• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2000년도 춘계학술강연 및 발표대회 강연 및 발표논문 초록집
• /
• pp.9-10
• /
• 2000

An important business-field of world-wide steel-industry is the coating of thin metal-sheets with zinc, zinc-aluminum and aluminum based materials. These products mostly go into automotive industry. in particular for the car-body. into building and construction industry as well as household appliances. Due to mass-production, the processing is done in large continuously operating plants where the mostly cold-rolled metal-strip as the substrate is handled in coils up to 40 tons unwind before and rolled up again after passing the processing plant which includes cleaning, annealing, hot-dip galvanizing / aluminizing and chemical treatment. In the liquid Zn, Zn-AI, AI-Zn and AI-Si bathes a combined action of corrosion and wear under high temperature and high stress onto the transfer components (rolls) accounts for major economic losses. Most critical here are the bearing systems of these rolls operating in the liquid system. Rolls in liquid system can not be avoided as they are needed to transfer the steel-strip into and out of the crucible. Since several years, ceramic roller bearings are tested here [1.2], however, in particular due to uncontrollable Slag-impurities within the hot bath [3], slide bearings are still expected to be of a higher potential [4]. The today's state of the art is the application of slide bearings based on Stellite\ulcorneragainst Stellite which is in general a 50-60 wt% Co-matrix with incorporated Cr- and W-carbides and other composites. Indeed Stellite is used as the bearing-material as of it's chemical properties (does not go into solution), the physical properties in particular with poor lubricating properties are not satisfying at all. To increase the Sliding behavior in the bearing system, about 0.15-0.2 wt% of lead has been added into the hot-bath in the past. Due to environmental regulations. this had to be reduced dramatically_ This together with the heavily increasing production rates expressed by increased velocity of the substrate-steel-band up to 200 m/min and increased tractate power up to 10 tons in modern plants. leads to life times of the bearings of a few up to several days only. To improve this situation. the Mechanical Alloying (MA) TeChnique [5.6.7.8] is used to prOduce advanced Stellite-based bearing materials. A lubricating phase is introduced into Stellite-powder-material by MA, the composite-powder-particles are coated by High Energy Milling (HEM) in order to produce bearing-bushes of approximately 12 kg by Sintering, Liquid Phase Sintering (LPS) and Hot Isostatic Pressing (HIP). The chemical and physical behavior of samples as well as the bearing systems in the hot galvanizing / aluminizing plant are discussed. DependenCies like lubricant material and composite, LPS-binder and composite, particle shape and PM-route with respect to achievable density. (temperature--) shock-reSistibility and corrosive-wear behavior will be described. The materials are characterized by particle size analysis (laser diffraction), scanning electron microscopy and X-ray diffraction. corrosive-wear behavior is determined using a special cylinder-in-bush apparatus (CIBA) as well as field-test in real production condition. Part I of this work describes the initial testing phase where different sample materials are produced, characterized, consolidated and tested in the CIBA under a common AI-Zn-system. The results are discussed and the material-system for the large components to be produced for the field test in real production condition is decided. Outlook: Part II of this work will describe the field test in a hot-dip-galvanizing/aluminizing plant of the mechanically alloyed bearing bushes under aluminum-rich liquid metal. Alter testing, the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed. Part III of this project will describe a second initial testing phase where the won results of part 1+11 will be transferred to the AI-Si system. Part IV of this project will describe the field test in a hot-dip-aluminizing plant of the mechanically alloyed bearing bushes under aluminum liquid metal. After testing. the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed.

• Tribology and Lubricants
• /
• 제31권1호
• /
• pp.6-12
• /
• 2015

This paper investigates the stick-slip characteristic of magnetorheological elastomer (MRE) between an aluminum plate and the surface of the MRE. MRE is a smart material and it can change its mechanical behavior with the interior iron particles under the influence of an applied magnetic field. Stick-slip is a movement of two surfaces relative to each other that proceeds as a series of jerks caused by alternate sticking from friction and sliding when the friction is overcome by an applied force. This special tribology phenomenon can lead to unnecessary wear, vibration, noise, and reduced service life of work piece. The stick-slip phenomenon is avoided as far as possible in the field of mechanical engineering. As this phenomenon is a function of material property, applied load, and velocity, it can be controlled using the characteristics of MRE. MRE as a soft smart material, whose mechanical properties such as modulus and stiffness can be changed via the strength of an external magnetic field, has been widely studied as a prospective replacement for general rubber in the mechanical domain. In this study, friction force is measured under different loads, speed, and magnetic field strength. From the test results, it is confirmed that the stick-slip phenomenon can be minimized under optimum conditions and can be applied in various mechanical components.

