• 동력기계공학회지
• /
• 제11권2호
• /
• pp.51-57
• /
• 2007

As a shot sleeve in die casting plays a critical role in delivering molten metal to a die cavity, any disruption to its function in the injection stage results in deterioration of the quality of final castings. To guarantee a smooth operation of a shot sleeve, its structural stability should be maintained. Despite the simple geometry, design of shot sleeve is based on individual engineer's experience and no agreement on the design is present. In this study, we newly propose a systematic methodology to determine a minimum wall thickness of a shot sleeve to prevent yielding or plastic deformation. Analytical calculations incorporating numerical analysis produce a rational design rule for minimum thickness of a shot sleeve subject to metal intensification pressure and geometric die constraint. To validate the proposed design guideline, authors present real data on a collection of actual shot sleeves. Upon checking their conformity to the new design rule, we discovered a strong correlation between the design of wall thickness and premature failures.

• 한국기계가공학회지
• /
• 제14권1호
• /
• pp.29-35
• /
• 2015

In this study, a FEM analysis is undertaken of a rubber sleeve which is mounted onto a spreading mandrel so as to avoid marking the first wrappings of coils (known as the 'end-mark'), as occasionally occurs when a concentrated load is placed on the edge of a steel sheet, significantly reducing its quality. A commercial numerical package, ANSYS, was utilized to analyze the structural behavior of the rubber sleeve. In general, the strain of the sleeve increases as the thickness of the rubber layer (H) covering the tubes increases, thus also increasing the surface of the sleeve for a constant boundary condition, and decreasing the pitch (P) between each tube, resulting in an increase in the strain on the surface of the sleeve for all rubber thickness conditions tested here. In a comparison of two different materials, rubber and urethane, when H=3 mm and P=1.1D, the maximum total deformations in these cases are 0.12669 mm and 0.086623 mm, respectively.

• 한국의류학회지
• /
• 제23권3호
• /
• pp.353-360
• /
• 1999

An investigation made of the variations of angle of bias on the top of the sleeve cap curve line and calculated easing contraction ratio by capheights(A ; a,h$\times$5,/6) B: A, H/4 +4cm C:A.H/3 D: A.H/ 4+3cm E:AH/4+2cm, F: A,H/4+1cm, G: A,H/4, H:A,H/6, I:A,H/8) and the efects of easing contraction on the cap curve lines of sleeve A, D, G by easing stitch density with the gathering foot: sewing condition-lockstitch industrial machine stitch density(N1.0 ; 38stitches/3cm N1.5: 26stitches/3cm, N2.0 ; 19stitches/3cm, N2.5 ; 14stitches/ 3cm) The results obtained were as follows; 1) The variations of the angle of bias on the top of the sleeve cap curve line by cap heights can be done according to the angle balance (front; $\alpha$-$\beta$ back ; $\alpha$'- $\beta$') between the angle (front ;$\alpha$, $\beta$, back ; $\alpha$'- $\beta$') of bias of the two base-lines. 2) The higher cap height the more higher the calculated easing contraction ratio. 3) The lower the stitch density the higher easing contraction ratio. 4) The effects of easing contraction was that sleeve G was more than sleeve A, D.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권1호
• /
• pp.61-66
• /
• 2014

The evaporative cooling technology used in Wind generator stator has unique advantages. Combined with the structure of motor stator and operating conditions, this report based on the research project for the evaporative cooling sleeve of the 3.6MW wind generator, introduces the material requirements and structural characteristics of the sleeve, simulates on the stress, displacement and stability by finite analysis method, and tests the products experimentally. The research results show that the epoxy resin-glass materials have a higher strength and better insulation properties, but the evaporative cooling of the wind generator stator sleeve, because of its thin-walled, and the external pressure, so it's the less rigid. Should make full use of the motor stator core structure, increase its stiffness and improve the stability of the epoxy resin-glass sleeve, which for thin-walled the epoxy resinglass sleeve on the successful application of wind turbines has played an important role.

