• Journal of the Korea Concrete Institute
• /
• v.26 no.5
• /
• pp.573-579
• /
• 2014

Typical composite girder has been composed with conventional concrete deck and steel girder. Recently, ultrahigh-performance-concrete (UHPC) deck is proposed in order to enhance durability and reduce weight of deck as well as to increase stiffness and strength of the composite girder. This study investigates that a headed stud is still compatible as a shear connector for the UHPC deck and steel girder composite beam. Twelve push-out specimens are prepared to evaluate the static strength of stud shear connectors embedded in the UHPC deck. The test program proves that the static strength of the stud shear connectors embedded in UHPC well meets with design codes described in AASHTO LRFD. Chosen experimental variables are aspect ratio of height to diameter of stud, thickness of deck and thickness of concrete cover over the head of stud. From the test program, aspect ratio and cover thickness are investigated to mitigate the regulations of the existing design codes. The minimum aspect ratio and the minimum cover thickness given in AASHTO LRFD are four and 50mm, respectively. This limitation hinders to lower the thickness of the UHPC deck. The results of the experiment program give that the aspect ratio and the cover thickness can be lower down to three and 25mm, respectively. Eurocode-4 regulates characteristic relative slip at least 6mm. However, test results show that stud shear connectors embedded in UHPC provide the characteristic relative slip only about 4mm. Therefore, another measures to increase ductility of stud should be prepared.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.10 no.3
• /
• pp.237-242
• /
• 2016

The major advantage of slip-ring technology in Spiral CT is that it facilitates continuous rotation of the x-ray tube, so that volume data can be acquired from a patient quickly. Not only for such a fast scan, but also for the dose reduction purpose, high signal-to-noise ratio and fast data acquisition system is required. In this study, we have built a multi-channel photodetector and multi-channel data acquisition system for CT application. The detector module consisted of CdWO4 crystal and Si photodiode in 16 channels. For the performance test of the preamplifier stage, both the transimpedance and switched integrator types are optimized for the photodetector modules. Switched integrator showed better noise performance in the limited bandwidth which is suitable for the current CT application. The control sequence for data acquisition and 20 bit ADC is designed with VHDL(Very High Speed Integrated Circuit Hardware Description Language) and implemented on FPGA(Field Programmable Gate Array) chip. Our Si photodiode detector module coupled to CdWO4 crystal showed comparable signal with other commercially available photodiode for CT. Switched integrator type showed higher SNR but narrower bandwidth compared to transimpedance preamplifier. Digital hardware is designed by FPGA, so that the control signal could be redesigned without hardware alteration.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.472-482
• /
• 2019

This paper describes the stabilization of underwater TAS winch system Deploy/Recover operation performance. TAS winch installed on the stern of submarine performs to deploy/recover sensor, towing cable and rope tail which is deployed from the stern and separated from submarine itself. Also TAS winch provides transmission path of power to the sensor and data transmitting/receiving path which data are acquired from underwater environment like sound, depth and temperature. At the step of TAS winch evaluation test, sporadic standstill and rotating speed oscillation phenomenon were occurred. Winch motor provides the available torque to deploy/recover TAS and root cause analysis to the winch motor was done to find exact reason to sporadic malfunction. When winch motor was disassembled, eccentricity of rotor, slip-ring and the other composition part for winch motor were found. These might cause magnetic field distortion. To make TAS winch system more stable and block magnetic field distortion, this paper suggests methods to enhance fixing status installed in winch motor. For reliable data acquisition for TAS winch operation, the deploy/recover function of the improved type of TAS winch was verified in LBTS making similar condition with sea status. At the end of stage, improved type of TAS winch was tested on some functions not only deploy/recover function, but sustainability of TAS operation on specific velocity, steering angle of submarine in the sea trial. Improved type of TAS winch was verified in accordance with design requirement. Also, validity of suggested methods were verified by the sea trial.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.1
• /
• pp.1-7
• /
• 2020

In recent years, cargo lashing has received much importance, to help prevent the sinking of passenger ships due to the failure of vehicle and cargo lashing during the transshipment of cargo. Consequently, the standards for lashing equipment and the structure of car ferries have been revised. According to the current standards, all vehicles loaded on a car ferry sailing in smooth sea areas must be secured if the wind speed and wave height exceed 7 m/s and 1.5 m, respectively. In this study, we measured the roll and pitch of a passenger ship sailing in smooth sea areas, and compared the measurements with the results of the New Strip Method (NSM). The vessel had a maximum pitch of 1.41° and a maximum roll of 1.37° at a wind speed of 6-8 m/s and a wave height of 0.5-1.0 m, and a maximum pitch of 1.49° and a maximum roll of 2.43° at a wind speed of 10-12 m/s and a wave height of 1.0-1.5 m. A comparison of the external forces due to the motion of the hull and the bearing capacity without lashing indicated that the bearing capacity was stronger. This suggests that vehicles without lashing will not slip or fall due to weather conditions. In future, the existing vehicle lashing standards can be revised after measuring the hull motions of various ships, and comparing the external force and bearing capacity, to establish more reasonable requirements.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.6
• /
• pp.895-906
• /
• 2018

