• Journal of the Korean Chemical Society
• /
• v.15 no.2
• /
• pp.49-54
• /
• 1971

It is shown that the impurities of Cu(II), Pb(II), Zn(II) and Ag(I) in Bismuth metal and the components of Pb(II), Zn(II) and Sn(IV) in Bismuth alloy are separated into their components from each other by elutions through $3.14cm^2{\times}10cm$ cation exchange resin, $Dowex\;50w\;{\times}\;8$ (100~200 mesh), column with the mixed solutions of HAc and NaAc as the eluents. The elution curve of Fe(III) has a long tailing and is not separated quantitatively from Bi(III). The eluents used for this separation are as follows; 1M HAc + 0.1M NaAc (pH 3.36) for Fe(III) and Bi (III). 0.3M HAc + 0.3M NaAc (pH 4.70) for Cu(II), Pb(II) and Zn(II). 0.5M HAc + 0.5M NaAc (pH4.70) for Ag(I) and Sn(IV). The analysis of cations eluted are carried out by spectrophotometry and EDTA titrimetry. Their recoveries are more than 99%.

• 보존과학연구
• /
• s.10
• /
• pp.1-40
• /
• 1989

Between 1976 and 1984 approximately 26.7 tons of Chinese coins were recovered from a shipwreck which was found at the seabed of the Shin an area in the south-western coast of the Korean peninsula. Elements, Cu, Pb, Sn, Fe, Sb, As, Zn, Ag, Ni, Co and Mn, of 54 pieces of the coins were determined by Inductively Coupled Plasma Atomic Emission Spectroscopy(ICP-AIS). The result shows that Ch, Pb, and Sn were found to be major elements roughly the coins with the ratio of 7 : 2 : 1, respectively. Trace elements were classified into 3 levels according to the avarage concentration : Fe,As and Sb(0.1-0.5%), Ag, Mi, Co and Zn(100-1000ppm) and Mn(10ppm). Some systematic tendencies are observed in the composition change with a function of their minting ages .The Wuzhu coins(오수전) from the Eastern Han dynasty(A.D.25-219 )are much more abundant in Cu than the coins of Tang dynasty(A.D.618-907) and later periods. Major element compositions of the Kai -tong Vuan-Bao(개통원보) coins from the Tang dynasty, were remarkably variable. In general, however, the Tang dynasty coins were much more abundant in Cu than the Song dynasty(A.S.S60-1279) coins. The amount of major elements Cu and Sn decreases while that of Pb in creasesby passage of age from the Bei Song dynasty(A.D.960-1127) to later Nam Song dynasty (A.D.1127-1279 ). It means that the quality of coins mere degraded. The amounts of trace elemends(Fe, As, Co, Hn) increases with the above age. High amounts of trace elements are supposed to be a reflection of immaturity of minting techniques or use of impurity-rich raw materials. The Jin dynasty(A.D.1125-1234) coins are found to be rich in Sn and thus contain Pb as the third component. It is quite different from the coins of the Song dynasty. The Zhi-dai Tong-Bao(지대통보) coins of the Yuan dynasty from A.0.1310 are much more abundant in Cu and Sn than those of the Nam Song dynasty .

• Journal of the Korean institute of surface engineering
• /
• v.36 no.5
• /
• pp.373-378
• /
• 2003

With increasing environmental concerns, application of lead-free solder and fluxless soldering process have been taken attention from the electronic packaging industry. Plasma treatment is one of the soldering methods for the fluxless soldering, and it can prevent environmental pollution cased by flux. On this study fluxless soldering process under $Ar-H_2$plasma using lead free solders such as Sn-3.5 wt%Ag, Sn-3.5 wt%Ag-0.7 wt%Cu and Sn-37%Pb for a reference was investigated. As the plasma reflow has higher soldering temperature than normal air reflow, the effects of UBM(Under Bump Metallization) thickness on the interfacial reaction and bonding strength can be critical. Experimental results showed in case of the thin UBM, Au(20 nm)/Cu(0.3 $\mu\textrm{m}$)/Ni(0.4 $\mu\textrm{m}$)/Al(0.4 $\mu\textrm{m}$), shear strength of the soldered joint was relatively low as 19-27㎫, and it's caused by the crack observed along the bonded interface. The crack was believed to be produced by the exhaustion of the thin UBM-layer due to the excessive reaction with solder under plasma. However, in case of thick UBM, Au(20 nm)/Cu(4 $\mu\textrm{m}$)/Ni(4 $\mu\textrm{m}$)/Al(0.4 $\mu\textrm{m}$), the bonded interface was sound without any crack and shear strength gives 32∼42㎫. Thus, by increasing UBM thickness in this study the shear strength can be improved to 50∼70%. Fluxed reflow soldering under hot air was also carried out for a reference, and the shear strength was 48∼52㎫. Consequently the fluxless soldering with plasma showed around 65∼80% as those of fluxed air reflow, and the possibility of the $Ar-H_2$ plasma reflow was evaluated.

