• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 봄 학술발표회 논문집
• /
• pp.277-284
• /
• 1999

This study describes the influence factors related to slope failure pattern and dimension in the southern Kyounggi area. Intrusive and metamorphic rocks are distributed in the study area. Geological condition, rainfall property and slope geometry are influence on slope failure characteristics in the study we& Geological factors related to slope failure are rock type, geological structure and weathering condition. Because of deep soil (RS-CW) depth of granite region, circular failure type is major failure pattern in granite region. Almost granite slopes with circular or surface failure pattern are failed during heavy rainfall season. But typical wedge failure type related to geological structure factor is a main failure pattern of metamorphic rock slope. Additionally failure dimension is influenced by geological factors and several factors, i.e. natural slope condition, failure type, rainfall intensity and etc. failure height/width ratio and thickness/length ratio of granite slope are 0.88 and 0.23. But the ratios of metamorphic rock slope are 1.36 and 0.19.

• 한국농공학회지
• /
• 제35권3호
• /
• pp.47-62
• /
• 1993

The laboratorv model test was carried out to investigate the behavior of pore water pressure, the critical amount of rainfall for slope failure, the pattern of failure, and the variation of seepage line at the slope with the uniform material of embankment by changing the slope angles and rainfall intensities. The results were was summarised as follows : 1.At the beginning stage of rainfall, the negative pore pressure appeared at the surface of slope and the positive pore pressure at the deep parts. But, the negative one turned into the positive one as the rainfall continued and this rapidly increased about 50 to 100 minutes before the slope failure. 2.The heavier the rainfall intensity, the shorter the time, and the milder the slope, the longer the time took to reach the failure of slope. 3.As the angle of the slope became milder, the critical amount of rainfall for slope failure became greater. 4.Maximum pore water pressure was 10 to 40g/cm$^2$ at the toe of slope and 50 to 90g/cm$^2$at the deep parts. 5.In the respect of the pattern of slope failure, surface failure of slope occurred locally at the toe of slope at the A-soil and failure of slope by surface flow occurred gradually at the top part of slope at the B-soil. 6.As the rainfall continued and the saturation zone in the embankment was formed, the seepage line went rapidly up and also the time to reach the total collapse of slope took longer at the B-soil. 7.As the position of the seepage line went up and the strength parameter accordingly down, the safety factor was 2.108 at the A-soil and 2.150 at the B-soil when the slope occured toe failure. Minimum safety factor was rapidly down to 0.831 at the A-soil and to 0.936 at the B-soil when the slope collapsed totally at the top part of slope.

• 한국재난정보학회 논문집
• /
• 제14권4호
• /
• pp.421-429
• /
• 2018

연구목적 : 본 연구는 기후변화에 따른 강우량 및 강우패턴을 분석하여 강우시 비탈면 거동을 파악하기 위해 강우사상을 합리적으로 적용하여 절토부 비탈면 안정성해석에 활용하고자 수치해석기법을 이용하여 비탈면 높이별, 강우사상별 침투해석을 실시하여 강우사상 및 강우지속시간에 따른 지하수위 변화를 고려한 비탈면 안정성검토를 실시하였다. 연구결과 : 강우사상(Uniform Rainfall, US Army Corps., Huff 4분위법 중 1/4법 및 4/4법)에 따른 화강풍화토 비탈면의 수치해석결과 비탈면이 높을수록 침투된 강우가 지하수위까지 빠르게 도달하지 못하여 지하수위 상승은 작아지고, 비탈면의 안전율도 작게 분석되었다. 결론 : 초기강우강도가 제일 큰 강우패턴 Case 3조건인 Huff 4분위법 중 1/4법에서 지하수위 상승량이 제일 크게 나타났으며, 안전율은 가장 작게 나타났다.

• 한국기계가공학회지
• /
• 제15권4호
• /
• pp.8-15
• /
• 2016

Most machines lose a lot of energy due to friction. Wear due to friction also reduces performance. Therefore, it is important to reduce friction on the surface to improve energy efficiency and decrease wear. Surface texturing refers to making patterns on the surface for reducing friction. There are many surface texturing methods, such as using lasers, abrasive jet machining, and so on. Recently, mechanical manufacturing methods, such as cutting and grinding, have been highlighted. Among them, the grinding method has the advantage of making patterns in large areas quickly. Therefore, it is appropriate for surface texturing on large machines. This paper is a study on the slope change of the surface texturing pattern using grinding. Therefore, we researched the slopes of the patterns corresponding to "spindle speed and feed rate" and "curvature of workpiece surface" using a mathematical model and experiment. As a result, we made a proper mathematical model concerning our research. Therefore, using the mathematical model in this paper, we could predict the slope change of the pattern according to grinding conditions.

• Wind and Structures
• /
• 제32권2호
• /
• pp.115-126
• /
• 2021

The snow cornice mass on the formation zone had triggered avalanches which led to the loss of human life and property. Snow cornice is formed due to flow separation on the leeward side. Effect of lee slope is more prominent in the formation of snow cornices as compared to the windward slope. The analysis of wind flow pattern has been carried out to evaluate the performance of a jet roof. Computational Fluid Dynamics (CFD) analysis of wind flow over a 2D hill model was carried out using RNG based k-∈ turbulence models available in ANSYS Fluent. Effect of varying leeward hill slope (1:2 to 1:6) on flow separation for the given windward slope was observed and a critical slope of 1:4 was found at which the separation zone ceased to exist. The modification of wind flow over a hill due to the installation of jet roof was simulated. It was observed that jet roof had significantly modified the wind flow pattern around hill ridgeline and ultimately snow cornice formation had mitigated. The results of the wind flow pattern were validated with the wind data collected at the experimental site, Banihal Top (Jammu and Kashmir, India). The wind flow simulation over the hill and mitigation of cornice formation by the jet roof has been explained in the present paper.

