• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1807-1812
• /
• 2004

Sinusoidal wavy channel is one of the most commonly used devices in the industry for achieving mixing and heat transfer. Here we report on results obtained from the DNS of flow inside the wavy channel performed using the finite volume technique. As a primary stage to obtain the optimal design for heat transfer and mixing, this study observed the basic flow structures in a wavy channel. The mass flow rate is kept constant with friction Reynolds number of $Re_{\tau}$ = 140 . Time- and space-averaged and instantaneous flow fields are illustrated to observe the flow structures. Although the direct comparison of results between turbulent wavy and flat channel is somehow difficult due to the different flow phenomena derived from different configuration, here the mean streamwise velocity and RMS of velocities at same $Re_{\tau}$ of two different channels are compared. The basic difference between wavy and flat channel flow is the existence of small scale wall vortices along the walls in a wavy channel. These vortices make flow more complex, which will accompany the increase of heat transfer, pressure drop and drag.

• Structural Engineering and Mechanics
• /
• v.56 no.2
• /
• pp.241-256
• /
• 2015

Channel girder bridges that consist of a deck slab and two side beams are good choices for railway bridges and urban rail transit bridges when the vertical clearance beneath the bridge is restricted. In this study, the behavior of simply supported channel girder bridges was theoretical studied based on the theory of elasticity. The accuracy of the theoretical solutions was verified by the finite element analysis. The global bending of the channel girder and the local bending of the deck slab are two contributors to the deformations and stresses of the channel girder. Because of the shear lag effect, the maximum deflection due to the global bending could be amplified by 1.0 to 1.2 times, and the effective width of the deck slab for determining the global bending stresses can be as small as 0.7 of the actual width depending on the width-to-span ratio of the channel girder. The maximum deflection and transversal stress due to the local bending are obtained at the girder ends. For the channel girders with open section side beams, the side beam twist has a negligible effect on the deflections and stresses of the channel girder. Simplified equations were also developed for calculating the maximum deformations and stresses.

• Water Engineering Research
• /
• v.2 no.4
• /
• pp.219-229
• /
• 2001

Synthetic unit hydrograph equations for rainfall run-off characteristics analysis and estimation of design flood have long and quite frequently been presented, the Snyder and SCS synthetic unit hydrograph. The major inputs to the Snyder and SCS synthetic unit hydrograph are lag time and peak coefficient. In this study, the methods for estimating lag time and peak coefficient for small watersheds proposed by Zhao and McEnroe(1999) were applied to the Kum river basin in Korea. We investigated lag times of relatively small watersheds in the Kum river basin in Korea. For this investigation the recent rainfall and stream flow data for 10 relatively small watersheds with drainage areas ranging from 134 to 902 square kilometers were gathered and used. 250 flood flow events were identified along the way, and the lag time for the flood events was determined by using the rainfall and stream flow data. Lag time is closely related with the basin characteristics of a given drainage area such as channel length, channel slope, and drainage area. A regression analysis was conducted to relate lag time to the watershed characteristics. The resulting regression model is as shown below: ※ see full text (equations) In the model, Tlag is the lag time in hours, Lc is the length of the main river in kilometers and Se is the equivalent channel slope of the main channel. The coefficient of determinations (r$^2$)expressed in the regression equation is 0.846. The peak coefficient is not correlated significantly with any of the watershed characteristics. We recommend a peak coefficient of 0.60 as input to the Snyder unit-hydrograph model for the ungauged Kum river watersheds

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.9
• /
• pp.1209-1218
• /
• 2001

The present paper proposes a new correlation for the flow boiling heat transfer coefficients in the low flow rate condition (Re(sub)LF$\leq$200) within horizontal rectangular channels with small gaps (heights). The gap between the upper and the lower plates of each channel ranges from 0.4 to 2mm while the channel width being fixed to 20mm. Refrigerant 113 was used as the test fluid. The mass flux ranges from 50 to 200kg/㎡s and the channel walls were uniformly heated with the heat flux range of 3-15kW/㎡. The quality range covers from 0.19 to 0.76 and the flow pattern is considered to be annular. The measured heat transfer coefficients increase with the mass flux and the local quality; however the effect of the heat flux appears to be minor. At the low mass flux condition, which is more likely with the smaller gap size, the heat transfer is primarily controlled by the liquid film thickness. The proposed F factor for the heat transfer coefficient in the range of Re(sub)LF$\leq$200 well represents the experimental data within the deviation of $\pm$20%. The Kandlikars flow boiling correlation covers the higher flow-rate range(Re(sub)LF>200) within the deviation of $\pm$20%.

