• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.2
• /
• pp.111-118
• /
• 2004

A number of researchers have attempted to measure the reverberation time of a passenger car, ut the reverberation time of passenger car is too short to measure with the traditional band pass filter. And if the reverberation time is very short, the product of the reverberation time (T) and the bandwidth (B) of the traditional band pass fitter becomes small. The low limit of BT product required for the measurement of reverberation time with the traditional band pass filter is 16. In order to overcome this problem, the wavelet filter bank was developed. In this study, this new wavelet filter was employed to measure the reverberation times of five different classes of passenger cars. The low limit of BT product required for the measurement of reverberation time with the wavelet filter is 4. The reverberation times of five passenger cars were measured successfully with the new wavelet filter bank. The reverberation times measured in most passenger cars was found to be around 0.04. Compared with general acoustic rooms like concert halls, this is a very short reverberation time

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_2
• /
• pp.1071-1081
• /
• 2022

As the demand for high-rise buildings increases, the demand for high-speed elevators is also increasing. In order to make a high-speed elevator, a method is needed to reduce the weight of the elevator's components, which is a constraint on the increase in speed. As a measure to reduce the weight, it is possible to remove the traveling cable for power and signal supply. Since the weight of the traveling cable varies depending on the position of the carriage, it is difficult to compensate the weight using the counter weight. The power supply is a structure in which a brush-rail type power input terminal is installed in the elevator hoistway to receive power in a contact-type manner while the carriage is moving. If a small-capacity ESS is installed in a passenger car, power can be supplied uninterruptedly inside the passenger car. A small-capacity ESS charging system to be applied to such an elevator system is required to perform several functions. First, the passenger Car must be able to charge as much as possible even during high-speed operation. A control algorithm with high responsiveness is required because charging starts and ends repeatedly by the partially installed input power stage. In addition, if the input-side line impedance is large due to the structure of the system and the response characteristic is increased, the stability of the system may be lowered. Accordingly, in this paper, we propose a control algorithm that has a stable steady-state output while having a fast response in a transient state. To verify the proposed control algorithm, simulation was conducted using PSIM, and the performance of the controller was verified by manufacturing a prototype buck conveter charger.

• Journal of Korean Society of Transportation
• /
• v.28 no.6
• /
• pp.65-74
• /
• 2010

This study aims at developing a method for estimating passenger car equivalency (PCE) values for various vehicle types that could be considered in estimating capacity and delay at intersections without traffic signals, especially at modern small 3-leg roundabouts. Unlike signalized intersections, the PCE value has not yet been treated explicitly in traffic operations involving unsignalized intersections. Both empirical and theoretical approaches for determining the PCE values at modern small 3-leg roundabouts were evaluated. As a result, the PCEs derived in this study were highly correlated with those of field measurements.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.2
• /
• pp.91-99
• /
• 2013

Car cross beam made by aluminium for new car is designed for the substitution of steel and it can be verified the performance by computer simulations. The parts of car cross beam are designed to replace steel parts according to their manufacturing processes. At the first stage, the weight of the aluminium car cross beam can be reduced to 75% by comparing with that of steel car cross beam. But NVH performance of the aluminium car cross beam becomes slightly insufficient as compared with that of steel car cross beam. Taguchi method is adopted to optimize the design variables affecting NVH characteristics of car cross beam. New car cross beam is designed at the second stage by using these analysis results. Weight reduction can be obtained to 31.7% by design modification and material change of car cross beam in comparison with the original steel one. NVH characteristics of aluminium car cross beam become on an equal level with the steel car cross beam. By side impact analysis results, new car cross beam has higher performance as compared with the steel car cross beam.

• Journal of the korean Society of Automotive Engineers
• /
• v.5 no.2
• /
• pp.56-63
• /
• 1983

The aerodynamic characteristics of the most popular car (PONY 2) produced in Korea have been experimentally investigated by Seoul National University's wind tunnel. The model (PONY 2) chosen for the wind tunnel was a 1/5 scale of the original car without simulated underbody, cooling air flow and accessories. The measured aerodynamic drag coefficient corrected by JARI formula is 0.45 which is very close to those of small foreign cars. To see the effect of the different configurations on the aerodynamic drag, the modifications have been made by changing the hood slope and backlight slope, and putting the add-on-aerodynamic devices on the orignal shape. The rear spoiler was found the most effective one to reduce the aerodynamic drag. It may be concluded that the considerable aerodynamic drag reduction can be achieved by changing the slopes and A-O-A devices at the proper places of the car.

• International Journal of Safety
• /
• v.7 no.1
• /
• pp.5-9
• /
• 2008

For the purpose of controlling the coupling between the car body panels and passenger compartment, experimental investigation of an acoustic cavity with an air gap is carried out to reveal how the air gap influences the acoustic modal characteristics of the cavity. The acoustic modal characteristics of the cavity is closely related with the booming noise. The experimental results show that a very small air gap can change the acoustic modal characteristics of the cavity and, as a result, the air gap can be an important factor in controlling the booming noise for comfortable and safe passenger compartment.

• International Journal of Automotive Technology
• /
• v.7 no.2
• /
• pp.195-199
• /
• 2006

According to the United States FMVSS 208, every passenger car on the market after September of 2006 must install a safety system, which can deploy the airbag with different intensity or suppression based on the passenger type, to reduce infant and child injuries from airbag deployments. The Weight Classification System, which has been developed by Hyundai Autonet, is a system that classifies the person occupying the passenger seat. To overcome sensing problems due to the weight sensors small voltage, the Distributed Systems Interface is adopted.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.564-569
• /
• 2013

An accurate railway environmental noise prediction model is required to make the proper solution of the railway noise problems. In this paper, an engineering model for predicting the noise of conventional passenger cars is presented considering the acoustic source strength in octave-band frequencies and the propagation over grounds with varying surface properties. Since the formation of a train can be variable, the source strength of each locomotive and passenger car was estimated by measuring the pass-by noise and analysing the wheel-rail rolling noise. Some validation cases show on the average small differences between the predictions of the present model and the measurement results.

• Journal of the korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.54-61
• /
• 1984

Numerical calculation of the flow field past a passenger car was carried out by using a panel method with a small computer of 5Mbyte memory size. The shape of car body was simplified and reconstructed by 2180 panels on which a constant strength sink (or source) was distributed. The separation of flow from the surface and the wake flow were not considered in the calculation because of the computer memory limitation. All of the results of calculation were presented by using a 3-dimensional computer graphics. In spite of small memory size of computer, generally good agreements were obtained, except the separated region, from the comparison of pressure distribution between numerical analysis and wind tunnel experiment with 1/5 scaled model.

• Journal of Auto-vehicle Safety Association
• /
• v.10 no.3
• /
• pp.32-37
• /
• 2018

Recently, the driver can be assisted by the advanced active safety devices such as ADAS from road traffic risks. With this system, driver and passenger may freed from can driving tasks or kept eyes on forward direction while on the road. Help from adoptive cruise control, auto parking and newly develped automated driving vehicles technologies, the driver positions will vary significantly from the current standard driver position during the travel time. On this hypothesis, the objective of this study is analyze the behavior and injuries of drivers in the event of frontal impact under these abnormal driver position. Based on the KNCAP frontal impact testing method, this simulation matrix was set-up with dummies of 5 th tile female Hybrid III dummy and 50 th tile male Hybrid III dummy. The small sedan type passenger car was modeled in this simulation. The series of simulation was performed to compare the injuries and behaviour of each dummy, varying the seating status and seat position of each dummy.