• 센서학회지
• /
• 제25권6호
• /
• pp.423-430
• /
• 2016

This study used a single metal oxide semiconductor (MOS) sensor to classify the major odorous gases hydrogen sulfide ($H_2S$), ammonia ($NH_3$) and toluene ($C_6H_5CH_3$). In order to classify these odorous substances, the voltage on the MOS sensor heater was gradually reduced in 0.5 V steps 5.0 V to examine the changes to the response by the cooling effect on the sensor as the voltage decreased. The hydrogen sulfide gas showed the highest sensitivity compared to odorless air under approximately 2.5 V and the ammonia and toluene gases showed the highest sensitivity under approximately 5.0 V. In other words, the hydrogen sulfide gas reacted better in the low temperature range of the MOS sensor, and the ammonia and toluene gases reacted better in the high-temperature range. In order to analyze the response characteristics of the MOS sensor by temperature in a pattern, a two-dimensional (2D) x-y pattern analysis was introduced to clearly classify the hydrogen sulfide, ammonia, and toluene gases. The hydrogen sulfide gas was identified by a straight line with a slope of 1.73, whereas the ammonia gas had a slope of 0.05 and the toluene gas had a slope of 0.52. Therefore, the 2D x-y pattern analysis is suggested as a new way to classify these odorous substances.

• 한국의류산업학회지
• /
• 제7권2호
• /
• pp.225-230
• /
• 2005

This research was undertaken to compare basic bodice prototypes for Internet shopping customer, and to select a profitable fit vacant space quantity between clothing and body. A total one hundred of eighteen outfits (4 types of pattern ${\times}$ 9 subjects ${\times}$5 body areas) were constructed with basic bodice drafting method of Japan Bunka Women's University according to nine male body types. Fifty-two experts analysis of the different prototypes as five body area and evaluate the most appropriate ease amount and stabilization of the simulation images on the computer. The experiments with automated methods using simulation image are based on AZ program of TORAY, Japan. Data was analyzed using percentiles, frequency and $X^2$. Taken together, the present result of vacant space quantity and stability evaluation through images shows that there is a significant difference in the size variation of the chest circumference, shoulder slope and waist circumference. In case of ease amount, chest area, shoulder slope, waist area and armhole except neckline area were shown more appropriate on the basic bodice pattern without size change. In case of stabilization, the chest area, shoulder slope and armhole except waist area and neckline area was shown the best on the basic bodice pattern without size change. However the waist area was shown on the basic bodice pattern plus 2 cm, neckline was shown more appropriate on the basic bodice pattern plus 1cm.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제6권6호
• /
• pp.1546-1564
• /
• 2012

Pattern-based query processing has not attracted much attention in wireless sensor network though its counterpart has been studied extensively in data stream. The methods used for data stream usually consume large memory and much energy. This conflicts with the fact that wireless sensor networks are heavily constrained by their hardware resources. In this paper, we use piece wise representation to represent sensor nodes' collected data to save sensor nodes' memory and to reduce the energy consumption for query. After getting data stream's and patterns' approximated line segments, we record each line's slope. We do similar matching on slope sequences. We compute the dynamic time warping distance between slope sequences. If the distance is less than user defined threshold, we say that the subsequence is similar to the pattern. We do experiments on STM32W108 processor to evaluate our strategy's performance compared with naive method. The results show that our strategy's matching precision is less than that of naive method, but our method's energy consumption is much better than that of naive approach. The strategy proposed in this paper can be used in wireless sensor network to process pattern-based queries.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.459-466
• /
• 2002

This study reviews the engineering properties of vegetation as one of all factors to select vegetation species for slope protection. The vegetation species mainly applied in domestic soil slope protection were inspected, and the root properties such as root pattern, root length, root weight, were analyzed. And then direct shear tests on undisturbed fine sand including roots were performed to review the effect of root reinforcement. From these analyses, it was concluded that the engineering properties of vegetation should be considered to select vegetation species for slope protection.

• 한국의류학회지
• /
• 제24권1호
• /
• pp.105-115
• /
• 2000

This study was intended to find body pattern of middle aged women and make new experimental basic pattern for upper-half of the body for them. This experimental pattern on the idea of body pattern analysis was prepared. For experimental pattern, the prototype basic model was chosen with the best qualified D model from the four meaningful existing patterns. After several steps of correction experimental pattern was made. Comparing with basic D model, the new experimental pattern composed of additional bust girth by 1cm, wider back waist by 0.5cm than front waist and additional armhole by 0.5cm keeping the same size for back and front widths. Making a shoulder line up by 3cm the armhole became deeper accordingly and the room for girth has been transferred to length. Front neck girth became deeper downward but back neck girth risen a little bit. Side line of the bodice formed with inward slope taking from the waist line by 2cm. Instead of dart, modified side line slope was more practical by its function and appearance. Abdominal girth which is lower than waist girth by 8.5cm kept in same size with bust girth. Then abdominal girth became more comfortable. New experimental pattern with changes has been examined in function and appearance. In conclusion, the new experimental basic pattern for the middle-aged women has been proved more practical for both in bodice and sleeve than other existing ones in terms of function and appearance.