디스플레이로 많은 관심을 받고 있으며 활발한 연구가 진행되고 있다. 산화물 반도체 TFT는 기존의 비정질 실리콘 반도체에 비하여 큰 on/off 전류비, 높은 이동도 그리고 낮은 구동전압으로 인하여 차세대 투명 디스플레이 산업에 적용 가능하다는 장점이 있다. 한편 기존의 sputter나 evaporator를 이용한 증착 방식은 우수한 막의 특성에도 불구하고 많은 시간과 제작비용이 든다는 단점을 가지고 있다. 따라서 본 연구에서는 별도의 고진공 시스템이 필요하지 않을 뿐만 아니라 대면적화에도 유리한 용액공정 방식을 이용하여 박막 트렌지스터를 제작하였으며 thermal 열처리와 microwave 열처리 방식에 따른 전기적 특성을 비교 및 분석하고 각 열처리 방식의 열처리 온도 및 조건을 최적화 하였다. 제작된 박막 트렌지스터는 p-type bulk silicon 위에 산화막이 100 nm 형성된 기판에 spin coater을 이용하여 Al-Zn-Sn-O 박막을 형성하였다. 연속해서 photolithography 공정과 BOE (30:1) 습식 식각 과정을 이용해 활성화 영역을 형성하여 소자를 제작하였다. 제작 된 소자는 Pseudo-MOS FET구조이며, 프로브 탐침을 증착 된 채널층 표면에 직접 접촉시켜 소스와 드레인 역할을 대체하여 동작시킬 수 있어 전기적 특성평가가 용이하다는 장점을 가지고 있다. 그 결과, microwave를 통해 열처리한 소자는 100oC 이하의 낮은 열처리 온도에도 불구하고 furnace를 이용하여 열처리한 소자와 비교하여 subthreshold swing(SS), Ion/off ratio, field-effectmobility 등이 개선되는 것을 확인하였다. 따라서, microwave 열처리 공정은 향후 저온 공정을 요구하는 MOSFET 제작 시의 훌륭한 대안으로 사용 될 것으로 기대된다.

• Transactions on Electrical and Electronic Materials
• /
• 제16권6호
• /
• pp.303-307
• /
• 2015

Multilayered films of ITO (In₂O₃:SnO₂ = 9:1)/SiO₂ were deposited on soda-lime glass by RF/DC magnetron sputtering at 500℃ to improve the energy conversion efficiency of dye-sensitized solar cells (DSSCs). The light absorption of the dye was improved by decrease in light reflectance from the surface of the DSSCs by using an ITO film. In order to estimate the optical characteristics and compare them with experimental results, a simulation program named EMP (essential macleod program) was used. EMP results revealed that the multilayered thin films showed high transmittance (approximate average transmittance of 79%) by adjusting the SiO₂ layer thickness. XRD results revealed that the ITO and TiO₂ films exhibited a crystalline phase with (400) and (101) preferred orientations at 2 θ = 26.24° and 35.18°, respectively. The photocurrent-voltage (I-V) characteristics of the DSSCs were measured under AM 1.5 and 100 mW/cm² (1 sun) by using a solar simulator. The DSSC fabricated on the ITO film with a 0.1-nm-thick SiO₂ film showed a Voc of 0.697 V, J_sc of 10.596 mA/cm² , FF of 66.423, and calculated power conversion efficiency (η_AM1.5) of 5.259%, which was the maximum value observed in this study.