• 해양환경안전학회지
• /
• 제27권1호
• /
• pp.145-152
• /
• 2021

본 연구의 목적은 슬리브 이음된 배관 사이의 간극과 Re가 변할 때 배관 내의 유동은 어떻게 변하는지 조사함으로써 조정관 설치 시에 압력손실과 난류 강도를 감소시킬 수 있는 배관 간극(Lp)을 파악하는 것이다. 슬리브 이음된 배관 두께(tp)는 5 mm로 고정하고 Lp는 10, 50, 100 및 200 mm로 하여 슬리브 이음부의 속도, 압력 분포, 재순환 영역에서의 재부착점 길이 및 Re와의 상관관계를 해석하였다. 상용 프로그램인 Ansys fluent 18.1을 이용하였고, Re의 범위는 200 ≤ Re ≤ 5,000으로 하여 층류에서 난류까지 슬리브 이음부의 유동 특성을 파악하였다. 슬리브 이음부의 확대비와 축소비는 각각 1.2와 0.83이였고 Lp가 일정할 때 Re가 커질수록 슬리브 하류 가장자리(edge)의 난류 강도와 압력 변화가 크게 나타났다. 이는 슬리브 벽면에서의 유동이 tp에 의해 흐트러지고 속도 에너지의 손실이 발생하면서 슬리브 이음부의 가장자리에 영향을 미친 것으로 판단된다. Lp가 10 mm 이하의 경우, Re가 증가함에 따라 가장자리의 난류 강도에는 큰 변화가 없었다. 재순환 영역에서의 재부착점은 Lp가 10 mm 이하에서 나타나지 않았으며 와(vortex)의 영향도 없었다. 3,000 ≤ Re의 경우, Lp가 증가함에 따라 슬리브 이음부 벽면에서의 재부착점 길이는 거의 일정하였다.

• Journal of Chest Surgery
• /
• 제44권6호
• /
• pp.413-417
• /
• 2011

Background: Sleeve lobectomy for lung cancer in close proximity to or involving the carina is widely accepted. Operative morbidity and mortality rates, recurrence, and survival rates have varied considerably across studies. Materials and Methods: From March of 2005 to July of 2010, sleeve lobectomy was performed in 19 patients and pneumonectomy was performed in 20 patients. In this paper, the results of sleeve lobectomy and pneumonectomy for patients with lung cancer will be compared and evaluated. Results: There were no postoperative complications in either group, but there was one mortality in the pneumonectomy group. There was better preservation of pulmonary function in the sleeve lobectomy group than the pneumonectomy group (p=0.066 in FVC, p=0.019 in FEV1). The 3-year survival rates were 46.7% in the sleeve lobectomy group and 54.5% in the pneumonectomy group (p=0.505). The 3-year disease-free survival rates were 38% in the sleeve lobectomy group and 45.8% in the pneumonectomy group (p=0.200). Conclusion: Sleeve lobectomy for lung cancer showed low mortality, low bronchial anastomotic complication rates, and good preservation of pulmonary function.

• Journal of Chest Surgery
• /
• 제25권10호
• /
• pp.1132-1136
• /
• 1992

We report a successful right,sleeve pneumonectomy using femoro-femoral bypass on a 26-year-old woman with severe carinal and lower tracheal stenosis of tuberculous origin. Omental graft on the anastomotic site was added, There was no specific postoperative complication and postoperative bleeding was minimal.

• 한국의류학회지
• /
• 제27권2호
• /
• pp.219-228
• /
• 2003

The purpose of this study were to examine the characteristics of arm types proposed in the previous study and to present sleeve patterns according size and shape of 4 arm types. 31 direct and indirect items were measured. The subjects for this study were 132 females of twenties. The results were as follows. 1. All of the direct measurements showed significant difference by the arm types. especially at the front armhole part. Such a.: the items of arm gradients, armhole sizes belong to the indirect measurements made clear difference also. 2. By the discriminant analysis, 9 items including underarm length, front armhole girth, upper arm girth, degree of elbow point-wrist point discriminated arm type by the hit ratio of 90.4% Item related to shape of arm rather than size made a sharp distinction. 3. Through the examination of existing patterns and wearing tests on the subjects among 4 groups, sleeve patterns classified by the arm type were suggested.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.519-526
• /
• 1997

The purpose of this study is to develop the analytical model for the reinforcement bar connection in group-filled steel pipe sleeve, which consists of beam elements for the reinforcement bar and shell elements for the sleeve and the mortar and spring elements for the bond stress-slip relationship. In the reinforcement bar connection using grout-filled steel pipe sleeve, the major variables are the bond stiffness between reinforcement bar and mortar($K_1$) and between sleeve and mortar($K_2$). It is nearly difficult to predict the exact bond stiffness with the experimental results. Therefore, The linearly elastic analyses using ABAQUS, FEM package show the validity of the mathematical equations for the bond stiffness and the choice of material elements in this paper. To predict the behaviour between yield and ultimate tensile strength, the nonlinear analyses must be performed henceforth.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 학술대회 논문집
• /
• pp.405-408
• /
• 2005

This paper presents the characteristics of antenna factors for sleeve dipole antennas with a broad bandwidth. The coupled integral equations for the unknown current distributions on each elements are derived and solved by applying Galerkin's method of moments. The flatness of antenna factor is considered by variation of the length and number of sleeve elements.