• Journal of Korean Society of Forest Science
• /
• v.108 no.3
• /
• pp.311-321
• /
• 2019

This study was carried out to establish basic data for the development of slow-moving landslide hazard classes. Mountain slopes in slow-moving landslide areas ranged from $11.8^{\circ}$ to $37.0^{\circ}$ with a mean slope of $23.8^{\circ}$. However, the slope inclination of microtopography in slow-moving landslide areas was slightly different, with a mean slope of $23.5^{\circ}$ ($10.7^{\circ}{\sim}41.5^{\circ}$) compared with the mountain slope. There was a significant difference (p < 0.05) between the contour intervals of microtopography and the contour intervals of the slow-moving landslide areas. Among all the slow-moving landslide areas examined, 14 plots (approximately 38.0%) were classified into landslide hazard class I, 6 plots (approximately 16.0%) into landslide hazard class II, 5 plots (approximately 14.0%) into landslide hazard class III and IV, and 16 plots (approximately 43.0%) into landslide hazard class V, whereas 9 plots (approximately 24.0%) fit the no landslide hazard class.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.1
• /
• pp.49-57
• /
• 2022

In order to efficiently analysis the stability of a slope, measuring the shear strength of soil is needed. The Standard Penetration Test (SPT) is not appropriate for a slope inspection due to cost and weights. One of the ways to effectively measure the N-value is the Dynamic Cone Penetration Test (DCPT). This study was performed to develop a minimized multi-function sensors that can easily estimate CPT values and Volumetric Water Content. N value with multi-fuction sensor DCPT showed -2.5 ~ +3.9% error compared with the SPT N value (reference value) in the field tests. Also, the developed multi-fuction sensor system was tested the correlation between the CPT test and the portable tester with indoor test. The test result showed 0.85 R2 value in soil, 0.83 in weathered soil, and 0.98 in mixed soil. As a result of the field test, the multi-function sensor shows the excellent field applicability of the proposed sensor system. After further research, it is expected that the portable multi-function sensor will be useful for general slope inspection.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.43 no.2
• /
• pp.158-165
• /
• 2016

The purpose of this study was to analyze photoplethysmographic waveforms from pulse oximeter using raw data of red and infrared light and investigate the reference values of parameters (Height, Width50, Maximum slope, Minimum slope, Area) for evaluating pulpal blood flow in maxillary central incisors with normal pulp vitality in children. The study was performed in 30 pediatric patients, aged 7-16 years old, using pulse oximeter (MEKICS Co., Ltd, Korea) combined with a custom-made sensor. The raw data was obtained and recorded by custom-made software and analyzed by LabChart (v.7.3, ADInstruments, Germany) offline. In this study, we analyzed photoplethysmographic waveforms from pulse oximeter applied to maxillary central incisor for assessment of pulpal blood flow and suggested several reference values of young permanent maxillary central incisor with normal pulp. On average, the waveform of red light was higher, stiffer and wider than that of infrared light. Future studies about reference values for other normal teeth and the teeth with impaired pulp vitality are needed.

• The Korean Journal of Ecology
• /
• v.8 no.1
• /
• pp.1-5
• /
• 1985

The plastochron index (PI) provides possibility on studies of the effects of various environmental factors on morphological and physiological development of plants. The PI of Erickson and Michemlini(1957) could be used merely when leaf n is longer an leaf n+1 is smaller than the references length at any time. If both the lengths of leaf n and n+1 are smaller or longer than the reference length, it could not estimated. In this study, the PI of Erickson and Michelini was complemented and the linear patterns according to leaf arrangement was represented, PI is n-(lnLR-lnLn)/(lnLn-lnLn+1). And when both the lengths of leaf n and n+1 are longer than the length of reference, PI is n+1+(ln Ln+1-lnLR)/(lnLn-lnLn+1). The linear model of PI is changed by the various environmental factors and the linear patterns are different according to leaf arrangement. According to leaf arrangement, the equation of the general regression lines is Yin-(i-j)=a-(n-1)(q1+...+qi-1)-(q1+...+qj-1)+rt+$\varepsilon$. Where Y:the logarithmic of the leaf length in question, i:leaf number hang on the one node, n:the number counting from base, q:spacing on the Y-axis, j:0, 1, 2, ..., r:slope, t:time, $\varepsilon$:error.

• Korean Journal of Computational Design and Engineering
• /
• v.7 no.3
• /
• pp.148-156
• /
• 2002

Most Rapid Prototyping (RP) processes adopt a solid Computer Aided Design (CAD) model, which will be sliced into thin layers of constant thickness in the building direction. Each cross-sectional layer is successively deposited and, simultaneously, bonded onto the previous layer; and eventually the stacked layers from a physical part of the model. A new RP process, the transfer-type Variable Lamination Manufacturing process using expandable polystyrene foam sheet (VLM-ST), has been developed to reduce building time and to improve the surface finish of parts with the thick layers and a sloping surface. This paper describes the generation of Unit Shape Layer (USL), the cutting path data of the linen. hotwire cutter for the VLM-ST process. USL is a three-dimensional layer with a thickness of more than 1 mm and a side slope, and it is the basic unit of cutting and building in the VLM-ST process. USL includes data such as layer thickness, positional coordinates, side angles of each layer, hotwire cutting speed, the heat input to the hotwire, and reference shape. The procedure of generating USL is as follows: (1)Generation of the mid-slice from the CAD model, (2)Conversion of the mid-slice into a simply connected domain, (3)Generation to the reference shape for the mid-slice, (4)Calculation of the rotation angle of the hotwire of the cutting system.