• 한국세라믹학회지
• /
• 제38권11호
• /
• pp.973-979
• /
• 2001

Sn을 도핑한 In$_2$O$_3$(ITO) 박막을 R.F. 마그네트론 반응성 스퍼터링법에 의해서 증착하였다. 동일한 마그네트론 스퍼터링 조건에서 증착위치에 따른 ITO 박막의 저항, 자유 전하 농도 및 이동도 전기적 특성을 조사하였다. 동일한 마그네트론 스퍼터링 조건임에도 불구하고, ITO 박막의 전기적 특성은 증착위치에 따라 불균질성을 나타내었다. 타겟의 중심에 위치한 기판위에 증착된 ITO 박막의 저항은 최소 값인 2~4$\times$$10^{-4}$ $\Omega$.cm인 반면, 중심에서 멀어질수록 박막의 전기 저항은 대칭적으로 증가하였다. ITO 박막의 밀도 측정 결과도 중심에서 이론 밀도 값의 97%에 해당하는 7.0g/$cm^3$를 나타내나, 위치가 중심에서 멀어질수록 박막의 밀도가 대칭적으로 감소하였다. ITO 박막에서 이동도와 전도도는 밀도에 직접적으로 영향을 받는 것이 실험적으로 확인되었다. ITO 박막의 밀도가 7.0g/$cm^3$(이론 밀도의 97%)인 경우, 자유행정거리와 입자크기(=주상의 직경)가 동일한 값을 가지나, 밀도가 이 보다 감소하면 자유행정거리와 입자크기의 차이는 더욱 증가하였다. 이 결과는 ITO 박막의 밀도가 7.0g/$cm^3$인 경우는 입계가 자유 전자의 전도에 중요한 산란 원으로 작용하는 반면, 그 외의 경우는 결정 내의 공격자점, 공공, 기공 등이 다른 산란 원으로 작용하고 있다는 것을 나타낸다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.101-104
• /
• 1998

A new planar-type micro gas sensor was designed and fabricated on silicon substrate and the operating characteristics of the sensor were investigated. The thin sensitive film of the sensor was fabricated by spin-coating of the SnO$_2$ sol solution which was synthesized by hydrothermal method. The spin-coating method for preparation of sensing layer was adopted to improve the long-term stability of the fabricated sensing film instead of physical methods such as rf sputtering and thermal evaporation. The fabricated microsensor showed a fairly good sensing performance for CO gas in air at 250$^{\circ}C$ The sensitivity(S=Ra/Rg) was shown to be about 5 to 2000ppm CO with heating power of 50mW.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.168-168
• /
• 2010

Transparent conduction oxides (TCOs) films is extensively reported for optoelectronic devices application such as touch panels, solar cells, liquid crystal displays (LCDs), and organic light emitting diodes(OLEDs). Among the many TCO film, indium tin oxide(ITO) is in great demand due to the growth of flat panel display industry. However, indium is not only high cost but also its deposits dwindling. Therefore, many studies are being done on the transparent conductive oxides(TCOs). We fabricated a target of IZTO(In2O3:ZnO:SnO2=70:15:15 wt.%) reduced indium. Then, IZTO thin films were deposited on glass substrates by pulsed DC magnetron sputtering with various oxygen flow ratio. The substrate temperature was fixed at the room temperature. We investigated the electrical, optical, structural properties of IZTO thin films. The electrical properties of IZTO thin films were dependent on the oxygen partial pressure. As a result, the most excellent properties of IZTO thin films were obtained at the 3% of oxygen flow rate with the low resistivity of $7.236{\times}10^{-4}{\Omega}cm$. And also the optical properties of IZTO thin films were shown the good transmittance over 80%. These IZTO thin films were used to fabricated organic light emitting diodes(OLEDs) as anode and the device performances studied. The OLED with an IZTO anode deposited at optimized deposition condition showed good brightness properties. Therefore, IZTO has utility value of TCO electrode although it reduced indium and we expect it is possible for the IZTO to apply to flexible display due to the low processing temperature.

• 열처리공학회지
• /
• 제23권5호
• /
• pp.245-248
• /
• 2010

Sn doped $In_2O_3$ (ITO) and ITO/Ni/ITO (INI) multilayer films were deposited on the glass substrates with a reactive magnetron sputtering system without intentional substrate heating and then the influence of the Ni interlayer on the methanol gas sensitivity of ITO and INI film sensors were investigated. Although both ITO and INI film sensors have the same thickness of 100 nm, INI sensors have a sandwich structure of ITO 50 nm/Ni 5 nm/ITO 45 nm. The changes in the gas sensitivity of the film sensors caused by methanol gas ranging from 100 to 1000 ppm were measured. It is observed that the INI film sensors show the higher sensitivity than that of the ITO single layer sensors. Finally, it can be concluded that the INI film sensor have the potential to be used as improved methanol gas sensors.