• Steel and Composite Structures
• /
• 제4권1호
• /
• pp.37-48
• /
• 2004

This paper deals with the strength and deformation of both short and slender concrete filled steel tubular columns under the combined actions of axial compression and bending moment. Sixteen specimens were tested to investigate the effect of fiber reinforced concrete on the ultimate strength and behavior of the composite column. The primary test parameters were load eccentricity and column slenderness. Companion tests were also undertaken on eight numbers of similar empty steel tubes to highlight the synergistic effects of composite column. The test results demonstrate the influence of fiber reinforced concrete on the strength and behavior of concrete filled steel tubular columns.

• 한국공간구조학회논문집
• /
• 제4권1호
• /
• pp.87-95
• /
• 2004

본 논문은 화재시 온도상승에 따른 H-형강 기둥의 내력에 관한 연구이다. 주요 매개변수는 온도, 세장비와 하중비이다. 온도 상승시 강재의 물리적 특성은 EC3 Part1.2에 따랐다. 온도상승에 따른 국부좌굴의 임계온도는 재료의 항복강도와 판폭두께비가 클수록 더 낮아진다. 균등한 열을 받는 철골 기둥의 내혁 평가는 LRFD에 따른 축력과 강축 및 약축 모멘트에 대하여 고려하였다.

• Structural Engineering and Mechanics
• /
• 제23권5호
• /
• pp.563-577
• /
• 2006

This study involves a series of experiments on the buckling strength of eccentrically compressed cold-formed stainless steel square hollow-section columns. The principal parameters in this study are slenderness ratios ($L_k/r$ = 30, 50, 70) and magnitude of eccentricity e (0, 25, 50, 75, 100 mm) on the symmetrical end-moment. The objectives of this paper are to obtain the buckling loads by conducting a series of experiments and to compare the behavior of the eccentrically compressed cold-formed stainless steel square hollow-section columns with the results of the analysis. The ultimate buckling strength of the square-section members were determined with the use of a numerical method in accordance with the bending moment-axial force (M-P) interaction curves. The behavior of each specimen was displayed in the form of a moment-radian (M-${\theta}$) relationship. The numerically obtained ultimate-buckling interaction curves of the beam columns coincided with the results of the experiments.

• 대한기계학회논문집A
• /
• 제31권10호
• /
• pp.1025-1030
• /
• 2007

Three kinds of metallic sandwich panels with quasi-Kagome truss cores have been analyzed on their mechanical behaviors subjected to bending load. According to the results of previous work on the optimal design, they were designed to have similarly high strength per weight with the identical overall sizes, i.e., the total length, the width, the core height. Differences were in the face sheet thickness and/or the thickness of the metal sheet from which the core was fabricated through expanding and bending processes. Under the bending load, they performed well as designed, as far as the maximum load is concerned. However, after the maximum load, the load-displacement curves were different each other depending on the slenderness ratio of the truss elements composing the quasi-Kagome truss cores and the face sheet thickness. Namely, the slenderness ratio and the face sheet thickness governed stability of the elastic and plastic buckling. Therefore, if energy absorption characteristics or structural stability as well as the maximum load capacity are to be achieved, the sandwich panel with thick truss members and thick face sheet should be selected.

• 한국기계가공학회지
• /
• 제1권1호
• /
• pp.38-47
• /
• 2002

Machining quality has been improved with the development of cutting tools. However, it is difficult to obtain a high degree of quality in machining a deep pocket with a long end mill, since machining accuracy is mainly dependent on the stiffness of the cutting tool and tool holder. To improve machining quality in machining a deep pocket using an end mill, the performance by cutting condition compare with others. Owing to this problem, it is necessary to select suitable tool and holder in the deep pocket machining. In this study, the hydraulic holder for the high speed machining is introduced and the performance of that is compared with others according to cutting conditions. The cutting parameters involved were; slenderness ratio in the range of 3 to 6 (L/D), radial depth of cut from 0.01 to 0.05 mm. Cutting force and surface roughness, precision of form were observed during the experiment to investigate cutting state.

• 한국강구조학회 논문집
• /
• 제15권1호
• /
• pp.9-15
• /
• 2003

최근 건축물의 고층화 및 장스팬화 됨에 따라서 부재단면이 점차 증대되서 용접시공 등이 어려워지고 있다. 이에 대한 해결방안의 하나로 고강도강을 사용하면 부재단면을 감소시킬 수 있다. 고강도강의 주 사용 부위은 높은 축력을 받는 기둥재이다. 휨모멘트와 축력을 동시에 받는 박스형 및 H형 단면을 갖는 고강도 기둥부재의 성능실험을 축력과 세장비를 변수로 수행하였다. 실험 결과 기둥부재의 최대내력이 허용응력도 설계법과 한계상태 설계법을 모두 만족하였다.

