• 한국대기환경학회지
• /
• 제19권2호
• /
• pp.133-143
• /
• 2003

Numerous evidence have been reported that fine particulate matters can play an important role in threatening human health. Recently concerns on fine particle pollution from various engines may require re-examination of particulate emission standards. The particles emitted by most diesel engines are mainly divided into their size ranges such as Dp< 50 nm and 50 nm< Dp< 1,000 nm. In this work, the number concentration and the size distribution of fine particles emitted from an exhaust manifold of a railroad diesel engine were measured under load test conditions using a scanning mobility particle sizer (SMPS). The fine particles observed were within the range of 7 to 304 nm under different load conditions with two different dilution ratios. The fine particles exhibited unique patterns showing bimodal shapes in size distribution.

• 한국주조공학회지
• /
• 제16권6호
• /
• pp.556-564
• /
• 1996

Variation of shape and size of solid particles and solute redistribution in Mg-9wt.%Al, AI-4.5wt.% Cu, and AI-7wt.%Si alloys were investigated when they were heated to semi-solid temperatures and held without stirring. In the case of Mg-9wt.% Al and Al-4.5wt.%Cu alloys, the polygonal shaped solid particles were agglomerated with non-uniform distribution, and there were no disappearance of the solid/solid boundary until the end of melting. But in the case of an Al-7wt.%Si alloys, two or three spherical shaped particles were coalesced or separated individually, and the coalesced particles had no solid/solid interface on the contrary to the prevous case. The maximum size of solid particles during isothermal heating at high temperature was smaller than that at lower temperature, but the time required to reach the maximum size at high temperature was shorter than that at lower temperature. The concentrations of main solute atom whose distribution coefficient is lower than 1, decreased in the primary solid particles as the liquid fraction increased, and the gradient of solute concentration was steeper in Mg-9wt.%Al alloy and Al-4.5wt.%Cu alloy than that of Al-7wt.%Si alloy.

• 대한기계학회논문집A
• /
• 제38권9호
• /
• pp.1013-1018
• /
• 2014

자기연마가공은 연마입자와 자성입자를 혼합한 공구의 유연성을 이용하여, 공작물 표면을 폴리싱하는 특수가공법이다. 기존 연구의 대부분은 가공 정밀도를 향상시키기 위해서 연마입자의 크기를 달리 하는 것에 관한 내용들이다. 그러나 자기연마 가공에서는 연마입자의 크기뿐만 아니라, 자성입자의 크기도 가공에 많은 영향을 미칠 것으로 판단되며 이에 대한 연구가 반드시 필요하다. 따라서 본 연구에서는 크기가 다른 자성입자들을 사용하여 자기연마가공의 효과를 평가하였다. 자성입자는 철분말을 사용하였으며, 직경이 평균 8, 78, $250{\mu}m$의 크기이다. 공작물의 표면거칠기 향상 정도를 비교하여 자성입자의 크기가 자기연마가공의 정밀도에 미치는 효과를 평가하였다. 자성입자의 크기는 표면거칠기의 향상에 많은 영향을 미치며, 직경이 $78{\mu}m$일 때 가장 좋은 표면거칠기의 향상을 나타내었다.

• Journal of the Korean Wood Science and Technology
• /
• 제51권5호
• /
• pp.334-344
• /
• 2023

Dregs from the sugar palm (Arenga pinnata) starch industry are considered a waste product of the agricultural industry and have not yet been optimally utilized. Therefore, this study aimed to manufacture particleboards from dregs using different amounts of adhesive and particle size ratios. Sugar palm dregs, which had been separated into fibers and powder/fine particles, were used as raw material for making particleboards. The fiber had an average length of 6.84 ± 3.23 cm, while the fine particles were of a size that passed through size 10 mesh and remained in size 60 mesh. Three ratios of fiber to fine particles (100:0, 75:25, and 50:50 wt%) with three different amounts of sucrose-citric acid adhesive (10, 15, and 20 wt%) were used in this study. Increasing the amount of fine particles and the resin content can improve the physical properties and the internal bond strength of boards made from sugar palm dregs. The fine particles possibly filled the gap between the fibers in the particleboard, while the fibers exhibited a high bending strength. As a result, a high-performance particleboard can be attained by combining the composition ratio of fiber/fine particles and resin content. In this study, particleboards made from fiber/fine particles (75:25 wt%) and adhesive content of 15 wt% and 20 wt% had the mechanical properties that met the requirements of Japanese Industrial Standard (JIS) A 5908 type 18. Sugar palm dregs have the potential to be used as raw materials to create value-added particleboards.

