• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.4
• /
• pp.894-900
• /
• 2004

There are many types of circularly polarized(CP) microstrip antenna elements, which are used as a good unit radiator. Since an advantage of CP antenna is no strict alignment requirements between Rx and Tx system, the printed antennas with circular polarization are very often used in numerous satellite and mobile radio systems. In order to realize the broad bandwidth of 3 dB axial ratio and impedance of CP microstrip antenna, complex feed structure and tri-plate patch element have been researched. This paper describes a design of wideband microstrip cross slot array antennas with circular polarization. The proposed antenna is composed of an open-ended microstrip feed line as a feeder and a cross slot as a radiator for circular polarization. To realize the wide bandwidth, tri-plate structure are considered and cross slot is electromagnetically coupled with feed line. Optimum parameters of 1-element cross slot antenna are analyzed and designed by method of moments. These parameters are also applied to may antennas design considered the mutual coupling between radiating elements. Right hand circular polarization(RHCP) and left hand circular polarization(LHCP) of the proposed antenna are easily controlled by asymmetrical cross slot structure and slot position. In 1-element and 15-element cross slot array antenna, the good axial ratio of 1 dB below and the broad bandwidth characteristics of antenna are obtained.

• Journal of electromagnetic engineering and science
• /
• v.11 no.2
• /
• pp.97-104
• /
• 2011

A planar slotted waveguide array antenna has been designed at 9.37 GHz for X-band radar applications. The antenna consists of multiple branchline waveguides with broadwall radiating shunt slots and a main waveguide to feed the branch waveguides through a series of inclined coupling slots. The antenna feed point is located at the center of the main waveguide. Element weights in the array have been calculated bysampling a continuous circular Taylor aperture distribution at the 25 dB sidelobe level in both the E and Hplanes. A commercially available electromagnetic (EM) simulation tool has been used to characterize the individual isolated slot and that data hassubsequently been used to design the planar array. The array is finally analyzed in a CST Microwave studio and the measured and simulated results have been found to be in good agreement.

• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.126-131
• /
• 2005

To increase the efficiency of an applicator during microwave hyperthermia therapy, first, the length from the antenna end to a slot is varied to get the optimal matching of the characteristic impedance at the frequency of 2.45 GHz. Using the electric and thermal constants of biological tissue, we compose a phantom to calculate temperature increment as well as the resonance characteristics and the SAR distributions. The proposed 3-slot sleeve antenna inserted in an applicator plays an effective role in increasing the therapy size in the view of heating performance as electromagnetic energy tends to concentrate on not feed point direction but treatment area. The SAR is then used in combination with a finite difference heat transfer equation to determine the temperature distribution. Also, in order to shorten treatment time and increase therapy size, a square-array structure is suggested and analyzed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.2
• /
• pp.257-260
• /
• 2014

In this paper, a high gain waveguide array antenna combining horn antenna on slot radiator was designed. And the fabricated antenna showed enough gain, improved efficiency and broadband characteristics for receiving satellite signals, compare to conventional microstrip antenna which has dielectric loss and radiation loss on transmission line. For easy fabrication, the waveguide structure was composed by 3-stages of radiator, signal coupler and transmission line. By experiment, the array waveguide antenna of 4 by 16 showed 28.3[dBi] gain and 2:1 of VSWR. And by combining horn antenna structure, the gain was increased 1[dB]. The received signal from Koreasat 6 by measurement showed 16[dBc] of C/N on BS(Broadcasting Satellite)-band and 14[dBc] of C/N on CS(Communication Satellite)-band.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.3 s.357
• /
• pp.105-110
• /
• 2007

We have built the millimeter-wave passive imaging system with a lens and mechanical scan antenna. The lens was designed based on optical theory in order to focus millimeter-wane. A full image was taken from image points scanned by Placing antenna at the representative focal plane selectively. An integrated antenna array device for low-loss and low-noise with the array of 4 by 1, where components such as antenna, balun, MMIC, and detector were assembled on a sin91e substrate, and a fermi tapered slot antenna with high-gain and low-side lobe were used for elements of this millimeter-wave passive imaging system. Two dimensional antenna arrangement on focal plane was achieved in this imaging system.

