• 대한조선학회논문집
• /
• 제53권1호
• /
• pp.45-53
• /
• 2016

The interaction between the hull of ship and free surface of water generates important loads during slamming motion. In the present study, the slamming load applied on the sectional surface of two-dimensional arbitrary bodies has been investigated under several falling velocities. This simulation has been done with the commercial CFD software ANSYS FLUENT^®. Through the conventional MARINTEK experiments for the benchmark of the simulation, we verified the impact pressure values between the experiments and simulation results. Two arbitrary ship bow section models, Panamax-like(with small convex bulb and flare) and Post panamax-like(with large convex bulb and flare) are also investigated. Simulation results show that a maximum impact pressure on the Post panama-like shape is higher than the Panamax-like shape. According to both a lump of water generated by arbitrary shape and various dead-rise angles of the shape, the pressure picks were enhanced in the simulation.

• Ocean Systems Engineering
• /
• 제6권2호
• /
• pp.143-159
• /
• 2016

Cargo, such as a Tension Leg Platform (TLP), Semi-submersible platform (Semi), Spar or a circular Floating Production Storage and Offloading (FPSO), are frequently dry-transported on a Heavy Lift Vessel (HLV) from the point of construction to the point of installation. The voyage can span months and the overhanging portions of the hull can be subject to frequent wave slamming events in rough weather. Tie-downs or sea-fastening are usually provided to ensure the safety of the cargo during the voyage and to keep the extreme responses of the cargo, primarily for the installed equipment and facilities, within the design limits. The proper design of the tie-down is dependent on the accurate prediction of the wave slamming loads the cargo will experience during the voyage. This is a difficult task and model testing is a widely accepted and adopted method to obtain reliable sea-fastening loads and extreme accelerations. However, it is crucial to realize the difference in the inherent stiffness of the instrument that is used to measure the tri-axial sea fastening loads and the prototype design of the tie-downs. It is practically not possible to scale the tri-axial load measuring instrument stiffness to reflect the real tie-down stiffness during tests. A correlation method is required to systematically and consistently account for the stiffness differences and correct the measured results. Direct application of the measured load tends to be conservative and lead to over-design that can reflect on the overall cost and schedule of the project. The objective here is to employ the established correlation method to provide proper high-frequency responses to topsides and hull design teams. In addition, guidance for optimizing tie-down design to avoid damage to the installed equipment, facilities and structural members can be provided.

• 해양환경안전학회지
• /
• 제11권2호
• /
• pp.77-82
• /
• 2005

지금까지 국내에서 제작된 요트는 선체의 재질이 FRP로 제작되어 왔으나 FRP는 환경오염 및 해양안전에 관한 법규 규제가 강화되고 있는 국제사회의 인식에 따라 중소형 조선소를 중심으로 강철 재료나 알루미늄 재료들 사용한 선박건조로 변화하고 있는 실정이다. 강선요트의 구조상 강선재료를 주로 사용함으로서 여러 가지 강도적인 측면에 대한 검토가 필요하지만, 소형선박이므로 종강도, 횡강도 부분은 규정에서의 허용 응력치에 안전율(Safe Factor)만을 주어서 설계를 하여도 충분히 안정된 구조를 이를 수가 있다. 그러나, 소형선박에서 가장 문제시되는 것은 국부강도(Local Strength)의 평가이다. 본 구조해석에서는 선수에 작용하는 슬래밍 동작하중 및 선수충격에 의한 선수부의 손상 여부와 선수부의 국부강도 만족 여부를 확인하고, 기관받침(Engine bed) 부분에서의 중량하중과 횡파하중에 대한 검토를 수행하였다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제10권4호
• /
• pp.520-528
• /
• 2018

This paper presents the results of experimental investigation on the elastic-plastic response of steel unstiffened wedges with dead-rise $10^{\circ}$ subjected to repeated impulsive pressure loadings. Repeated drop tests were performed with both wedge thickness and drop height varied. The pressure and histories were recorded during the tests and the permanent deflections were measured after every drop. Using the recorded test result, the effects of flexibility of wedges and repetition have been investigated. From the pressure history obtained from the tests the characteristics of the impulses were identified. Numerical simulations of the tests were made using the measured pressure history and the permanent deflection predictions were compared with those of the experiments.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.583-591
• /
• 2005

The ship plating is generally subjected to combined in-plane load and lateral pressure loads. In-plane loads include axial load and edge shear, which are mainly induced by overall hull girder bending and torsion of the vessel. Lateral pressure is due to water pressure and cargo. These load components are not always applied simultaneously, but more than one can normally exist and interact. Hence, for more rational and safe design of ship structures, it is of crucial importance to bitter understand the interaction relationship of the buckling and ultimate strength for ship plating under combined loads. Actual ship plates are subjected to relatively small water pressure except for the impact load due to slamming and panting etc. The present paper describes an accurate and fast procedure for analyzing the elastic-plastic large deflection behavior up to the ultimate limit state of ship plates under combined loads. In this paper, the ultimate strength characteristics of plates under axial compressive loads and lateral pressure loads are investigated through ANSYS elastic-plastic large deflection finite element analysis with varying lateral pressure load level.