• 천문학회보
• /
• 제42권2호
• /
• pp.48.3-49
• /
• 2017

Interplanetary space of the solar system contains a large number of dust particles, referred to as Interplanetary Dust Particles (IDPs) cloud complex. They are observable through meteors and zodiacal lights. The relative contribution of possible sources to the IDPs cloud complex was an controversial topic, however, recent research (Yang & Ishiguro, 2015 and references therein) suggested a dominance of cometary origin. In this study, we numerically investigated the orbital evolution of cometary dust particles, with special concerns on different evolutionary tracks and its consequences according to initial orbits, size and particle shape. The effect of dust particle density and initial size-frequency distribution (SFD) were not decisive in total cloud complex mass and mass supply rate, when these physical quantities are confined by observed zodiacal light brightness and dust particle SFD at 1 au. We noticed that, if we assume the existence of fluffy aggregates discovered in the Earth's stratosphere and the coma of 67P/Churyumov-Gerasimenko, the required mass supply rate decreases significantly. We also found out that close encounters with planets (mostly Jupiter) are the dominating factor of the orbital evolution of dust particles, as the result, the lifetime of cometary dust particles are shorter than Poynting-Robertson lifetime (around 250 thousand years). As another consequence of severe close encounters, only a small fraction of cometary dust particles can be transferred into the orbit < 1 au. This effect is significant for large size particles of ${\beta}$ < 0.01. The exceptional cases are dust particles ejected from 2P/Encke and active asteroids. Because they rarely encounter with Jupiter, most dust particles ejected from those objects are governed by Poynting-Robertson effect and well transferred into the orbits of small semimajor axis. In consideration of the above effects, we directly estimated probability of mutual collisions between dust particles and concluded that mutual collisions in the IDPs cloud complex is mostly ignorable, except for the case of large sized particles from active asteroids.

• Journal of Korean Society for Atmospheric Environment
• /
• 제22권E1호
• /
• pp.45-48
• /
• 2006

Mass size distributions of atmospheric particles in Cheonan were determined using a high volume air sampler equipped with a 5-stage cascade impactor. Bimodal distributions that are typical for urban atmospheric particles were obtained. A MMD of the fine particle mode was $0.47{\pm}0.05{\mu}m$ with a GSD of $2.72{\pm}0.21$, and those of the coarse particles were $5.15{\pm}0.18{\mu}m\;and\;2.09{\pm}0.09$, respectively. The annual average concentrations of TSP, PM10, PM2.5, and PM1 were 74.1, 67.5, 54.2, and $42.3{\mu}g/m^3$, respectively. Although the daily PM10 concentrations were under the current National Standard, the daily PM2.5 concentrations frequently exceeded the US Standard even in non asian dust periods. The fractions of PM 10, PM2.5, and PM1 in TSP were $0.905{\pm}0.013,\;0.723{\pm}0.022,\;and\;0.572{\pm}0.029$, respectively, and fine mode particles occupied $57{\sim}72%$ of the total particle mass. The results indicate that fine particles were at the concerning level, and should be the target pollutant for the regional air quality strategy in Cheonan.