• Proceedings of the KIEE Conference
• /
• 2008.10a
• /
• pp.169-170
• /
• 2008

In this study, low temperature sintering property of the $0.6TiTe_3O_8-0.4MgTiO_3$ ceramics with sintering adds were investigated for LTCC application which enable to cofiring with Ag electrode. $TiTe_3O_8$ mixed with $MgTiO_3$ to improve the temperature property. In the X-ray diffraction patterns, the columbite structure of $TiTe_3O_8$ phase and ilmenite structure of $MgTiO_3$ phase were coexisted in all specimens. In the case of SnO addition, the bulk density and dielectric constant were increased but quality factor was decreased with amount of SnO additions. The TCRF of the $0.6TiTe_3O_8-0.4MgTiO_3$+xwt%SnO ceramics were shifted to negative direction. The dielectric constant, quality factor and TCRF of the $0.6TiTe_3O_8-0.4MgTiO_3$ ceramics with 2.5wt% addition of SnO sintered at $830^{\circ}C$ for 1hr were 29.86, 35,800 GHz, -0.58 ppm/$^{\circ}C$, respectively.

• The Korean Journal of Mycology
• /
• v.14 no.3
• /
• pp.209-214
• /
• 1986

In order to study the trehalase (EC 3. 2. 1. 28) from mushroom, Agaricus bisporus Lange Sing., the crude trehalase preparation was separated by fractionation of mushroom extracts with ammonium sulfate between 0.4 and 1.0 saturation, and its properties were examined. Mushroom trehalase showed optimum pH 6.0, and optimum temperature $40^{\circ}C$. The enzyme was stable at pH range between 5.0 and 7.0, and at temperature below $50^{\circ}C$. The activities of crude trehalase had proportional relations with enzyme concentrations below 490.2 mg % of protein and with substrate concentration below $2.6{\times}10^{-3}M$, showing a Km value of 0.760 mM. The enzyme was inhibited by some metal ions such as $Sn^{2+}$, $Ca^{2+}$, $Hg^{2+}$, $Cd^{2+}$, $Cu^{2+}$, $Mn^{2+}$, $Zn^{2+}$, $Al^{3+}$, and $Fe^{3+}$, while $Ag^{+}$, $Ba^{2+}$, and $Mg^{2+}$ demonstrated remarkable increasing effects on the enzyme activity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.24-24
• /
• 2009

투명전극 (TCO Transparent Conductive Oxide)은 Solar cell, Touch panel, Sensor 등 많은 분야에 이용되어지고 있다. ZnO 그리고 $SnO_2$는 ITO룰 대체하기 위하여 오래전부터 연구가 되어지고 있다. 하지만 ZnO가 가지고 있는 많은 장점에도 불구하고 ITO를 대체하기 위한 전기적 특성이 충분하지 않다. 따라서 ZnO에 Al를 도핑하는 등 다양한 연구가 진행되어왔다. 본 실험은 우수한 광학특성 및 전기적 (10-5) 특성을 확보하기 위하여 AZO/Ag/AZO 다층박막구조 형성하였다. 또한 염료감응 태양전지에 적용하기 위하여 다층박막구조를 이용한 안정성 테스트를 진행하였다.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.3
• /
• pp.63-71
• /
• 2022

In this study, the interfacial reaction and drop impact reliability of Sn-Ag-Cu (SAC) solder and electroless nickel autocatalytic gold (ENAG) were studied. In addition, the solder joint properties with the ENAG surface finish was compared with electroless nickel immersion gold (ENIG) and electroless nickel electroless palladium immersion gold (ENEPIG). The IMC thickness of SAC/ENAG and SAC/ENEPIG were 1.15 and 1.12 ㎛, respectively, which were similar each other. The IMC thickness of the SAC/ENIG was 2.99 ㎛, which was about two times higher than that of SAC/ENAG. Moreover, it was found that the IMC thickness of the solder joint was affected by the metal turnover (MTO) condition of the electroless Ni(P) plating solution, and it was found that the IMC thickness increased when the MTO increased from 0 to 3. The shear strength of SAC/ENEPIG was the highest, followed by SAC/ENAG and SAC/ENIG. It was found that when the MTO increased, the shear strength was lowered. In terms of brittle fracture, SAC/ENEPIG was the lowest among the three joints, followed by SAC/ENAG and SAC/ENIG. Likewise, it was found that as MTO increased, brittle fracture increased. In the drop impact test, it was confirmed that the 0 MTO condition had a higher average number of failures than the 3 MTO condition, and the average number of failures was also higher in the order of SAC/ENEIG, SAC/ENAG, and SAC/ENIG. As a result of observing the fracture surface after the drop impact, it was found that the fracture was between the IMC and the Ni(P) layer.

