• Journal of Advanced Research in Ocean Engineering
• /
• 제4권4호
• /
• pp.204-216
• /
• 2018

A ship repeatedly face free surface under rough sea conditions owing to relative motion with wave encounter. The impact pressure is transferred to the hull structure and causes structural damage. In this study, the bow flare slamming load of a container ship is estimated using computations fluid dynamics (CFD) and prescript formula according to various classifications. It is found that the bow flare slamming load calculated by the formulas of the common structural rule and ABS tends to be similar to the CFD results.

• Ocean Systems Engineering
• /
• 제10권2호
• /
• pp.163-179
• /
• 2020

Considering the huge demand of several types of subsea equipment, as Christmas Trees, PLEMs (Pipeline End Manifolds), PLETs (Pipeline End Terminations) and manifolds for instance, a critical phase is its installation, especially when the equipment goes down through the water, crossing the splash zone. In this phase, the equipment is subject to slamming loads, which can induce impulsive loads in the installation wires and lead to their rupture. Slamming loads assessment formulation can be found in many references, like the Recommended Practice RP-N103 from DNV-GL (2011), a useful guide to evaluate installation loads. Regarding to the slamming loads, RP-N103 adopt some simplifying assumptions, as considering small dimensions for the equipment in relation to wave length, in order to estimate the slamming coefficient C_S used in load estimation. In this article, an experimental investigation based on typical subsea structure dimensions was performed to assess the slamming coefficient evaluation, considering a more specific scenario in terms of application, and some reduction of the slamming coefficient is achieved for higher velocities, with positive impact on operability.

• 해양환경안전학회지
• /
• 제25권4호
• /
• pp.489-497
• /
• 2019

거친 해상 조건에서 운항하는 선박은 파도와의 상대운동으로 인해 슬래밍 하중에 노출된다. 특히 선수가 자유수면으로 입수하는 과정에서 선체부는 일시적으로 큰 슬래밍 충격하중을 받게된다. 일반적으로 대형 컨테이너선박의 경우, 큰 플레어를 가지는 특징이 있으며, 이로 인해 플레어 슬래밍 충격하중으로 인한 구조적 손상이 발생할 수 있다. 본 연구에서는 슬래밍 수치시뮬레이션을 위해 먼저 신뢰할 만한 실험결과와의 비교검증을 수행하였으며, 선수 및 사파에서 선수플레어 슬래밍 하중을 추정하였다. 그 결과 슬래밍 하중이 발생되는 위치는 0.975st이며, 최대 충격 하중은 선수파 조건에서 약 475kPa임을 확인하였다.

• Journal of Advanced Research in Ocean Engineering
• /
• 제4권4호
• /
• pp.195-203
• /
• 2018

The wave impact on ships could cause local damage to the ship's hull, which has been a concerning issue during the ship design process. In recent years, local structural damages of ships caused by slamming loads have been reported by accident; therefore, it is necessary to study the local slamming pressure loads and structural response assessment. In the present study, slamming loads around the ship's bow region in the presence of regular wave have been simulated by RANS equations discretized with a cell-centered finite volume method (FVM) in conjunction with the $k-{\Box}$ turbulence model. The dynamic structural response has been calculated using an explicit FE method. By adding the slamming pressure load of each time step to the finite element model, establishing the reasonable boundary conditions, and considering the material strain-rate effects, the dynamic response prediction of the bow flare structure has been achieved. The results and insights of this study will be helpful to design a container ship that is resistant enough to withstand bow flare slamming loads.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제12권1호
• /
• pp.518-530
• /
• 2020

The present study concerns the stern slamming load of container carriers, with stern bulb arrangement variation. First, a series of wedge drop tests were conducted using simple wedge models with fixed deadrise angles, and tests with the cross-section models of practical container carrier sterns were followed. The deadrise angle of the simple wedge ranged from 0° to 10°. The pressure measurement results of the simple wedge drop tests were distributed between empirical formula and analytic solution, so the experimental setup was validated. In the cases of practical hull cross-sections, the water entry of the bulb prior to that of the transom resulted in characteristic water film generation and delayed pressure peak appearance. The trapped air between the bulbs damped the pressure in the twin skeg hull case, reducing the pressure peak and causing the pressure oscillation during water entry.

• 대한조선학회논문집
• /
• 제44권3호
• /
• pp.279-284
• /
• 2007

As a container vessel becomes larger, the bow flare becomes larger. The large bow flare structures are often subjected to dynamic pressure loads due to bow flare slamming occurring in rough seas. The aim of this paper is to investigate the characteristics of bow flare slamming pressure measured in a real voyage through the North Pacific Ocean. The characteristics of impact pressure load caused by slamming is addressed in terms of the pressure pulse-time history which involves rising time, peak pressure, decaying time and type of pressure decay. The values were presented using non-dimensional parameters.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제10권3호
• /
• pp.294-306
• /
• 2018

Most offshore structures including offshore wind turbines, ships, etc. suffer from the impulsive pressure loads due to slamming phenomena in rough waves. The effects of elasticity & plasticity on such slamming loads are investigated through wet free drop test results of several steel unstiffened flat bottom bodies in the rectangular water tank. Also, their cumulative deformations by consecutively repetitive free drops from 1000 mm to 2000 mm in height are measured.

• 한국해양공학회지
• /
• 제19권4호
• /
• pp.15-20
• /
• 2005

This paper presented the development of a new experimental and numerical technique for the investigation of slamming impact. The in-house code was developed, based on the boundary element method. The application of commercial code was attempted using FLUENT. Pneumatic cylinder and LM-guide were introduced to closely simulate the free fall phenomenon. It was demonstrated that the proposed experimental and numerical studies can be useful tools in investigating slamming phenomenon.

• 대한조선학회논문집
• /
• 제52권5호
• /
• pp.418-424
• /
• 2015

This paper is about the bow structure design of the ship-typed and turret moored FPSO which is subjected to the bow-flare slamming load in harsh North Sea environments. Quad 204 FPSO project involves the redevelopment of the existing Schiehallion FPSO which is damaged by impact wave loads. Normally all offshore systems including FPSO are designed to withstand the 100 year storm I.e. the storm that happens once every hundred years at the location where the system is installed. Several incidents have revealed that impact loading is important issue for moored floating production systems. In this paper, the design impact loads are estimated considering the ship owner’s specification, measured data from model tests, requirements of the classification society rules and results of numerical simulation analyses. The impact pressure by numerical analysis is 1.8 times greater than required value by CSR adopted by IACS. Based on the selected design load, plastic design formulae allowing the local material yielding are applied for the initial scantling of the bow structure. To verify the structural integrity, FE analyses are carried out considering the local area subjected to the impact wave loads. Their results such as structural arrangement, design loads and scantlings are shown and discussed. It is found that plastic design formulae in adopting Initial design phase give sufficiently conservative results in terms of structural strength.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.183-186
• /
• 2003

This paper presents the results of slamming experiment using air pressure cylinder to increase the repeatability of the experiment. When it comes to the slamming experiment, the traditional way of doing it has been the free fall experiment. By adopting air pressure cylinder almost equal peak pressures were obtained with that of free fall experiment. Jet takes place when the wedge enters water. Slamming doesn't take place when Dead rise angle is more then 20 degrees.