• International Journal of Ocean System Engineering
• /
• 제2권3호
• /
• pp.151-159
• /
• 2012

The characteristics of an impact load and pressure were experimentally investigated. Drop tests were carried out using a modified Wigley with CB = 0.56. The vertical force, pressures, and vertical accelerations were measured. A 6-component load cell was used to measure the forces, piezo-electric sensors were used to capture the impact pressure, and strain-gauge type accelerometers were used to measure the vertical accelerations. A 50-kHz sampling rate was applied to capture the peak values. The repeatability of the measured data was confirmed and the basic characteristics of the impact load and pressure such as the linearity to the falling height were observed for all of the measurements. A simple formula was derived to extract the physical impact load from the measured force based on a simple mass-sensor-mass diagram, which was validated by comparing impact forces with existing data using the mathematical model of Faltinsen and Chezhian (2005). The effects of the elasticity of the model and change in acceleration during the water entry were investigated. It is interesting to observe that the impact loads occurred and reached peak values at the same time duration after water entry for all drop heights.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제12권1호
• /
• pp.213-225
• /
• 2020

Floating Offshore Wind Turbines (FOWT) installed in the deep sea regions where stable and strong wind flows are abundant would have significantly improved energy production capacity. When designing FOWT, it is essential to understand the stability and motion performance of the floater. Water tank model tests are required to evaluate these aspects of performance. This paper describes a model test and numerical simulation for a 750-kW semi-submersible platform wind turbine model-II. In the previous model test, the 750-kW FOWT model-I suffered slamming phenomena from extreme wave conditions. Because of that, the platform freeboard of model-II was increased to mitigate the slamming load on the platform deck structure in extreme conditions. Also, the model-I pitch Response Amplitude Operators (RAO) of simulation had strong responses to the natural frequency region. Thus, the hub height of model-II was decreased to reduce the pitch resonance responses from the low-frequency response of the system. Like the model-I, 750-kW FOWT model-II was built with a 1/40 scale ratio. Furthermore, the experiments to evaluate the performance characteristics of the model-II wind turbine were executed at the same location and in the same environment conditions as were those of model-I. These tests included a free decay test, and tests of regular and irregular wave conditions. Both the experimental and simulation conditions considered the blade rotating effect due to the wind. The results of the model tests were compared with the numerical simulations of the FOWT using FAST (Fatigue, Aerodynamics, Structures, and Turbulence) code from the National Renewable Energy Laboratory (NREL).

• 한국산학기술학회논문지
• /
• 제22권2호
• /
• pp.733-738
• /
• 2021

최근 국내 해양레저에 대한 국민들의 관심이 높아지고 있고, 해외 시장 개척을 위한 레저선박 건조 및 제조업체들의 연구개발이 활발한 실정이다. 기존 레저보트에 많이 사용되어 온 재료 중에서 FRP와 알루미늄합금은 각각 장기간 사용으로 인한 흡습성과 재활용이 불가능한 환경문제와, 높은 열전도도와 고열에 약해 화재에 취약하다는 단점을 가지고 있다. 따라서 본 연구에서는 높은 비강도와 내식성을 갖춘 티타늄합금을 선체 재료로 선택하였고, 선박의 구조설계를 위해 충격하중에 의한 설계하중을 4가지 규정으로부터 산정하고, 이 하중에 대응하는 선체 판두께를 추정하였다. 국제표준인 ISO 12215-5, 이탈리아선급인 RINA Pleasure Yacht, 영국선급인 LR Special Service Craft, 한국선급인 KR 고속경구조선규칙을 비교 분석한 결과, 최대 슬래밍하중은 ISO, KR, LR, RINA의 크기 순서로 높게 계산되었고, 요구되는 판 두께도 ISO, KR, LR, RINA의 크기 순서로 추정되었다. 레저보트는 국제 규정에 적합한 설계와 인증이 필수적이므로, 각 규정에 대한 사용자의 이해를 높이고 해외 수출 선박의 설계 및 승인 절차에 도움이 되리라 생각한다.

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2018년도 공동국제학술발표회
• /
• pp.193-193
• /
• 2018

현재 우리나라는 레저선박 및 중소형 선박, 연안소형어선에 대부분 사용되는 재질은 강도가 높고 내양품성이 우수한 FRP를 사용하고 있다. 하지만 FRP선박의 폐선 시 환경문제와 자원재활용, 선체중량에 연비 및 대기오염등에 의해 소형선박 중심으로 알루미늄선 전환이 이루어지고 있다. 본 연구에서는 알루미늄 선체가 적용된 멀티하우스보트에 알루미늄선 구조기준에 따른 슬래밍하중을 적용하여 구조 강도평가를 실시하였으며, 그 결과를 통해 각 부재별 민감도 평가를 수행하여 알루미늄 구조강도기준을 만족함과 동시에 중량 저감을 하여 실제 선박설계에 적용시키고자 한다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권4호
• /
• pp.1148-1159
• /
• 2014

Different procedures for estimation of the extreme global wave hydroelastic responses in ships are discussed. Firstly, stochastic procedures for application in detailed numerical studies (CFD) are outlined. The use of the First Order Reliability Method (FORM) to generate critical wave episodes of short duration, less than 1 minute, with prescribed probability content is discussed for use in extreme response predictions including hydroelastic behaviour and slamming load events. The possibility of combining FORM results with Monte Carlo simulations is discussed for faster but still very accurate estimation of extreme responses. Secondly, stochastic procedures using measured time series of responses as input are considered. The Peak-over-Threshold procedure and the Weibull fitting are applied and discussed for the extreme value predictions including possible corrections for clustering effects.