• Restorative Dentistry and Endodontics
• /
• v.19 no.1
• /
• pp.1-26
• /
• 1994

The purpose of this study was to investigate the dissolution components during corrosion of amalgams and to identify surface corrosion products in the modified Fusayama artificial saliva. Four type of amalgam alloys were used: low copper lathe cut amalgam alloy (Cavex 68), low copper spherical amalgam alloy (Caulk Spherical Alloy), high copper admixed amalgam alloy (Dispersalloy) and high copper single composition amalgam alloy (Tytin). Each amalgam alloy and Hg were triturated according to the manufacturer's direction by means of mechanical amalgamator (Capmaster, S.S.White), and then the triturated mass was inserted into the cylindrical metal mold which was 10mm in diameter and 2.0mm in height and condensed with compression of 150kg/$cm^2$ using oil pressor. The specimens were removed from the mold and stored at room temperature for 7 days and cleansed with distiled water for 30 minutes in an ultrasonic cleaner. The specimens were immersed in the modified Fusayama artificial saliva for the periods of 1 month, 3 months and 6 months. The amounts of Hg, Cu, Sn and Zn dissolved from each amalgam specimen immersed in the artificial saliva for the periods of 1 month, 3 months and 6 months were measured using Inductivity Coupled Plasma Atomic Emission Spectrometry (ICPQ-1000, Shimadzu, Japan) and amount of Ag dissolved from amalgam specimen was measured using Atomic Absorption Spectrophotometry (Atomic Absorption/Flame emission spectrophotometer M-670, Shimadzu, Japan). A surface corrosion products of specimens were analysed using Electron Spectroscopy Chemical Analyser (ESCA PHI-558, PERKIN ELMER, U.S.A.). The secondary image and back scattered image of corroded surface of specimens was observed under the SEM, and the corroded surface of specimens was analysed with the EDX. The following results were obtained. 1. The dissolution amount of Cu was the most in high copper admixed amalgam(Dispersalloy) and the least in high copper single composition amalgam(Tytin). 2. Sn and Zn were dissolved during all the experiment periods, and dissolution amounts were decreased as the time elapsed. 3. Initial surface corrosion products were ZnO and SnO. 4. Corrosion of ${\gamma}$ and ${\gamma}_2$ phase in low copper amalgams was observed and Ag-Cu eutectic alloy phase was corroded in low copper spherical amalgam(Caulk Sperical Alloy). 5. Corrosion of ${\gamma}$ and $\eta$' phase in high copper amalgams was observed and Ag-Cu eutectic alloy phase was corroded in high copper admixed amalgam(Dispersalloy). 6. Sn-Cl was produced in the subsurface of low copper amalgams and high copper admixed amalgam.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.4 s.37
• /
• pp.331-338
• /
• 2005

The rapid advances in high power light sources and arrays as encountered in incandescent lamps have induced dramatic increases in die heat flux and power consumption at all levels of high power LED packaging. The lifetime of such devices and device arrays is determined by their temperature and thermal transients controlled by the powering and cooling, because they are usually operated under rough environmental conditions. The reliability of packaged electronics strongly depends on the die attach quality, because any void or a small delamination may cause instant temperature increase in the die, leading sooner or later to failure in the operation. Die attach materials have a key role in the thermal management of high power LED packages by providing the low thermal resistance between the heat generating LED chips and the heat dissipating heat slug. In this paper, thermal transient characteristics of die attach in high power LED package have been studied based on the thermal transient analysis using the evaluation of the structure function of the heat flow path. With high power LED packages fabricated by die attach materials such as Ag paste, solder paste and Au/Sn eutectic bonding, we have demonstrated characteristics such as cross-section analysis, shear test and visual inspection after shear test of die attach and how to detect die attach failures and to measure thermal resistance values of die attach in high power LED package. From the structure function oi the thermal transient characteristics, we could know the result that die attach quality of Au/Sn eutectic bonding presented the thermal resistance of about 3.5K/W. It was much better than those of Ag paste and solder paste presented the thermal resistance of about 11.5${\~}$14.2K/W and 4.4${\~}$4.6K/W, respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.2
• /
• pp.47-54
• /
• 2008

In this paper, we studied how and why did abnormal IMC growth at component affect on board level mechanical reliability. First, interfacial reactions between Sn2.5Ag0.5Cu solder and electrolytic Ni/Au UBM of component side were investigated with reflow times and thermal aging time. Also, to compare mechanical reliability of component level, shear energy was evaluated using the ball shear test conducted with variation of shear tip speed. Finally, to evaluate mechanical reliability of board level, we surface-mounted component fabricated with each condition on PCB side. After conducting of 3 point bending test and impact test, we confirmed solder joint crack mode using cross-sectioning and dye & pry penetration method.