• Composites Research
• /
• 제25권6호
• /
• pp.172-177
• /
• 2012

저저항 Si-SiC 소결체 제조를 위해 ${\alpha}$-SiC에서 조성과 C의 양을 변화시키면서 반응소결 특성을 고찰하였다. 시료준비는 정수압으로 성형체를 제조하였고, 용융Si 반응소결을 통해 시험편을 준비하였다. 반응소결체의 미세구조, 기계적 특성 및 전기저항 분석 결과 용융Si과 반응 후 미립의 ${\beta}$-SiC가 생성되었고, 치밀한 소결체를 형성하였다. 미립 ${\beta}$-SiC 생성량은 카본 양 에 따라 증가하였다. 그리고 C함량 10wt%이내에서 기계 R전기저항특성은 입도조성 영향이 크고 카본 함량 10wt%이상에서는 상전이 반응의 영향이 큼을 알 수 있었다.

• 한국세라믹학회지
• /
• 제35권2호
• /
• pp.172-179
• /
• 1998

Valve lifter namely tappet is supported by lifter hole which is located upper side of camshaft in cylinder block transforms rotatic mvement of camshaft into linear movement and helps to open and shut the en-gine valve as an engine parts. The face of valve lifter which is continuously contacting with camshaft brings about abnormal wears such as unfair wear and early wear because it is severely loaded in the valve train system. These wears act as a defect like over-clearance and cause imperfect combustion of fuel during the valve lifting in the combustion chamber. Consequently this imperfect combustion makes the engine out-put decrease and has cause on air pollution. To prevent these wears therefore The valve lifter cast in me-tal developed into SiC ceramics valve lifter which has an excellence in wear and impact resistance As a results the optimum process conditions like injection condition mixture ratio and debonding process could be established. After sintering fine-sinered dual microstructure in which prior ${\alpha}$-SiC matches well with new SiC(${\beta}$-SiC) produced by reaction among the ${\alpha}$-SiC carbon and silicon was obtained. Based on the study it is verified that mechanical properties of SiC valve lifter are excellent in Vickers hardness 1100-1200 bending strength (300-350 Pa) fracture toughness(1.5-1.7 Mpa$.$m1/2) Through engine dynamo test-ing SiC valve lifter and metal valve lifter are examined and compared into abnormal phenomena such as early fracture unfair and early wear. It is hoped that this research will serve as an important springboard for the future study of heavy duty diesel engine parts developed by ceramics which has a good wear resis-tance relaibility and lightability.

• 한국세라믹학회지
• /
• 제43권6호
• /
• pp.333-337
• /
• 2006

In this study, the $Sr_{1-x}Ba_{x}Al_{2}O_{4}:Eu^{2+},Dy^{3+}$ phosphor were prepared by the solid-state reaction method and its photoluminescence properties were investigated. Starting powders of $SrCO_3,\;BaCO_3,\;and\;Al_{2}O_3$ were mixed with $Eu_{2}O_3$ as activator, $Dy_{2}O_3$ as co-activator and $B_{2}O_3$ as flux. Then, the mixed powders were heated at the temperature of $1100{\sim}1400^{\circ}C$ for 3 h under the reducing ambient atmosphere of $95%Ar+5%H_2$. The effect of Ba addition from 0.0 to 1.0 mol on photoluminescence was investigated. As the amount of Ba increased, the intensity of emission increased and the optimum long phosphorescence occurred at the amount of 0.1 mol Ba. The optimum sintering condition for long phosphorescent phosphor of $Sr_{1-x}Ba_{x}Al_{2}O_{4}:Eu^{2+},Dy^{3+}$($x=0{\sim}1.0mol$) was found at $1400^{\circ}C$. The excitation spectra showed a broad band of $250{\sim}450nm$ with maximum peak at 360 nm. The maximum peak intensity of emission spectra occurred at the range of $480{\sim}520nm$, depending on Ba content.

