• 한국표면공학회지
• /
• 제41권5호
• /
• pp.214-219
• /
• 2008

Indium tin oxide (ITO) films were deposited on PET substrate by RF superimposed DC magnetron sputtering using ITO (doped with 10 wt% $SnO_2$) target. Substrate temperature was maintained below $750^{\circ}C$ without intentionally substrate heating during the deposition. The discharge voltage of DC power supply was decreased from 280 V to 100 V when superimposed RF power was increased from 0 W to 150 W. The electrical properties of the ITO films were improved with increasing of superimposed RF power. In the result of cyclic bending test, relatively high mechanical property was obtained for the ITO film deposited with RF power of 75 W under DC current of 0.75 A which could be attributed to the decrease of internal stress caused by decrease in both deposition rate and plasma impedance.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.276.1-276.1
• /
• 2016

본 연구에서는 차세대 유연 투명 히터 (Flexible and transparent heater) 제작을 위한 ATO 나노입자-은 네트워크 하이브리드 투명 전극의 특성을 연구하였다. 최적화된 은 네트워크 (Self-assembled Ag network) 투명 전극 상에 20-30 nm의 직경을 가지는 ATO (Sb-doped $SnO_2$) 나노입자를 스프레이 방식으로 상압, 상온에서 코팅하여 인쇄형 ATO-은 네트워크 하이브리드 투명 전극을 구현하였다. 스프레이로 코팅된 투명 ATO 나노 입자는 은 네트워크 전극의 빈 공간을 매워 줌으로써 은 네트워크 간의 연결성 및 표면 조도를 낮춰주어 유연 투명 히터 작동 시 전류의 집중 현상을 막아줄 수 있다. ATO-은 네트워크 하이브리드 투명 전극의 최적화를 위해 스프레이 횟수에 따른 하이브리드 투명 전극의 전기적, 광학적, 표면 특성을 분석하였으며, 최적의 조건에서 14 Ohm/square의 면저항과 66%의 투과도를 가지는 하이브리드 투명 전극을 구현하였다. 또한 FESEM 분석을 통해 ATO-은 네트워크 하이브리드 전극의 표면 및 계면 구조를 연구하고 ATO 코팅이 은 네트워크 전극의 특성에 미치는 영향을 규명하였다. 최적화된 ATO-은 네트워크 하이브리드 투명 전극을 이용하여 유연 투명 히터를 제작하고 전압에 따른 히터의 온도의 변화를 측정하여 차세대 유연 투명 히터용 투명 전극으로 인쇄기반 ATO-은 네트워크 하이브리드 투명 전극의 가능성을 확인하였다.

• 한국생활과학회지
• /
• 제11권4호
• /
• pp.391-400
• /
• 2002

This study was intended to research the dyeing with natural walnut hull extracts over cotton, flax, rayon, wool, nylon and silk. We studied the dyeing conditions and mordant effect, and observed dyeability. The result are as follows: 1. In the dyeability with natural walnut hull extracts, protein and polyamide fiber has more dye uptake rather than cellulose fiber. 2. The optimum condition in the dyeing with natural walnut hull extracts was at $90^{\circ}C$, 12%(o.w.b) concentration in 90 mins. 3. In the case of the dyeability by repeated dyeing number, the dyeability of good dyeability fiber is improved in the first or second dyeing, but that of bad dyebality fiber is improved when it is dyed more repeatedly. 4. In the dyeablity treated with mordants, Al, Sn, and Mg don't have any differences, but Cu and Fe have some difference. The color of Fe mordant is green and the color of Cu mordant is blue. 5. In the case of the color fastness with mordant treatment, nylon is better than silk and wool in color fastness to washing but silk is better than nylon and wool in color fastness to light.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권4호
• /
• pp.139-143
• /
• 2005

For application of carbon nano-tube (CNT) as a counter electrode materials of dye-sensitized solar cell (DSSC), the electrochemical behavior of CNT electrode was studied, employing cyclic-voltammetry (C-V) and impedance spectroscopy. Fabrication of CNT-paste and formation of CNT-counter electrode for characteristic measurement have been carried out using ball-milling and doctor blade process, respectively. Unit cell for measurements was assembled using Pt electrode, CNT electrode, and iodine-embedded electrolyte. Field emission-scanning electron microscopy (FE-SEM) was used for structural investigation of CNT powder and electrode. Sheet resistance of electrode was measured with 4-point probe method. Electrochemical properties of electrode, C-V and impedance spectrum, were studied, employing potentiogalvanostat (EG&G 273A) and lock in amplifier (EG&G 5210). As a results, the sheet resistance of CNT electrode is almost similar to that of F-doped SnO2 (FTO) coated glass substrate as approximately 10 ohm/sq. From C-V and impedance spectroscopy measurements, it was found that CNT electrode has high reaction rate and low interface reaction resistance between CNT surface and electrolyte. These results provides that CNT electrode were superior to that of conventional Pt electrode. Particularly, the reaction rate in the CNT electrode is about thrice high than Pt electrode. Therefore. CNT electrode is to be good candidate material for counter electrode in DSSC.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.151-154
• /
• 2004

