• 한국자동차공학회논문집
• /
• 제18권2호
• /
• pp.122-128
• /
• 2010

To meet the NOx limit without a penalty of fuel consumption, urea-SCR system is currently regarded as promising NOx reduction technology for diesel engines. SCR system has to achieve maximal NOx conversion in combination with minimal $NH_3$ slip. In this study, the performance characteristics of urea-SCR system with open loop control were assessed in the European Transient Cycle(ETC) for heavy duty diesel engine. The SCR inlet temperaure varied in the range of 200 to $340^{\circ}C$ in the ETC cycle. Open loop control calculated the urea flow rate based on the NOx and NSR map which gave for each combination of SCR inlet temperature and space velocity the normalized $NH_3$ to NOx stoichiometric ratio which resulted in a steady-state $NH_3$ slip of 20ppm. During the ETC cycle, the open loop control with the optimized NSR offset achieved NOx reduction of 80% while keeping the average $NH_3$ slip below 10ppm and maximum 20ppm. It was also found that NOx sensor was cross-sensitive to $NH_3$ and a control strategy for cross-sensitivity compensation was required in order to use a NOx sensor as feedback device.

• 동력기계공학회지
• /
• 제11권3호
• /
• pp.16-21
• /
• 2007

Three dimensional numerical study was carried out to investigate the effect of aspect ratio on microchannel flow. We considered five straight rectangular channels with aspect ratios (height/width) 0.2, 0.4, 0.6, 0.8 and 1.0. Nitrogen gas flow was investigated for both slip and noslip wall boundary conditions. Isothermal wall condition was assumed. We used control volume method for this simulation. The slip velocity increases with the increase of aspect ratio. Friction coefficient decreases with the increase of aspect ratio. Slip friction coefficient is lower than noslip friction coefficient. Mass flow rate of slip model is higher than that of noslip model. We compared our results with the experimental result reported in the literature. The agreement was good.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.299-300
• /
• 2007

In this paper, slip wear phenomenon of train was studied by traction force of acceleration and braking force of deceleration. First, the slip wear phenomenon on train operation mode was analyzed when powering, coasting and braking each and then rail wear was analyzed from the slip wear data. Especially, the data proved correlation between slip wear and deceleration rather than acceleration. Second, If velocity of a train is constant, even though the velocity is high, ATO logging data and measurement data proved that the rail wear is not serious. It will help for efficient braking force operation providing fundamental data to braking step control.

• Multiscale and Multiphysics Mechanics
• /
• 제1권3호
• /
• pp.261-270
• /
• 2016

The longitudinal velocity (forward speed) having significant importance in proper running of railway wheelset on track, depends greatly upon the adhesion ratio and creep analysis by implementation of suitable dynamic system on contamination. The wet track condition causes slip and slide of vehicle on railway tracking, whereas high speed may also increase slip and skidding to severe wear and deterioration of mechanical parts. The basic aim of this research is to design appropriate model aimed estimator that can be used to control railway vehicle forward velocity to avoid slip. For the filtration of disturbance procured during running of vehicle, the kalman filter is applied to estimate the actual signal on preferered samples of creep co-efficient for observing the applied attitude of noise. Thus error level is detected on higher and lower co-efficient of creep to analyze adhesion to avoid slip and sliding. The skidding is usually occurred due to higher forward speed owing to procured disturbance. This paper guides to minimize the noise and error based upon creep coefficient.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 B
• /
• pp.405-407
• /
• 2000

The most generally implemented method to detect the ground speed of the railway vehicles is to use the rotary type speed sensor attached to wheel axle. The Slip or sliding phenomenon on the railway vehicles occurs frequently caused by the weak viscosity of the wheel. Thus, precisely to control the car, the slip/sliding detection system is required. In this paper we proposed for the speed data management system, which uses rotary type speed sensor. Proposed speed management system can detect the slip/sliding with wheel axle as well as correct the generated speed error during in error time, to provide accurate speed and precise location data. The effectiveness for adapting to the railway system is clarified by the computer simulation.