• Journal of information and communication convergence engineering
• /
• v.9 no.6
• /
• pp.733-737
• /
• 2011

This paper has studied subthreshold characteristics for double gate(DG) MOSFET using Gaussian function in solving Poisson's equation. Typical two dimensional analytical transport models have been presented for symmetrical Double Gate MOSFETs (DGMOSFETs). Subthreshold swing and threshold voltage are very important factors for digital devices because of determination of ON and OFF. In general, subthreshold swings have to be under 100mV/dec, and threshold voltage roll-off small in short channel devices. These models are used to obtain the change of subthreshold swings and threshold voltage for DGMOSFET according to channel doping profiles. Also subthreshold swings and threshold voltages have been analyzed for device parameters such as channel length, channel thickness and channel doping profiles.

• BMB Reports
• /
• v.44 no.10
• /
• pp.635-646
• /
• 2011

Due to its high external and low internal concentration the $Ca^{2+}$ ion is used ubiquitously as an intracellular signaling molecule, and a great many $Ca^{2+}$-sensing proteins have evolved to receive and propagate $Ca^{2+}$ signals. Among them are ion channel proteins, whose $Ca^{2+}$ sensitivity allows internal $Ca^{2+}$ to influence the electrical activity of cell membranes and to feedback-inhibit further $Ca^{2+}$ entry into the cytoplasm. In this review I will describe what is understood about the $Ca^{2+}$ sensing mechanisms of the three best studied classes of $Ca^{2+}$-sensitive ion channels: Large-conductance $Ca^{2+}$-activated $K^+$ channels, small-conductance $Ca^{2+}$-activated $K^+$ channels, and voltage-gated $Ca^{2+}$ channels. Great strides in mechanistic understanding have be made for each of these channel types in just the past few years.

• Journal of computational fluids engineering
• /
• v.16 no.1
• /
• pp.90-95
• /
• 2011

The Navier-Stokes equations are solved to study the flow characteristics of a micro viscous pump. The viscous micropump is consisted of a stationary disk with a spiral shaped channel and a rotating disk. A simple geometrical model for the tip clearance is proposed and validated by comparing computed flow rate with corresponding experimental data. Present numerical solutions show satisfactory agreement with the corresponding experimental data. The tip clearance effect is found to become significant as the rotational speed increases. As the pressure load increases, a reversed flow region is seen to form near the stationary disk. The height of the channel is shown to be optimized in terms of the flow rate for a given rotational speed and pressure load. The optimal height of the channel becomes small as the rotational speed decreases or the pressure load increases. The flow rate of the pump is found to be in proportion to the width of channel.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.1 no.1
• /
• pp.47-54
• /
• 1997

New algorithms for frequency channel assignment in small cellular mobile radio system are proposed. The algorithms are for a channel assignment method which control the transmitter power level based on the distance between the cell site and the mobile unit. These algorithms are such that any channel can be used by any cell site and mobile unit, as long as a required threshold level of carrier to interference ratio is maintained. As the cochannel reuse distance decreases, the proposed algorithms have given an increase in capacity in comparison to a fixed channel assignment.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.9
• /
• pp.863-871
• /
• 2004

In this paper, we propose a subspace channel estimation technique for DS/CDMA DMB down link system, which can obtain reduction in numerical complexity by using of matched filtering outputs. The complexity reduction is considerable when the channel length is small and the system is moderately loaded. Previously proposed subspace-based blind channel estimation algorithm suffer from high numerical complexity for systems with large spreading gains. Although the proposed algerian suffers a slight performance loss, it becomes negligible for large observation length. Performance is evaluated through simulations and the derivation of the analytical MSE.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.5
• /
• pp.311-317
• /
• 2009

Due to extremely small device size and velocity scale, mixing in microchannel take place very slowly by way of molecular diffusion transport. Mixing enhancement becomes a central issue in microfluidics for biomedical and chemical applications. In this work, The optimization results and validation through experiment and fabrication. In this efficient micromixer design, it is essential to evaluate mixing efficiency with good precision. Mixing efficiency for Y-channel micromixer is measured by fluorescence intensity using LIF(Laser Induced Fluorescence) Confocal Microscope. The Y-channel micromixers are fabricated with polydimethylsiloxane(PDMS). Nile Blue A is injected into the micromixer as a fluorescence dye for measuring of fluorescence intensity by He/Ne laser. Throughout the experiments and computer simulation, accurate mixing efficiency evaluation process for a PDMS Y-channel micromixer is established.