화합물 반도체 단일 나노선의 에칭 효과를 보기 위하여 에칭 용액과 시간을 달리하면서 전류-전압 특성을 측정하였다. 측정을 위한 단일 나노선 소자는 Electron beam lithography를 이용하여 전극을 top contact 방식으로 만들었다. 에칭은 식각과정에서 현상된 상태의 패턴에서 수행하며 금속 전극과 나노선 접합 부분만을 에칭 하였다. 에칭용액은 Buffered Oxide Etchant(BOE)을 이용하였으며 에칭 시간은 수 십초에서 수 십분까지 다양하게 하였다. 전압-전류 특성 측정결과에서 에칭 용액과 에칭 시간에 따라 전류가 증가하는 것을 확인 할 수 있었다. 이러한 효과는 나노선 외곽에 비정질 산화층의 제거 효과로 인한 것으로 설명할 수 있다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.874-877
• /
• 2004

We carried out this subject to observe electrochemical properties of 1,2-dioleoyl-sn- glycero-3-phosphocholine(DOPC) mixed with fatty acid containing azobenzene group by using cyclic voltammetry with a three-electrode system, An Ag/AgCl reference electrode, a platinum wire counter electrode and LB film-coated ITO working electrode in $NaClO_4$ solution. We investigated the photoisomerization and electrochemical property of the organic ultra thin film of fatty acid containing azobenzene was prepared on the hydrophilic ITO(idium tin oxide) glass plate by LB method. As a result, the absorption spectra of BASH and DOPC of mixture LB films was induced to photoisomerization by alternating irradiation of ultraviolet and visible light. A measuring range was reduced from initial potential to -1350mV, continuously oxidized to 1650 mV and measured to the initial point. The scan rate were 50, 100, 150 and 200 mV/s. As a results, LB films of BASH-DMPC appeared reversible process caused by the reduction-oxidation current from the cyclic voltammogram.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.307-310
• /
• 2000

Antimony doped tin oxide (ATO) thin films were deposited at room temperature by ion-beam sputter deposition (IBSD) technique in oxidizing atmosphere utilizing Sb and Sn metal targets. Effect of Sb doping concentration, film thickness and heat treatment on electrical and optical properties was investigated. The thickness of as-deposited films was controlled approximately to $1500{\AA}$ or $2000{\AA}$, and Sb concentration to 10.8 and 14.9 wt%, as determined by SEM and XPS analyses. Heat treatment was performed at the temperature from $400^{\circ}C$ to $600^{\circ}C$ in flowing $O_2$ or forming gas. The resulting ATO films showed widely changing electrical resistivity and optical transmittance values in the visible spectrum depending on the composition, thickness and firing condition.

• 동력기계공학회지
• /
• 제17권1호
• /
• pp.104-109
• /
• 2013

Tin and Tinoxide nanoparticles were prepared by arc-discharge nanopowder process. The negative electrode were fabricated using Tin and Tinoxide nanopower. The microstructure and electrochemistry properties were investigated and compared between Tin and Tinoxide. The oxidation film has microstructure of core/shell type and the shell which was attached around Tin nanoparticle consisted of amorphous $SnO_2$. The shape of Tinoxide nanoparticles was formed with irregular shape in comparison with Tin particle. Initial discharge capcity of Tinoxide electrode possesed about 1000mAh/g, which is about 320mAh/g higher than Tin electrode. Irreversible capacity of Tin electrode is much higher than Tinoxide. The cycle performance of Tinoxide electrode was indicated that is batter than Tin. The Tin negative electrode lost most of capacity after 4 cycle but Tinoxide electrode still retained the capacity. The Tinoxide does show some promise as Li-ion battery anode due to their large reversible capacity at low potentials.

• Journal of Oral Medicine and Pain
• /
• 제26권4호
• /
• pp.369-376
• /
• 2001

Objectives : The purposes of the study was to evaluate cephalometric characteristics in snorers and patients with obstructive sleep apnea (OSA) and to see any relationships between the cephalometric measurements and respiratory disturbance indices (RDI). Materials and Methods : Twelve snoring patients, 11 patients with OSA, and 10 normal subjects were included for the study. After taking a screening sleep study for a night to obtain RDI, $SaO_2$, and snoring index, a detailed cephalometric analysis was conducted to obtain SNA, SNB, SN-MP, IAS, MAS, SPAS, SAAS, Mn-H, and PNS-P. All the data were compared between groups. For a group including 12 snoring patients and 11 OSA patients, correlation coefficients were calculated between respiratory disturbance index and each item of cephalometric measurements. Results : The mandible and the maxilla are retropositioned. The oropharyngeal and hypopharyngeal airway is reduced in area and is a factor that could produce or enhance OSA symptoms. The hyoid bone is displaced inferiorly. The soft palate is significantly elongated. Conclusions : These data suggest that cephalometric evaluation could be useful to evaluate snoring and OSA patients, and to assist with the planning treatment for improvement of upper airway patency.

• 한국재료학회지
• /
• 제9권5호
• /
• pp.533-537
• /
• 1999

ATO(Sb doped $SnO_2$) thin films whose thicknesses were 600, 1100 and $2100\AA$ were prepared by DC magnetron sputtering method. They showed the lowest resistivity at DC sputtering power 0.24kW and had lower resistivity with increasing thickness. The power dependence of resistivity among ATO thin films was also different with thickness. The increase of carrier concentration in ATO thin films was responsible for the decrease of resistivity with thickness increase. ATO thin films which were prepared at 30sccm oxygen flow rate showed a great change of sheet resistance under 1M HCl solution. The investigation of SAM(Scanning Auger Microprobe) revealed that oxygen atomic percentage on the surface of ATO thin films was changed. The decrease of sheet resistance also occurred when ATO thin films, prepared at 30sccm oxygen flow rate, were exposed to air for a long period of time. For this reason, it was considered that the desorption of oxygen on ATO surface was accelerated by HCl.