• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2001.11a
• /
• pp.141-145
• /
• 2001

Sn-3.5Ag 무연 솔더에 Cu를 첨가한 3원계 합금을 만든 후 압연과 열처리한 후 크리프 특성을 연구하였다. 모든 솔더 합금에서 1차 크리프는 거의 관찰되지 않았으며, 2차와 3차 크리프가 대부분을 차지하였고, 최소 크리프 변형율은 Cu 함량이 0.75 wt %에서 최소이었고, 응력 지수는 약 4이었으며, 파단 시간 또한 0.75 wt% Cu에서 가장 길었다. 크리프 기구는 격자 확산에 의한 전위의 상승과 전위 활주에 의한 고온 크리프임을 앞 수 있었으며, Cu의 첨가는 1 wt% 가지 연성에 큰 영향을 주지 않았으나, 1.5 wt% 첨가했을 경우 연성은 크게 감소하였다.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.181-183
• /
• 2006

This paper studies the mechanical behaviors of Sn-3.5Ag solder joint against substrate(such as Au/Ni/Cu, Au/cu, Ni/Cu and Cu pad) after induction heating, a new soldering method. It was found that the solder bump formation depends on the time and current of the induction heating system. Also the heating value of the solder bump were found to vary with respect to the thermal conductivity of the pads on the substrate. In case of Au/Ni/Cu pad and Au/Cu pad, solder bump's shear strength were high for the heating time of $1.5{\sim}2sec$. For Ni/Cu pad, solder bump's shear strength were found to increase with time increment.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.333-337
• /
• 2008

This study investigates crack propagation behavior of Sn-3.0Ag-0.5Cu solder under pull-push loading conditions. Fatigue Crack Growth (FCG) tests were conducted on Center Cracked Plate (CCP) specimens in fast-fast (pp) strain waveform. The fast-slow (pc), slow-fast (cp) and slow-slow (cc) strain waveforms were also used to study the effect of strain rates. The crack propagation rates for the four strain waveforms were correlated with J-integral range and a scatter band of factor 4 was found. The crack growth rates for the pc waveform was highest, followed by cp, cc and then pp waveforms.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.284-284
• /
• 2015

반도체 Ball Grid Array(BGA)에 사용되던 종래의 Solder Ball은 Sn96.3 Ag3.0 Cu0.7의 용융솔더를 이용하여 제작하고 있다. 이는 SMT Reflow공정에서 BGA Ball의 퍼짐현상으로 인해 원래의 Ball Height에 영향을 미쳐 접합불량의 원인이 되고 있다. 이러한 문제를 해결하기 위해 Copper Core Ball위에 SnAgCu 삼원합금도금공정을 이용해 문제점을 해결하고자 했으며, 본 실험을 통해 구현한 CCSB를 이용해 SMT Reflow를 진행한 결과 종래의 BGA Ball보다 우수한 효과를 확인할 수 있었다.

• Proceedings of the Korean Reliability Society Conference
• /
• 2000.04a
• /
• pp.97-103
• /
• 2000

전자 산업의 발달에 따라 전자 패키지에서 소자의 소형화 및 고집적화가 가속화되고 그로 인해 interconnection 부분의 신뢰성 평가의 중요성이 나날이 증가되고 있다. 특히 이러한 interconnection 부분 중 솔더 접합부는 사용중 솔더와 UBM(Under Bump Metallurgy) 층 사이에 금속간화합물이 생성되어 접합 강도가 저하되는 것이 큰 문제로 지적되고 있다. 본 연구에서는 공정 Sn-Ag 솔더 접합부에 대해 열시효 시간에 따라 접합 강도를 측정하고 파괴 기구 및 파괴 경로의 분석을 통해 접합 강도 변화와의 연관성을 도출하고자 하였다. 그 결과 열시효 초기에는 미세 조직의 조대화 및 불균일 조대 성장이 가속화되면서 응력 및 변형 집중으로 인해 솔더 내부에서 연성 파괴가 일어나 급격한 접합 강도의 저하가 발생하였으나 금속간 화합물이 생성, 성장함에 따라 금속간 화합물 내부에서의 취성 파괴가 나타나면서 접합 강도 저하가 포화되는 경향을 보였다.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.1
• /
• pp.47-52
• /
• 2002