• 한국전기전자재료학회논문지
• /
• 제18권1호
• /
• pp.57-61
• /
• 2005

The microwave dielectric properties of 0.6TiTe$_3$O$_{8}$-0.4MgTiO$_3$ ceramics with H$_3$BO$_3$-SnO were investigated to improve the sintering condition for the LTCC. According to the X-ray diffraction patterns, 0.6TiTe$_3$O$_{8}$-0.4MgTiO$_3$ ceramics with H$_3$BO$_3$-SnO had the columbite structure of TiTe$_3$O$_{8}$ phase and the ilmenite structure of MgTiO$_3$ phase and there were no second phase. Increasing the addition of H$_3$BO$_3$-SnO, the density and dielectric constant of the 0.6TiTe$_3$O$_{8}$-0.4MgTiO$_3$ ceramics were increased but the quality factor was decreased. The temperature coefficient of resonant frequency was shifted to the negative(-) direction with addition of H$_3$BO$_3$-SnO.EX>-SnO.

• 한국전기전자재료학회논문지
• /
• 제14권3호
• /
• pp.190-196
• /
• 2001

The microwave dielectric properties and a sintering behavior of MgTiO$_3$-CaTiO$_3$ ceramics doped with Li were investigated. The main composition was fixed as 0.94MMgTiO$_3$-0.06CaTiO$_3$ and Li$_2$CO$_3$was added excessively in the range of 0~10 mol% (with reference to Li atoms) and the specimens were sintered at 1200~140$0^{\circ}C$ for 4 hours. When the amount of Li was small the quality factor and dielectric constant were reduced, while those tow properties increased if the Li amount was above 1 mol%. But if Li was overly added those dielectric properties decreased again. Li, if added in the composition range of 1.0~3.0 mol%, can increase the quality factor of MgTiO$_3$-CaTiO$_3$ ceramics. The optimum amount of Li was 1.5mol% and sinterign condition was 1275$^{\circ}C$/4hr, at which we cudl obtain following results ; dielectric constant ($\varepsilon$$_{r}$) of f20.0, quality factor(Qxf$_{0}$) of 78,000 GHz and temperature coefficient of resonant frequency($\tau$$_{f}$) of -1.6 ppm/$^{\circ}C$.>.>.>.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.183-183
• /
• 2011

Multiferroic materials have been widely studied in recent years, because of their abundant physics and potential applications in the sensors, data storage, and spintronics. $BiFeO_3$ is one of the well-known single-phase multiferroic materials with $ABO_3$ structure and G-type antiferromagnetic behavior below the Neel temperature $T_N$ ~ 643 K, but the ferroelectric behavior below the Curie temperature $T_c$~1,103 K. In this study, the $BiFe_{1-x}Ni_xO_3$ (x=0 and 0.05) bulk ceramics were prepared by solid-state reaction and rapid sintering with high-purity $Bi_2O_32$, $Fe_3O_4$ and NiO powders. The powders of stoichiometric proportions were mixed, as in the previous investigations, and calcined at 450$^{\circ}C$ for $BiFe_{1-x}Ni_xO_3$ for 24 h. The obtained powders were grinded, and pressed into 5-mm-thick disks of 1/2-inch diameter. The disks were directly put into the oven, which has been heated up to 800$^{\circ}C$ and sintered in air for 20 min. The sintered disks were taken out from the oven and cooled to room temperature within several min. The phase of samples was checked at room temperature by powder x-ray diffraction using a Rigaku Miniflex diffractometer with Cu K${\alpha}$ radiation. The Raman measurements were carried out by employing a hand-made Raman spectrometer with 514.5-nm-excitation $Ar^+$ laser source under air ambient condition on a focused area of 1-${\mu}m$ diameter. The field-dependent magnetization measurements were performed with a superconducting quantum-interference-device magnetometer.