• Applied Chemistry for Engineering
• /
• v.26 no.1
• /
• pp.116-119
• /
• 2015

Field-effect transistor (FET)-based ion or biosensors have been intensively studied so far. Among many measurement methods, the variation of the drain current can be induced when ions or biomolecules are interacted with sensing membranes located on the gate insulator of FET. One of typical FET-type sensors is an ion-sensitive field-effect transistor (ISFET) utilized in this study. In ISFET, the voltage is usually applied to the reference electrode instead of the gate voltage. Firstly, the voltage applied to the reference electrode versus the drain current was observed, and the steepest slope in this graph was found. Using this point, the optimized condition was established for the larger variation of the drain current in the saturated region in response to the variation of the input in the dynamic range.

• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.817-823
• /
• 2000

A solid-state electrochemicall cell for sensing CO2 gas was fabricated using a solid electrolyte of Li2CO3-Li3PO4-Al2O3 mixture and a reference electrode of LiMn2O4. The e.m.f. (electromotive force) of sensor showed a good accordance with theoretical Nernst slope (n=2) for CO2 gas concentration range of 100-10000 ppm above 35$0^{\circ}C$. The e.m.f. of sensor was constant regardless of oxygen partial pressure at the high temperature above 0.1 atm. It was, however, a little depended on oxygen partial pressure as the pressure decreased below 0.1 atm. The oxygen-dependency of our sensor gradually disappeared as the operating temperature increased. The sensing behavior of our CO2 sensor was affected by the presence of water vapor, but its effect was small comparing with other sensors.

• Journal of Korean Society on Water Environment
• /
• v.32 no.2
• /
• pp.205-215
• /
• 2016

In order to improve water quality in the Paldang Lake, a riparian vegetation belt, treatment wetland, and artificial floating island were designed for introduction in the upland field, the estuary of tributaries, and the section of water facing mountainous land, respectively. We synthesized vegetation information collected from a reference river and found that herbaceous, shrubby, and tree vegetation zones tended to be dominated by Phragmites japonica, Phalaris arundinacea, etc.; Salix gracilistyla, S. integra, etc.; and S. koreensis, S. subfragilis, and Morus alba, respectively. In our plan, the herbaceous vegetation zone, which is established on floodplains with a high frequency of disturbance, will be left in its natural state. A shrubby vegetation zone will be created by imitating the species composition of the reference river in the ecotone between floodplain and embankment. A tree vegetation zone will be created by imitating species composition on the embankment slope. In the treatment wetland, we plan to create emerged and softwood plant zones by imitating the species composition of the Zizania latifolia community, the Typha orientalis community, the P. communis community, the S. integra community, and the S. koreensis community. The floating island will be created by restoring Z. latifolia and T. orientalis for water purification purposes.

• Journal of the Society of Naval Architects of Korea
• /
• v.38 no.4
• /
• pp.23-29
• /
• 2001

An Obstacle Avoidance System(OAS) of Underwater Vehicle(UV) in diving and steering plane is investigated. The concept of Imaginary Reference Line(IRL), which acts as the seabed in the diving plane, is introduced to apply the diving plane avoidance algorithm to the steering plane algorithm. Furthermore, the distance to the obstacle and the slope information of the obstacle are used for more efficient and safer avoidance. As for the control algorithm, the sliding mode controller is adopted to consider the nonlinearity of the equations of motion and to get the robustness of the designed system. To verify the obstacle avoidance ability of the designed system, numerical simulations are carried out on the cases of some presumed three-dimensional obstacles. The effects of the sonar and the clearance factor used in avoidance algorithm are also investigated. Through these, it is found that the designed avoidance system can successfully cope with various obstacles and the detection range of sonar is proven to bea significant parameter to the performance of the avoidance.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.12
• /
• pp.547-552
• /
• 2002

In this paper, the path loss in domestic terrain environments for IMT-2000 are measured and considered. Domestic terrain environments are classified and received power is measured at 1.9201GHz. In addition, the Path loss is calculated with consideration of the radiation pattern of antennas based on the results of measurement. For the consideration of path loss in domestic terrain environments, each path loss are fitted with the same slope of a reference model as "COST-231 HATA Urban Model", and then both are compared. As a result, all of the path loss in domestic terrain environments are lower than the path loss of a reference model as "COST-231 HATA Urban Model". We found that a difference of path loss in domestic terrain environments and a reference model is 5dB in urban, 8dB in sparse urban, 12dll in dense suburban, 13dB in suburban, 19dB in sparse suburban, and 29dB in road.