• Journal of Electrical Engineering and Technology
• /
• 제3권1호
• /
• pp.94-100
• /
• 2008

This paper presents a new control method of single-phase active power filter (APF) for the compensation of harmonic current components in nonlinear loads. To facilitate the possibility of complex calculation for harmonic current detection of the single phase, a single-phase system that has two phases was constructed by including an imaginary second-phase giving time delay to the load current. The imaginary phase, which lagged the load current T/4 (Here T is the fundamental cycle) is used in the conventional method. But in this proposed method, the new signal as the second phase is delayed by the filter. Because this control method is applied to a single-phase system, an instantaneous calculation was developed by using the rotating reference frames synchronized to source-frequency rather than by applying instantaneous reactive power theory that uses the conventional fixed reference frames. The control scheme of single-phase APF for the current source with R-L loads is applied to a laboratory prototype to verify the proposed control method.

• 전력전자학회논문지
• /
• 제22권6호
• /
• pp.496-503
• /
• 2017

This study proposes a high-performance current control algorithm for a diode-bridge-type single-phase boost power factor correction (PFC) converter. The conventional asynchronous single-phase current controllers that directly control AC-type current tend to be accompanied by steady-state errors due to their poor dynamic characteristics for the transient-state, which can be attributed to bandwidth limitations and phase delays. In the proposed algorithm, an ideal current control with minimal phase delays and steady-state errors can be achieved by using a virtual DQ synchronous reference frame and by controlling the synchronous reference frame excluding the frequency component in the single-phase system. The performance of the conventional asynchronous single-phase current controller is compared with that of the proposed algorithm through simulation and experiments, and the results have confirmed the superiority of the latter.

• 전력전자학회논문지
• /
• 제25권1호
• /
• pp.54-60
• /
• 2020

A digital current control scheme using virtual d-q transformation for a boost single-phase power factor correction (PFC) converter is proposed. The use of virtual d-q transformation in single-phase power converters is known to improve current control performance. However, the conventional virtual d-q transformation-based digital current control scheme cannot be directly applied to the boost single-phase PFC converter because the current and average voltage waveforms of the inductor used in the converter are not sinusoidal. To cope with this problem, this study proposes a virtual sinusoidal signal generation method that converts the current and average voltage waveform of the inductor into a sinusoidal waveform synchronized with the grid. Simulation and experimental results are provided to show that the virtual d-q transformation-based digital current control is successfully applied to the boost single-phase PFC converter with the aid of the proposed virtual sinusoidal signal generation method.

• 전력전자학회논문지
• /
• 제17권1호
• /
• pp.1-7
• /
• 2012

This paper describes the performance comparison results for current controller of a single-phase PFC converter with 1-switch voltage doubler strategy for single-phase double-conversion UPS(Uninterruptible Power Supply). A single-phase PFC converter with 1-switch voltage doubler strategy needs a diode bridge and one bidirectional active switch. Thus it is possible to reduce the material cost. However, the study results of current controller design and comparison of current control method has not been known after the converter circuit was proposed. For the performance comparison of current control, single-phase 3 kVA double-conversion UPS was tested. The performance of PI and PR current controller is experimentally confirmed with followings - input current reference tracking, input power factor correction and input current THD suppression.

• Journal of Electrical Engineering and Technology
• /
• 제13권6호
• /
• pp.2354-2363
• /
• 2018

This paper proposed a novel double closed control strategy for single-phase voltage source pulse width modulation (PWM) rectifier based on active disturbance rejection control (ADRC) and dq current decoupling control. First, the mathematical model of the single-phase PWM rectifier in the d-q axis synchronous rotating reference frame is established by constructing a virtual component using a second-order generalized integrator (SOGI). Then, the mathematical model is simplified according to the active power conservation, and the first-order equation of single-phase PWM rectifier voltage outer loop is acquired. A linear auto-disturbance rejection controller is used to design the voltage outer loop according to the first-order equation. Finally, the proposed control strategy and the traditional PI control are compared and verified by simulation and physical experiments. Both simulation and experimental results confirm that the proposed control strategy has excellent dynamic performance and strong rejection ability to disturbances.

