• 한국해양공학회지
• /
• 제22권4호
• /
• pp.84-89
• /
• 2008

It is hard to find experimental data for a model test of small high-speed planning boats. It is difficult to verify the performance seen in a model test for a high-speed boat because the ship-model scale-ratio is very small and the flow velocity of the circulating water channel and the X-carriage speed of the towing tank are restricted. Therefore most hull-form designs for high-speed small boats depend on the sea-trial test result for similar boats or evaluation through numerical calculations. This study investigated the anti-rolling effect of the stern sub-body in a 50-knot doss planning boat. To carry out this work, new model test procedures were set up in the actual sea. Using this method, the anti-rolling effect of the stern sub-body was investigated. A stern sub-body attached to a planning boat was proved to be effective in reducing the roll and pitch angle.

• 한국항해항만학회지
• /
• 제34권8호
• /
• pp.623-628
• /
• 2010

현재 모형선을 이용한 선형성능 검증설비는 예인수조와 회류수조 두설비가 주로 이용된다. 이들 설비는 주로 저속 대형선박을 위해 기법들로 소형 고속어선 및 고속레저선박의 저항성능 평가를 수행하기에 전차의 속도와 유속이 목표속도에 미치지 못해 어려움이 존재한다. 따라서 고속 선박의 저항성능 평가를 위해 새로운 기법 정립 연구가 필요하다. 이에 고속선의 저항성능 시험을 위해 실제 해상에서 선박을 이용한 모형시험을 고안하고 측정시스템을 구성하였다. 시스템구성은 총 8개의 파트로 구성되어 있으며, 시스템 검증을 위해 C.W.C에서 저속선의 모형을 이용하여 시험을 수행하여 시스템 적용 가능성을 검증하였다. 또한 실제 해상에서 고속선 모형선을 이용하여 시험을 수행하였으며, 이 결과를 CFD해석 결과와 비교하여 실해상 모형시험 방법의 가능성을 확인 하였다.

• 해양환경안전학회지
• /
• 제21권6호
• /
• pp.784-789
• /
• 2015

본 연구는 소형 고속정의 운항한계를 검토하기 위하여 수행되었다. 일반적으로 내항성능의 검토는 선형의 결정 단계 전에 이루어지지만 본 연구는 선박의 건조가 완료된 후에 이루어졌다. 검토 결과, 종동요, 수직 및 수평가속도, 슬래밍의 운동성능은 특정한 조우각을 제외하고는 만족하였으나 갑판침수의 경우에는 해석을 수행한 모든 조건에서 만족하지 않았다. 이것은 대상선박의 크기가 소형이기 때문에 선박의 속도나 파도와의 조우각보다는 해상상태가 설정한 내항성능 기준의 만족 여부에 더 큰 영향을 미쳤기 때문으로 보인다.

• 대한조선학회논문집
• /
• 제49권2호
• /
• pp.182-188
• /
• 2012

The hull form design technique for high speed power boat based on the parametric design method is presented in this paper. While the design methods of conventional vessels that are currently in use have been well developed in various aspects from existing database. However, an easy and simple design program for high speed power boats needs to be provided for the relatively small boat builders who are in lack of experience and skilled manpower. This paper presents a parametric design technique which is aimed to provide an easier creation of a new model by inputting several parameters, such as angles and lengths, which correlate with hydrodynamics characteristic for high speed boats. The paper also introduces the prototype program developed to design power boat with parametric design technique.

• Journal of Ship and Ocean Technology
• /
• 제10권1호
• /
• pp.1-9
• /
• 2006

The resistance reduction by an air lubrication effect of a large air cavity covering the hull bottom surface and the similarity relations involved have been investigated with a series of towing tank tests of three geometrically similar models. The test results of geometrically similar models have indicated that a large air cavity was formed beneath the bottom having a backward-facing step by artificially supplying air is effective for resistance reduction. The areas of air cavity and the required flow rates of air are directly related to the effective wetted surface area. The traditional extrapolation methods seem to be applicable to the estimation of the resistance in the tested range if corrections are made to account the changes in the frictional resistance caused by the changes in the effective wetted surface area. To investigate the effectiveness of air lubrication in improving the resistance performance of a practical ship, a small test boat having a backward-facing step under its bottom has been manufactured and speed trials in a river have been performed. Air has been supplied artificially into the downstream region of the bottom step to form a large air cavity covering the bottom surface. The results have confirmed the practical applicability of air lubrication for the resistance reduction of a small high-speed boat.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.213-215
• /
• 2004