• 한국분말재료학회지
• /
• 제20권6호
• /
• pp.467-473
• /
• 2013

This research presents a preparation method of dental components by metal injection molding process (MIM process) using titanium scrap. About $20{\mu}m$ sized spherical titanium powders for MIM process were successfully prepared by a novel dehydrogenation and spheroidization method using in-situ radio frequency thermal plasma treatment. The effects of MIM process parameters on the mechanical and biological properties of dental components were investigated and the optimum condition was obtained. After sintering at $1250^{\circ}C$ for 1 hour in vacuum, the hardness and the tensile strength of MIMed titanium components were 289 Hv and 584 MPa, respectively. Prepared titanium dental components were not cytotoxic and they showed a good cell proliferation property.

• 센서학회지
• /
• 제7권2호
• /
• pp.83-89
• /
• 1998

$TiO_{2-x}$ 박막 습도센서를 스퍼터링법에 의해 제조하고, 스퍼터링 조건과 열처리조건에 따른 습도 감지특성 및 동작온도에 따른 특성 등을 조사하였으며, Auger 전자 분광기와 전자현미경으로 그 원인을 분석하였다. $TiO_{2-x}$ 박막 습도센서는 부임피던스 습도특성을 보였으며, rf power가 200 W, 압력은 50 mTorr 및 기판 온도는 $200^{\circ}C$ 에서 증착하고, $600^{\circ}C$에서 1시간 동안 열처리한 소자의 상대습도 변화에 따른 임피던스 변화는 $0.794\;K{\Omega}/%RH$로 가장 컸으며, 응답 시간은 흡착시 약 2분, 탈착시 약 3분이었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1462-1464
• /
• 1997

The spinel $LiMn_2O_4$ has been synthesized by solid-state reaction. $LiMn_2O_4$ which includes 3 mix $Li_2CO_3$ or $LiNO_3$ and $MnO_2$ prepared by Prelim heating at $350^{\circ}C$ for 24hr. $LiMn_2O_4$ fired at temp range from $600^{\circ}C$ to $800^{\circ}C$ for 48hr. The structure a electrochemical characteristics of spinel $LiMn_2O_2$ wh fabricated by changing sintering condition from st materials are investigated. The spinel $LiMn_2O_4$ prepared by the mixture of L CMD at $800^{\circ}C$ for 48hr showed an initial charge ca of 146mAh/g. The spinel $LiMn_2O_4$ prepared by the m of $LiNO_3$/CMD at $600{\sim}800^{\circ}C$ for 48hr stabilized ch discharge capacity after 50th cycles.

• Journal of Magnetics
• /
• 제13권3호
• /
• pp.110-113
• /
• 2008

In this study, heavy rare earth garnet $Tb_2Bi_1Ga_1Fe_4O_{12}$ powders were fabricated by a sol-gel and vacuum annealing process. The crystal structure was found to be single-phase garnet with a space group of Ia3d. The lattice constant $a_0$ was determined to be 12.465 ${\AA}$. From the analysis of the vibrating sample magnetometer (VSM) hysteresis loop at room temperature, the saturation magnetization and coercivity of the sample are 7.64 emu/g and 229 Oe, respectively. The N$\acute{e}$el temperature($T_N$) was determined to be 525 K. The M$\ddot{o}$ssbauer spectrum of $Tb_2Bi_1Ga_1Fe_4O_{12}$ at room temperature consists of 2 sets of 6 Lorentzians, which is the pattern of single-phase garnet. From the results of the M$\ddot{o}$ssbauer spectrum at room temperature, the absorption area ratios of Fe ions on 24d and 16a sites are 74.7% and 25.3%(approximately 3:1), respectively. These results show that all of the non-magnetic Ga atoms occupy the 16a site by a vacuum annealing process. Absorption area ratios of Fe ions are dependent not only on a sintering condition but also on the temperature of the sample. It can then be interpreted that the Ga ion distribution is dependent on the temperature of the sample. The M$\ddot{o}$ssbauer measurement was carried out in order to investigate the atomic migration in $Tb_2Bi_1Ga_1Fe_4O_{12}$.