• 공업화학
• /
• 제17권1호
• /
• pp.12-15
• /
• 2006

본 연구의 목적은 물유리에 의해 제조된 실리카 미립자의 평균입도와 입도분포에 미치는 반응조건, 용매 및 계면활성제의 영향을 조사하는 것이다. 실리카 미립자는 다양한 종류의 계면활성제와 분산용매를 사용하는 에멀젼법에 의해 제조하였다. 계면활성제로는 비이온성인 Span 20, Span 40, Span 60 및 Span 80을 사용하였으며, 분산용매로는 알킬그룹인 n-Hexane, n-Heptane, iso-Octane 및 n-Decane을 사용하였다. 실험결과에 의하면 유화교반속도에 따른 실리카 미립자의 평균 입경은 교반속도가 증가함에 따라 감소하였으며, 일정한 입경의 에멀젼을 형성하기 위한 최적의 유화교반시간은 약 6 min임을 알 수 있었다. 생성된 실리카 미립자의 평균입경은 사용된 용매의 분자량이 증가함에 따라 감소하며, 사용한 계면활성제의 hydrophobic lipophilic balance(HLB) 값이 감소함에 따라 증가하였다.

• 공업화학
• /
• 제25권5호
• /
• pp.526-530
• /
• 2014

2,2'-Bis[4-(3,4-dicarboxyphenoxy) phenyl]propane dianhydride와 3,5-diamniobenzoic acid의 반응에 의해 얻어진 폴리에테르아미드산을 안정제로 사용하여 스티렌을 분산중합하여 폴리스티렌-폴리에테르아미드산 코어-셀 입자를 얻었다. 폴리에테르아미드산의 결합 효율을 증가시키기 위하여 4-vinylbenzyltrimethylammonium chloride를 공단량체로 사용하였다. 에탄올-물(7 : 3) 혼합용액을 반응매질로 사용했을 때 입자의 안정성 가장 높았고 입자의 크기도 비교적 균일하였다. 폴리스티렌-폴리에테르아미드산 코어-셀 입자의 크기는 스티렌의 양에 비례하여 증가하였다. Dimethylformamide-물 혼합용액에서 중합한 경우에는 입자의 크기 분포가 넓어졌다. 폴리스티렌-폴리에테르아미드산 코어-셀 입자의 셀을 화학적으로 이미드화 하여 폴리스티렌-폴리에테르이미드 코어-셀 입자로 변환시켰다.

• 반도체디스플레이기술학회지
• /
• 제22권4호
• /
• pp.1-6
• /
• 2023

In CO₂ laser surface machining of plastic films in modern display manufacturing, scattering of fume particles could be a major source of well-recognized film surface contamination. This computational fluid dynamics research investigates the suction air flow patterns over a film surface as well as the dispersion of micron-sized fume particles with low-Reynolds number particle drag model. The numerical results show the recirculatory flow patterns near laser machining point on film surface and also over the surface of vertical suction slot, which may hinder the efficient removal of fume particles from film surface. The dispersion characteristics of fume particles with various particle size have been tested systematically under different levels of suction flow intensity. It is found that suction removal efficiency of fume particles heavily depends on the particle size in highly nonlinear manners and a higher degree of suction does not always results in more efficient particle removal.

• 멤브레인
• /
• 제20권2호
• /
• pp.87-96
• /
• 2010

세공 크기가 2.6 ${\mu}m$인 SPG (Shirasu porous glass) 막이 설치된 실험실 규모의 막유화 장치를 사용하여 막유화 에멀젼-겔 공정의 변수 조절을 통해 구형상의 실리카 입자를 제조하였다. 막유화 에멀젼-겔 공정의 변수로는 분산상 압력, 연속상 내 안정제 및 유화제의 농도, $H_2O$/TEOS 비율 및 연속상에 대한 분산상의 비율로 설정하고, 이들 변수가 제조된 실리카 입자의 크기와 분포에 미치는 영향을 검토하였다. 막유화의 공정변수들 중에서 분산상 압력과 연속상에 대한 분산상의 비가 증가할수록 실리카 입자의 크기가 증가하였다. 반면 안정제 및 유화제의 농도, $H_2O$/TEOS 비가 증가할수록 입자의 크기가 감소하였다. 막유화 에멀젼-겔 공정변수의 조절을 통해 최종적으로 평균 입자 크기가 3 ${\mu}m$인 비교적 입도분포가 균일한 구형상의 실리카 입자 제조가 가능하였다.