Water jet propulsion system has high efficiency on middle to high speed, and it provides better safety than conventional screw propeller because it has not projected propeller and rudder. So many leisure boat and high-speed ferries use this propulsion system. We developed water-jet propulsion unit for small planning boat, and launched that in the boat, after that we tested water-jet unit in the lake. As a result, we certify heat dissipation at the bearing housing and reverse duct's shape for neutral position are important at the design, and alignment water-jet unit and keel line are important at the launching, and ship's resistance performance and jet's propulsion performance also are needed to consideration.

• 수산해양기술연구
• /
• 제44권1호
• /
• pp.68-74
• /
• 2008

This study is concerned with the development of the basic planing hull form of small fishing boat in 25 knots high speed. A series of model test to determine the optimum performance hull form of actual fishing boat with 10 gross tonnage was carried out for 5 models made available planing hull form in the circulation water channel. Model test was performed with the resistance test to study the hydrodynamic characteristics of model ships and the sinkage and trim measurement to investigate the stability of model ships and also the wave pattern observation to analyze the effectiveness of model ships. As the result, the planing hull form of P-4 with deep V type bow can be derived as the best hull form with good performance especially in ship's resistance efficiency showing less residual resistance and sinkage and trim and the spray effect, etc..

• 한국항해항만학회지
• /
• 제42권3호
• /
• pp.177-186
• /
• 2018

보트의 초기설계단계에서 설계자는 주요치수 결정을 위해 많은 정보를 필요로 하며, 그러한 정보의 대부분은 해당 보트와 유사한 실적선 자료들을 많은 시간에 걸쳐 조사 및 분석함으로써 얻을 수 있다. 또한, 결정된 주요치수는 설계과정(기본/상세설계) 전반에 걸쳐 영향을 미치게 되고, 이는 결국 보트의 안정성과 성능으로 직결된다. 따라서 본 연구에서는 700여 척의 실적선 자료를 이용하여 보트 초기설계시스템(설계지원플랫폼)을 개발하고, 50피트급 고속보트를 대상으로 이를 활용하여 설계자가 초기설계단계에서도 주요치수를 편리하고 합리적으로 도출 및 결정할 수 있음을 확인하였다.

• 대한조선학회논문집
• /
• 제48권2호
• /
• pp.158-164
• /
• 2011

The study on the improvement of resistance performance is very important for coastal fishing boats in Korea, because the prices of fuel oil are gradually risen and the demand of high-speed fishing boats is increased lately. This study is concerned with the improvement of the resistance performance for Korean high-speed small coastal fishing boats. A semi-planing hull form of Korean small coastal fishing boat is selected in the role of initial hull. From the modification of the hull form parameters and the local characteristics of the hull form, the improvement of the resistance performance is achieved. The resistance performances of the initial and the modified hull forms are estimated by using a numerical simulation method. Also, ship model tests are carried out in ship model basin.

• 한국항해학회지
• /
• 제1권1호
• /
• pp.45-62
• /
• 1977

The advanced researches of the ship's motion in the seaway can predict the heaving, pitching and slamming of ship's motion. The researches as of today are that of displacement type such as a small typical fishing boat and U, UV and V bow ship forms under low speed. In recent day, the study of behaviours of high speed planning boat in the regular waves has been carried out by Bessho [5]. The calculation about behaviours of a high speed vessel in the longitudinal regular waves is calculated by Ordinary Strip Method in this paper. The data of the results were discussed and compared with Bessho's results. The conclusions deduced from this study are as follow, (1) The acceleration of motion calculated by the O.S.M. is similar with Bessho's data for the Fn 0.5 (2) The amplitudes of the behaviours of motions take peak at 1.0<λ/L<1.4.