• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.280-281
• /
• 2006

Powder grades pre-alloyed with 1.5-3 wt% chromium can be successfully sintered at the conventional temperature $1120^{\circ}C$ although well-monitored sintering atmospheres are required to avoid oxidation. Mechanical properties of the Cr-alloyed PM grades are enhanced by a higher sintering temperature in the range $1120-1250^{\circ}C$, due to positive effects from pore rounding, increased density and more effective oxide reduction. Astaloy CrM (Fe-3 wt% Cr-0.5 wt% Mo) with 0.6 wt% graphite added obtains an ultimate tensile strength of 1470 MPa and an impact strength of 31 J at density $7.1\;g/cm^3$, after sintering at $1250^{\circ}C$ followed by cooling at $2.5^{\circ}C/s$ and tempering.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.696-697
• /
• 2006

This paper presents the densification and microstructure evolution of bilayer components made from 316L stainless steel and M2 High speed steel during co-sintering process. The sintering was carried out at temperatures ranging from $1230-1320^{\circ}C$ in a reducing atmosphere. The addition of boron to 316L was examined in order to increase the densification rate and improve the sintering compatibility between the two layers. It was shown that the mismatch strain bettwen the two layers induces biaxial stresses during sintering, influencing the densification rate. The effect of boron addition was also found to be positive as it improves the bonding between the two layers.

• 한국결정성장학회지
• /
• 제16권2호
• /
• pp.71-75
• /
• 2006

소성 분위기를 변화시켜 골재를 제조할 때 골재의 중앙에 만들어지는 블랙코어(black core) 형성정도의 차이와 골재 물성의 차이점을 알아보기 위해 적점토, 탄소(carbon), 산화철($Fe_2O_3$)이 혼합된 직경 10mm 구형골재를 조성별로 산화분위기, 중성분위기, 환원분위기에서 각각 소성시키고 각각의 비중, 흡수율, 블랙코어 면적비(%)를 측정하고 비교하였다. 산화분위기에서 소성시킨 골재는 껍질(shell)과 블랙코어가 뚜렷하게 구분되는 반면 중성 및 환원분위기에서 소성한 시편에서는 시편의 단면전체에 블랙코어가 형성되었다. 산화분위기와 중성분위기와는 달리 환원분위기에서 소성된 시편에서는 탄소첨가량이 증가할수록 비중이 증가했으며, 전반적인 비중은 가장 낮았다. 흡수율은 모든 분위기에서 탄소첨가량이 증가할수록 증가하는 경향을 보였다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(3)
• /
• pp.231-237
• /
• 1996

Defect equilibrium equations were modelled, and the relations of P $o_2$, venus x were derived using the mass action law. The dominant defect species active in a specified region were determined by fitting the curve of experimental data to the calculated curve of log P $o_2$, versus log x for each theoretical model. The calculated curve for (2:1:2) and (Er')$^{x}$ in the hyperstoichiometric $U_{1-y}$E $r_{y}$ $O_{2＋x}$ and that for (2Er'quot;)$^{x}$ $_{dec}$ in the hypostoichiometric $U_{1-y}$E $r_{y}$ $O_{2－x}$ are in good agreement with the present experimental results. The sintering behavior of Er-doped U $O_2$ is observed with erbium content in oxidizing and reducing atmospheres. For sintering in oxidizing atmosphere, sintered density decreases as increasing y in $U_{1-y}$E $r_{y}$ $O_{2＋x}$. However, in hydrogen atmosphere, sintered density decreases as increasing y at lower erbium content but the density increases again above y=0.10. In oxidizing sintering conditions, the formation of (Er'U')$^{x}$ clusters hinders the diffusion of cations, and hence the sinterability of Er-doped U $O_2$ decreases. In reducing atmosphere of Er-doped U $O_2$ for higher Er concent, the oxygen vacancies make (Er')$^{x}$ cluster decompose by charge compensation and the concentration of mobile cations increases, thereby improving the sinterability.ntration of mobile cations increases, thereby improving the sinterability.ability.

• 한국재료학회지
• /
• 제28권9호
• /
• pp.511-515
• /
• 2018

W-10 wt% Ti alloys that have a homogeneous microstructure are prepared by thermal decomposition of $WO_3-TiH_2$ powder mixtures and spark plasma sintering. The reduction and dehydrogenation behavior of $WO_3$ and $TiH_2$ are analyzed by temperature programmed reduction and a thermogravimetric method, respectively. The X-ray diffraction analysis of the powder mixture, heat-treated in an argon atmosphere, shows W- oxides and $TiO_2$ peaks. Conversely, the powder mixtures heated in a hydrogen atmosphere are composed of W, $WO_2$ and $TiO_2$ phases at $600^{\circ}C$ and W and W-rich ${\beta}$ phases at $800^{\circ}C$. The densified specimen by spark plasma sintering at $1500^{\circ}C$ in a vacuum using hydrogen-reduced $WO_3-TiH_2$ powder mixtures shows a Vickers hardness value of 4.6 GPa and a homogeneous microstructure with pure W, ${\beta}$ and Ti phases. The phase evolution dependent on the atmosphere and temperature is explained by the thermal decomposition and reaction behavior of $WO_3$ and $TiH_2$.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 1993년도 추계학술강연 및 발표대회강연 및 발표논문 초록집
• /
• pp.5-5
• /
• 1993