The improvement project for school zone in Korea is occurring mostly in kindergartens and elementary schools in which children are mainly active, and is being promoted as part of measures to prevent children's traffic accidents. However, since the study on the essential installation facilities and proper level of safety facilities for School zone is lacking, this study relatively evaluated the efficiency of safety facility installation using DEA (Data Envelope Analysis) and suggested improvement plan. We built the facilities and incident data for 28 school zones in Hwaseong City. Six major facilities (Raised intersection, Raised crosswalk, Protective fence, Skid Proof, Speed hump, Speed cameras) that have proven to be effective in the preceding research were analyzed as input factors. As a result of the analysis, only 12 out of 28 showed efficiency and 16 out of efficiency. Effective groups of school zones were found to have fewer installed Protective fences, Skid Proof, and Speed cameras installations than school zones classified as ineffective groups. Protective fences were found to be efficient even if only 47% of the total extension of the school zone was installed, and the number of slip prevention facilities was 8.7 per square km. The number of subjects to be compared is 28, so this study is limited to use as a relative efficiency evaluation index, and it can be grouped into nationwide units and efficiency evaluation can be done for each group.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.6D
• /
• pp.587-597
• /
• 2010

When a car accident occurs, people who had an accident are not free from civil and criminal issues so that the accident investigator should reenact and analyze the accident situation accurately. In addition, the obtained documents through the analysis of such car accident occurrence and related factors have to be used to carry out the improvement of the areas that has numerous car accidents and complementary actions. The vehicle speed, accelerating force, braking power are currently known as the most affecting factors in accordance with many car accidents, traffic facilities, road design, etc. The vehicle's performance and rode friction coefficient road surface friction coefficient are affecting the most closely in this field. Especially, once the estimate of the speed of the accident moment relating to main eleven articles of Traffic Accident Exemption Law is very important and accuracy is required. However, currently the researches of these matters have not made exclusively yet in Korea. In this study by reflecting this current situation, until the sudden braking history is found from the car's sudden braking, it estimates accurately the transient brake time and rode friction coefficient by measuring a time of transient brake time through the precision speed detector (Vericom VC2000PC). The analysis of the experimental results calculated the transient brake time and friction coefficient to fit into the purpose of this study in the basis of different kind of various special purpose asphalt pavement and slip-prevention pavement and provided the fundamental data.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.179-182
• /
• 2008

It needs to consider of turns during a path-finding on real road network. Because a car is delayed by waiting a traffic signal and decreasing speed when drived in a turn road such as cross road and slip road. If a straightness of a path is increased, a real cost of traveling should be able to decrease. An older method, the algorithm with Turn Heuristic, considered of this case. The algorithm, that differently gave weights to left, right and U-turns, improved a straightness of a path, but increased a cost of exploring. In this paper, we propose a improved Turn Heuristic Algorithm. Proposed algorithm uses Dynamic Turn Heuristic. It is able to more decrease a cost of exploring than older method by using the Turn Heuristic in a part of path-finding.

• The Korean Journal of Rheology
• /
• v.11 no.1
• /
• pp.57-65
• /
• 1999

In order to measure yield stress of PIM feedstocks simply and effectively, a yield stress measuring technique was developed by a vane method. The vane method had an advantage that there was no wall-slip, while it had a drawback that it could not measure viscosity change at various shear rates. A Newtonian fluid was tested for the appropriateness of the measuring technique. The end effect of a vane was checked to produce an acceptable error. The torque peak has been considered to be developed at yielding of non-Newtonian fluids with yield stress. However, it was influenced very much by control system of the instrument so that the torque value at the stable region was taken to calculate yield stress. Torque at zero rotational speed was obtained by extrapolating the torque values at various speeds to remove the effect of the rotational drag. As general verification, yield stress of feedstocks made of Tungsten carbide powder with wax-based binder was measured at different temperatures and various powder concentrations.

• International Journal of Highway Engineering
• /
• v.13 no.3
• /
• pp.103-110
• /
• 2011

This study deals with the traffic accidents by type. The objectives are to analyze the characteristics of 2 accident types, and to develop the models by type. In pursuing the above, this paper gives particular attentions to testing the differences between by type two groups, and developing the models (Poisson and negative binomial regressions) using the data of domestic circular intersections. The main results are as follows. First, the number of accidents in vehicle vehicle was analyzed to account for about 73.41% of total and to be higher than vehicle people. Second, two Poisson models and two negative binomial models which were all statistically significant were developed using vehicle people accidents and vehicle vehicle accidents as dependant variables. Finally, the traffic volume as common variable was selected in the models, and right-turn slip lane, speed hump, the number of driveways, the number of pedestrian crossings as specific variables of the models were selected.

• The Journal of Engineering Geology
• /
• v.19 no.3
• /
• pp.287-294
• /
• 2009

To be design the slope, the area distributed the mica schist which was metamorphosed by shale or mudstone must carefully consider the stability. Mica schist is another unstable rock for slope by schistosity, cleavage, axial plane of a fold etc. In general mica schist contains the swelling clay minerals such as smectite, vermiculite and montmorillonite. These minerals make the slope unstable. At OO tunnel construction area for the rail way of the Kyungbu high speed train, the slope of mica schist is very unstable by the distribution phenomena of the discontinuous plane such as joints which are 1-5 cm spacing and thrust and strike-slip fault. By the drilling core of this area, most RQD have 0-20%.