• 대한기계학회논문집A
• /
• 제37권5호
• /
• pp.625-630
• /
• 2013

본 연구는 직경 45 nm인 원통형 나노동공을 가진 산화알루미늄(AAO) 박막에 오일을 함침시켰을때 동점도가 마찰 마멸에 미치는 영향을 규명하고자 실시하였다. 양극산화법으로 제조한 AAO 박막을 직경 1 mm의 440C 스테인리스 강구를 상대재로 하여 왕복동 미끄럼 접촉시험을 실시하였다. 마찰면과 마멸입자는 주사전자현미경과 에닥스(Energy-dispersive X-ray)를 이용해 분석하였다. 높은 동점도 오일의 윤활효과가 저점도 오일에 비해 크게 향상되었다. 동점도가 낮은 경우엔 모든 하중조건에서 심한 마찰흔적과 함께 두꺼운 소성변형층이 넓게 형성되었으며 경계윤활막의 손상으로 접촉면에 물질전이와 화학적 반응 현상이 모두 발생하였다. 오일의 점도가 높은 경우 마찰면에 존재하는 경계윤활막이 파괴되지 않아 마찰흔적과 소성변형층의 형성이 매우 적었으며 물질전이와 화학적 반응이 방지되었다.

• 한국산학기술학회논문지
• /
• 제15권3호
• /
• pp.1253-1258
• /
• 2014

CA 이온도금기술에 의한 TiC와 TiN 그리고 TiC/TiN 코팅재를 비교하기 위하여 트라이볼로지 물성을 연구하였다. 실험은 Falex journal V block 시스템을 이용한 터보시험기에서 수행하였다. 코팅재의 마찰과 마모특성은 작용된 하중과 미끄럼 속도에 의하여 다양하게 결정되었다. TiC와 TiN 그리고 TiC/TiN 코팅재는 표면에서 트라이볼로지 특성이 현저하게 증가하였다. 단층코팅에서는 TiC보다 TiN이 좋은 결과를 얻었다. 그러나, TiC/TiN의 다층코팅은 다른 어떤 단층코팅보다 좋은 성능을 보였다. 다층코팅의 성능이 향상된 핵심요소는 TiN층 외부와 강 사이에서 부착이 증가하게된 TiC의 역할 때문이다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.356-356
• /
• 2010

Tribological behaviors of the hard film on soft substrate system were explored using the hard thin film of diamond-like carbon (DLC) coated the soft polymer of polydimethysiloxane (PDMS). A DLC film with the Young's modulus of 100 GPa was coated on PDMS substrate with Young's modulus of 10 MPa using plasma enhanced chemical vapor deposition (PECVD) technique. The deposition time was varied from 10 sec to 10 min, resulting in nanoscale roughness of wrinkle patterns with the thickness of 20 nm to 510 nm, respectively, at a bias voltage of $400\;V_b$, working pressure 10 mTorr. Nanoscale wrinkle patterns with 20-100 nm in width and 10-30 nm height were formed on DLC coating due to the residual stress in compression and difference in Young's modulus. Nanoscale roughness effect on tribological behaviors was observed by performing a tribo-experiment using the ball-on-disk type tribometer with a steel ball of 6 mm in diameter at the sliding speed of 220 rpm, normal load of 1N and 25% humidity at ambient temperature of $25^{\circ}C$. Friction force were measured with respect to thickness change of coated DLC thin film on PDMS. It was found that with increases the thickness of DLC coating on PDMS, the coefficient of friction decreased by comparison to that of the uncoated PDMS. The wear tracks before and after tribo-test were analyzed using SEM and AFM.

• Composites Research
• /
• 제19권2호
• /
• pp.28-34
• /
• 2006

고온자전합성법과 스파크 플라즈마 소결법으로 여러 가지 $TiB_2$ 함유량을 갖는 $Cu-TiB_2$ 금속복합재료를 제조하였다. 점용접 전극과 미끄럼 접촉재로 사용하기 위해 인장특성, 경도, 마모저항 등의 물성치를 조사하였다. 강화재의 형상, 크기, 부피분율 등에 의해 복합재료의 특성이 달라지므로 유효물성치를 예측하기 위한 모델링이 필수적이다. 유한요소해석결과 유효탄성 계수가 실험치와 일치하는 것을 확인하였고 Eshelby 모델, Mori-Tanaka의 평균장 이론이 결합된 Eshelby 모델, 혼합법칙 등으로 복합재료의 탄성계수를 예측한 결과 Mori-Tanaka의 평균장 이론이 결합된 Eshelby 모델이 실험치를 사장 잘 묘사하는 것으로 나타났다.