• 한국세라믹학회지
• /
• 제34권6호
• /
• pp.629-635
• /
• 1997

The effects of the annealing atmospheres(O2, N2) and sintering additives that Bi2O3 is a major composition on the microwave dielectric and sintering propertie of (1-x)CaTiO3-xLaAlO3 system were investigated. The annealing atmospheres and the increase of annealing time after sintering did not affect the relative dielectric constant($\varepsilon$r) and temperature coefficient of resonant frequency($\tau$f) of (1-x)CaTiO3-xLaAlO3 system. However, the Q.f0 values of (1-x)CaTiO3-xLaAlO3 were very sensitive to annealing atmospheres. As the annealing time increased under O2 atmosphere the Q.f0 values of (1-x)CaTiO3-xLaAlO3 enhanced untill 10 hrs in 0.3$\leq$x$\leq$0.6 region, but degraded over that time. The increasing rate of Q.f0 value increased wth increasing x. On the other hand, as the annealing time increased under N2 atmosphere the Q.f0 values were constant in x$\leq$0.6 region, increased gradually in x$\geq$0.7 region. When 0.97Bi2O3-0.03Al2O3 and 0.76Bi2O3-0.24NiO of 3wt% as sintering additives were added to (Ca0.5La0.5) (Ti0.5Al0.5)O3 (x=0.5) the sintering temperature of 1$600^{\circ}C$ was lowered to 140$0^{\circ}C$, and the relative dielectric constant($\varepsilon$r) and temperature coefficient of resonant frequency($\tau$f) were not nearly changed. The addition of 0.97Bi2O3-0.03Al2O3 and 0.76Bi2O3-0.24NiO of 3wt% to (Ca0.5La0.5)(Ti0.5Al0.5)O3 made the Q.f0 values to be lower about 15% and 34%, respectively.

• 한국세라믹학회지
• /
• 제32권12호
• /
• pp.1337-1348
• /
• 1995

TZP/SUS- and ZT/SUS-functionally gradient materials (FGM) were fabricated by pressureless sintering in Ar-atmosphere. The sintering defects such as warping, frustrum formation, splitting and cracking which originated from shrinkage and sintering behaviors of metal and ceramics different from each other could be controlled by the adjustment with respect to the particle size and phase type of zirconia. The residual stresses generated on the metal and ceramic regions in FGM were characterized with X-ray diffraction method, and relaxed as the thickness and number of compositional gradient layer were increased. The residual stress states in TZP/SUS-FGM have irregular patterns by means of the different sintering behavior and cracking at ceramic-monolith. While in ZT/SUS-FGM, compressive stress is induced on ceramic-monolith by the volume expansion of monoclinic ZrO2 at phase transformation. Also, compressive stress is induced on metal-monolith by the constraint of warping which may be created to the metal direction by the difference of coefficient of thermal expansions. As a consequence, it has been verified that the residual stress generated on FGM is dominantly influenced by the thickness and number of compositional gradient layer, and the sintering defects and residual stress can be controlled by the constraint of the difference of shrinkage and sintering behaviors of each component.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 춘계학술대회 논문집
• /
• pp.78-79
• /
• 2009

We have investigated low temperature sintering characteristics of organic Ag complex. Organic Ag complex was coated on the glass substrate by spin coating method. The coated Ag complex was sintered in an air atmosphere. The sintering temperature was varied from 30 to $80^{\circ}C$ and sintering time was varied from 1 to 228 hour. The sheet resistance was abruptly changed at $80^{\circ}C$-6h, $65^{\circ}C$-24h, $30^{\circ}C$-228 hour and the thickness of the coated film was significantly decreased. The sheet resistance of Ag films were about $0.53\;{\Omega}/{\square}$ at the $80^{\circ}C$ - 12hour.

• 한국분말재료학회지
• /
• 제9권6호
• /
• pp.416-421
• /
• 2002

Elemental powders are used in high energy milling processes for the synthesis of new compounds. The low temperature solid state reactions during milling in inert gas atmosphere may result in intermetallic phases, carbides, nitrides or silicides with a nanocrystalline structure. To obtain dense materials from the powders a pressure assisted densification is necessary. On the other side the defect-rich microstructure can be used for activated sintering of elemental powder mixtures to obtain dense bodies by pressureless sintering. Results are discussed for nanocrystalline cermet systems and for the sintering of aluminides and silicides.