• 한국터널지하공간학회 논문집
• /
• 제21권6호
• /
• pp.811-823
• /
• 2019

최근에는 수직구 구조물 시공방법으로 현장타설 공법 대비 시공속도가 빠르며, 안전하고 경제적인 연속상승 슬립폼 공법이 다수의 현장에 적용되고 있다. 슬립폼 공법으로 시공 가능한 높이는 2.5~4 m/day로 알려져 있는데, 콘크리트 온도가 10~30℃의 범위 밖에서는 강도 변화나 탄성 특성의 변화에 미치는 영향이 크므로 동절기 공사에서는 3 m/day 이상의 시공속도를 내기가 어렵다. 또한, 콘크리트는 수화 작용으로 인해 수화열이 발생하는데, 이는 콘크리트의 온도 균열을 초래한다. 따라서 슬립폼 연속상승시 콘크리트의 온도 제어 양생이 필요하며, 본 연구에서는 히팅 패널 및 시험용 연속상승 장치를 개발하여 반발경도, 초음파 전파시간, 수화열 및 외부온도를 측정하였다. 이를 기반으로 히팅슬립폼을 제작하였으며, "김포 현장"과 "신월 현장"에 히팅슬립폼을 적용하였다. 김포현장은 주간(08:00~17:30) 평균 1.9 m/day 또는 0.200 m/hr, 신월 현장은 2.0 m/day 또는 0.210 m/hr를 목표 상승속도 값으로 비교하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.891-895
• /
• 2004

This paper suggests the techniques in determining the values of the steady-state equivalent circuit parameters of a three-phase squirrel-cage induction machine using immune algorithm. The parameter estimation procedure is based on the steady state phase current versus slip and input power versus slip characteristics. The proposed estimation algorithm is of a nonlinear kind based on clonal selection in immune algorithm. The machine parameters are obtained as the solution of a minimization of least-squares cost function by immune algorithm. Simulation shows better results than the conventional approaches.

• 한국자동차공학회논문집
• /
• 제10권3호
• /
• pp.201-208
• /
• 2002

In this paper, the control strategy of ratio changing system for a metal belt CVT adopting primary pressure regulation is developed, and the shirting performance of pressure regulating type CVT with the suggested control strategy is investigated. The control strategy suggested in this study is composed of 2 feedback loop, one is speed ratio feedback and the other is primary pressure feedback. The pressure feedback is adopted to ensure prohibiting a belt slip during transient period in a fast downshift mode. Simulation results show that the system with suggested control strategy gives appropriate response time and tracking Performance for upshift and also gives a proper primary pressure which can prohibit the belt slip. In addition, it is fecund that the given system has an acceptable servo property in tracking the target speed ratio and robustness for the disturbance of line pressure.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.523-530
• /
• 2005

This paper addresses sliding mode control (SMC) of the anti-lock braking system (ABS) with a compensator of model uncertainties such as vehicle parameter variation, unmodeled dynamics, and external disturbances. A sliding mode controller (SMC) is designed with a nominal vehicle model to achieve a desired wheel slip ratio. A disturbance observer (DOB) is introduced to compensate the model uncertainties and is designed with a transfer function of a hydraulic brake dynamics. Through simulations on the model uncertainties, it is verified that the sliding mode control with the DOB can give the simulation results better than the sliding mode control without the DOB.

• 전력전자학회논문지
• /
• 제10권5호
• /
• pp.494-500
• /
• 2005

본 논문에서는 플라이휠에너지를 이용한 다이나믹 UPS 시스템에서 유도기를 이용하여 플라이휠의 에너지를 저장 및 재생하는 시스템 제어 기법을 제시하였다. 유도발전기의 슬립주파수 제어와 벡터제어 기법의 특성을 비교하고, 또한 벡터제어 기법을 사용 시 전동 모드에서 발전 모드로의 전환할 때 직류링크 커패시터 전압의 과도 특성을 개선하는 기법을 개발하였다. 32비트 DSP를 사용한 실험을 통하여 이 기법의 성능을 확인하였다.