• Journal of Satellite, Information and Communications
• /
• v.2 no.2
• /
• pp.10-15
• /
• 2007

Small size and low profile antenna for mobile vehicular-top-mounted is needed in satellite communication services such as DBS, Satellite Internet and VSAT. In middle latitudes, the development of an array antenna which has the conformal, low profile and 45 degree beam tilted configuration, and has the high gain with sharp beamwidth, low sidelobe and low loss is required for Ku-band satellite communication. In this paper, in order to meet with these performances, an array antenna consisting of the vertical polarized waveguide longitudinal slots based on the leaky-wave mode of traveling wave antenna is proposed. An array antenna consisting of 16 leaky-wave elements is showing 30 dBi of gain, 4.9 degree of beamwidth, below than -20 dB of sidelobe level, 45 degree of beam tilt angle in center frequency. Feed network designed by waveguide cooperated feed shows good performance of wideband and low loss.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.11
• /
• pp.1668-1670
• /
• 2012

In this paper, a satellite array antenna operates at 12.2GHz~12.75GHz was designed and fabricated. The lowest height and high gain electrical beam tilt was obtained by applying backed slot and sub-reflector widening the distance between the patch and the GND. The simulation and measurement showed good agreements, the electrical beam tilt was $10^{\circ}$, the gain was 26.5dBi, the VSWR was less than 3:1 and the return loss was less than -15dB.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.5 no.3
• /
• pp.101-109
• /
• 2012

Because the installation problem of parabola antenna that is tilted to 45 degree when this antenna is installed at the area of middle latitude, the study on planar antenna in place of parabola antenna is made rapid progess. Especially, The development of the planar antenna for VSAT is needed depending on the increased Ka-band satellite communications. In this paper, in order to meet with these performances, an array antenna consisting of the vertical polarized waveguide longitudinal slots based on the leaky-wave mode of traveling wave antenna is proposed. Especially, for the lower sidelobe level, the design method of the radiation power distribution control using the different slot widths is proposed. An array antenna consisting of 32 leakywave waveguide antennas is showing 35.16 dBi of gain, 2.5 degree of beamwidth at azimuth, below than -30 dB of sidelobe level, 45.8 degree of beam tilt angle in center frequency 30.2 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.273-279
• /
• 2009

In this paper, an antenna which has dipole-like radiation pattern and low profile is proposed. The antenna is composed of four elements slot array based on L-shaped 0.43 $\lambda_g$ slot element. It presents a omni-directional radiation patter in the azimuth plane and has a null toward broad-side direction. In the design, a small mono-pole antenna which acts as a large capacitance element, combined with the partially removed ground plane by four L-shaped slots. As a result, these structure act as a LC resonator for radiation. The measured result shows, the impedance bandwidth(VSWR$\leq$2) of the proposed antenna is 60 MHz(2.35$\sim$2.41 GHz). The measured maximum radiation gain and efficiency of proposed antenna is 0.02 dBi, 56.7 % at center frequency 2.38 GHz, respectively. The proposed antenna can be applied to wireless tan access point system.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.5
• /
• pp.209-215
• /
• 2017

In this paper, an antenna having 2-axes cross monopulse for Ka band millimeter-wave seeker is designed and antenna performance is verified through vacuum-brazing method for fabrication and measurement. Also, by designing and manufacturing a waveguide circulator the antenna including the circulator is measured. Radiating part of the antenna takes optimized slot lengths and offsets from Elliot's array synthesis procedure using the generic algorithm and feeding part for cross monopulse axes uses the folded waveguide to optimize the S-parameter result. Based on this method, the antenna has 33.3 dBi gain, $3.5^{\circ}{\pm}0.5^{\circ}$ beamwidth, below -23 dB SLL through fabricating and measuring. It is found that antenna characteristics is similar to design results.