• Geomechanics and Engineering
• /
• 제8권1호
• /
• pp.53-66
• /
• 2015

Plastic wastes, particularly polyethylene terephthalate (PET) generated from used bottled water constitute a worldwide environmental issue. Reusing the PET waste for geotechnical applications not only reduces environmental burdens of handling the waste, but also improves inherent engineering properties of soil. This paper investigated factors affecting shear strength improvement of PET-mixed residual soil. Four variables were considered: (i) plastic content; (ii) plastic slenderness ratio; (iii) plastic size; and (iv) soil particle size. A series of unconfined compression tests were performed to determine the optimum configurations for promoting the shear strength improvement. The results showed that the optimum slenderness ratio and PET content for shear strength improvement were 1:3 and 1.5%, respectively. Large PET pieces (i.e., $1.0cm^2$) were favorable for fine-grained residual soil, while small PET pieces (i.e., $0.5cm^2$) were favorable for coarse-grained residual soil. Higher shear strength improvement was obtained for PET-mixed coarse-grained residual soil (148%) than fine-grained residual soils (117%). The orientation of plastic pieces in soil and frictional resistance developed between soil particles and PET surface are two important factors affecting the shear strength performance of PET-mixed soil.

• Steel and Composite Structures
• /
• 제22권2호
• /
• pp.217-234
• /
• 2016

In order to investigate mechanical properties and load-bearing capacity of T-shaped Concrete-Filled Square Steel Tubular (TCFST) composite columns under eccentric axial load, three T-shaped composite columns were tested under eccentric compression. Experimental results show that failure mode of the columns under eccentric compression was bending buckling of the whole specimen, and mono column performs flexural buckling. Specimens behaved good ductility and load-bearing capacity. Nonlinear finite element analysis was also employed in this investigation. The failure mode, the load-displacement curve and the ultimate bearing capacity of the finite element analysis are in good agreement with the experimental ones. Based on eccentric compression test and parametric finite element analysis, the calculation formula for the equivalent slenderness ratio was proposed and the bearing capacity of TCFST composite columns under eccentric compression was calculated. Results of theoretical calculation, parametric finite element analysis and eccentric compression experiment accord well with each other, which indicates that the theoretical calculation method of the bearing capacity is advisable.

• Steel and Composite Structures
• /
• 제7권1호
• /
• pp.19-34
• /
• 2007

This paper presents results of a non-linear finite element analysis of axially loaded slender hollow structural section (HSS) columns, strengthened using high modulus carbon-fiber reinforced polymer (CFRP) longitudinal sheets. The model was developed and verified against both experimental and other analytical models. Both geometric and material nonlinearities, which are attributed to the column's initial imperfection and plasticity of steel, respectively, are accounted for. Residual stresses have also been modeled. The axial strength in the experimental study was found to be highly dependent on the column's imperfection. Consequently, no specific correlation was established experimentally between strength gain and amount of CFRP. The model predicted the ultimate loads and failure modes quite reasonably and was used to isolate the effects of CFRP strengthening from the columns' imperfections. It was then used in a parametric study to examine columns of different slenderness ratios, imperfections, number of CFRP layers, and level of residual stresses. The study demonstrated the effectiveness of high modulus CFRP in increasing stiffness and strength of slender columns. While the columns' imperfections affect their actual strengths before and after strengthening,the percentage gain in strength is highly dependent on slenderness ratio and CFRP reinforcement ratio, rather than the value of imperfection.

• 한국전산구조공학회논문집
• /
• 제15권1호
• /
• pp.105-116
• /
• 2002

이 논문에서는 철근콘크리트 장주의 극한저항력을 효과적으로 산정할 수 있는 설계 관계식이 제안되었다. 철근콘크리트 기둥의 거동은 여러 설계변수들의 영향을 받는데 특히 콘크리트의 강도, 철근비, 세장비 및 편심 등에 의해 크게 영향을 받으므로 설계식의 제안을 위해 위의 4가지 변수들을 변화시켜가며 철근콘크리트 기둥의 비선형 해석을 수행하였다. 콘크리트의 균열 등을 포함한 재료의 비선형성을 고려하기 위해 적층단면법이 사용되었으며, p-△ 효과를 구현하기 위하여 기하강성행렬이 고려되었다. 해석결과로부터 각 변수의 변화에 따른 철근콘크리트 기둥의 저항력의 변화를 비교하였으며 이를 토대로 회귀분석 모델을 제안하였다. 또한 회귀분석을 수행하여 철근콘크리트 장주의 극한저항력을 효과적으로 산정할 수 있는 회귀분석식을 제안하였고, 기존의 설계기준과 비교하여 제안식의 효율성을 검증하였다.