Intermetallic compound on the soldered interface plays important role on the bondability and mechanical properties of soldered joint. The formation of intermetallic compounds are influenced by many factors such as temperature, holding time, base metals and so on. On this study the effect of number of reflow times on the intermetallic growth was investigated. For the experimental materials, Sn-3.5Ag-0.7Cu solder ball of 0.3mm diameter and RMA-type flux were used. Thickness of intermetallic compound of solder ball by 2nd reflow showed nearly 60% higher than that of 1st reflow, and shear strength showed 10% higher value. Thickness and shear strength according to the position of interface such as upper side or lower side between two substrates were also investigated.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.11a
• /
• pp.33-37
• /
• 2002

본 연구에서는 전해도금법을 이용하여 플립칩용 Ni, Ni-Cu 합금 UBM (Under Bump Metallurgy) 및 Sn-Ag 무연 솔더 범프를 형성하였다. 솔더 범프의 전해도금시 고속도금 방법으로 균일한 범프 높이를 갖도록 하는 도금 조건 및 도금 기판의 역할로서의 UBM의 영향을 조사하였다. Cu/Ni-Cu 합금/Cu UBM을 적용한 경우 음극시편의 전극 접점수를 증가시켰을 때 비교적 균일한 솔더 범프를 형성시킬 수 있었던 반면, Ni UBM의 경우는 접점수를 증가시켜도 다소 불균일한 솔더 범프를 형성하였다. 리플로 시간을 변화하여 범프 전단 강도 및 파단 특성을 조사하였는데 Ni UBM의 경우 Cu/Ni-Cu 합금/Cu UBM에 비해 전단강도가 다소 낮은 값을 가졌고 금속막이 웨이퍼에서 분리되는 파괴 거동이 관찰되었다.

• Journal of the Korean institute of surface engineering
• /
• v.26 no.5
• /
• pp.245-254
• /
• 1993

The effects of pulse current electrolysis conditions on the composition and the microstructure of Ag-Sn alloy were studied by using a pyrophosphate bath. Both cathode current efficiency and throwing power of alloy deposits formed under pulse plating conditions, decreased with increasing mean current density, and lower than those under D.C. electrolysis condition. Tin content of Ag-Sn alloy decreased noticebly with in-creasing the mean current density, while it increased with the increase of On-time from 1 to 10 ms. The pre-ferred orientation of Ag-Sn alloy changed with increasing cathode overpotential in the sequence of (100)longrightarrow(100)+(111)longrightarrow(111) at $20^{\circ}C$ and (110)longrightarrow(111)longrightarrow(111)+(100) at $30^{\circ}C$. The effective crystal grain size of the alloy was decreased by decreasing temperature from $30^{\circ}C$ to $20^{\circ}C$ and the surface structure of them was related to the preferred orientation.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.2
• /
• pp.47-53
• /
• 2000

The fluxless wetting properties of TSM-coated glass substrate were evaluated by the wetting balance method. We could estimate the wettability of the TSM with new parameters obtained from the wetting balance test for one side-coated specimen. It was more effective in wetting to use Cu as a wetting layer and Au as a protection layer than to use Au itself as a wetting layer. The SnSb solder showed better wettability than SnAg, SnBi, and SnIn solders. The contact angle of the one side-coated glass substrate to the Pb-free solders could be calculated from the farce balance equation by measuring the static force and the tilt angle.

• Korean Journal of Materials Research
• /
• v.9 no.10
• /
• pp.1018-1024
• /
• 1999

The effects of operating temperature and stress on degradation of components in high temperature steam generator were investigated. Several 2.25CrlMo tubes which had operated over 20 years and an unused 9CrlMoVNb tube were tested. For the former samples, the amount of $\textrm{M}_{6}\textrm{C}$ carbide and its size are increased with the aging or operating time. The precipitation behavior of carbides ($\textrm{M}_{2}\textrm{O}$, $\textrm{M}_{6}\textrm{C}$) is changed with the operating temperature of the tubes. However, unused 9CrlMoVNb samples show a different carbide precipitation process due to high chromium, vanadium, and niobium contents. The amount of Cr-rich $\textrm{M}_{23}\textrm{C}_{6}$ carbide is significantly increased with aging time, but that of $\textrm{M}_{6}\textrm{C}$ type carbide is rarely changed with aging time at elevated temperatures.