• 전기전자학회논문지
• /
• 제24권4호
• /
• pp.954-960
• /
• 2020

본 논문은 단상 영구자석 동기전동기의 속도 가변형 비례공진 전류제어 기법을 제안한다. 단상 영구자석 동기전동기는 전자기적 특성상 고정자 전류와 역기전력의 위상차에 따른 부토크 및 영토크가 발생하며 센서리스 운전 시 낮은 고정자 저항과 인덕턴스로 인해 과전류 제한이 필요하다. 이러한 조건하에서 전류제어를 위해 3상 교류 전동기에 사용되는 벡터 제어를 이용할 경우, 좌표변환, 역좌표변환 및 가상의 dq축 성분을 생성하는 과정이 필요하다. 하지만, 단상 영구자석 동기전동기의 자기적 특성을 고려하여 제안한 속도 가변형 비례공진 전류제어 기법은 3상 교류 전동기에 사용되는 좌표변환 과정이 필요하지 않다. 본 논문에서는 가변 비례공진 전류제어 기법을 이용하여 안정적인 기동 성능을 확인하며 일정 속도 도달 시 위치 센서 없이 단상 영구자석 동기전동기의 수학적 모델 기반 센서리스 제어로 제안한 전류제어 기법의 효용성을 다수의 실험을 통해 검증하였다.

• 전력전자학회논문지
• /
• 제21권2호
• /
• pp.144-149
• /
• 2016

This paper presents a power control method of high-speed single-phase BLDC motor. Most electric appliances require a power factor corrector (PFC) to mitigate grid current harmonics. However, the reactive components and power semiconductors in the PFC increase system cost and dimension. In this paper, a new motor drive system for a high-speed single-phase BLDC motor is proposed, which can decrease grid current harmonics without PFC by directly manipulating motor power and eliminating bulky electrolytic dc-link capacitor. Given that the proposed motor power control method does not require motor current controller, no current sensor is necessary. Moreover, the proposed algorithms can be easily implemented using a low-cost micro-controller. The effectiveness of the proposed power control method is verified by experiments.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.489-492
• /
• 1999

This paper proposes a control method for three-phase voltage-source PWM converters using only a single current sensor in the DC link. A predictive current controller for the voltage-source PWM converter is used so that all phase currents can be reconstructed in a switching period although one or two of active vectors are applied only for a short time. Compensation of the 2 step delays is also included. In this paper single sensor current control using predictive state observer will be discussed, and investigated experimentally.

• Journal of Electrical Engineering and Technology
• /
• 제9권3호
• /
• pp.899-907
• /
• 2014

This paper deals with fault-tolerant control of five-phase induction motor (IM) drives under single-phase open. By exploiting a decoupled model for five-phase IM under fault, the indirect field-oriented control ensures that electromagnetic torque oscillations are reduced by particular magnitude ratio currents. The control techniques are developed by the third harmonic current injection, in order to improve electromagnetic torque density. Furthermore, Proportional Resonant (PR) regulator is adopted to realize excellent current tracking performance in the phase frame, compared with Proportional Integral (PI) and hysteresis regulators. The analysis and experimental results confirm the validity of fault-tolerant control under single-phase open.

• 조명전기설비학회논문지
• /
• 제21권8호
• /
• pp.44-53
• /
• 2007

단상유도전동기의 기동전류를 줄이기 위하여 슬라이딩모드 제어기가 적용된다. 단상유도전동기의 기동전류가 정격치 이하로 유지되도록 슬라이딩모드 제어기의 스위칭 기능을 조절함으로써 전동기 입력전압이 제어되며 또한 속도도 제어된다. 슬라이딩 모드 제어기의 스위칭은 속도 오차 신호와 속도 변화량에 대하여 적절이 수행된다. 단상 유도 전동기의 기동특성이 슬라이딩 제어기를 사용하여 크게 향상될 수 있음을 보여 준다.