• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2073-2075
• /
• 2004

본 논문에서는 nonradiative dielcctric (NRD) 도파로를 이용하여 28GHz대에서의 single balanced mixer를 설계하였다. 혼합기에 필요한 $90^{\circ}$ hybrid direction기 3dB 결합기를 NRD 도파로를 이용하여 설계 하였고 CST MWS를 이용하여 설계 결과를 검중 하였으며 결과는 중심 주파수 28GHz에서 대역폭이 1GHz의 결합기를 설계하였음을 확인할 수 있었다. 이와동시에 다이오드를 부착하기 위해 NRD 도파로와 마이크로스트립의 매칭 구조를 1 pole UDR과 patch를 이용하여 혼합기를 설계, 제작하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.3
• /
• pp.339-345
• /
• 2001

In this paper, FG-CPW (Finite-Ground Coplanar Wave-Guide) balanced diode mixer is presented. Frequency bandwidth is selected for a C-band, which is 5.72~5.82 GHz for RF, 5.58~5.68 GHz for LO, and 140 MHz for IF signals. A rat-race hybrid is designed for the accomplishment of single balanced type. A low pass filter (LPF) with CPW structure is used far good conversion loss and unwanted harmonics suppression. When LO signal with the power of 4 dBm at 5.635 GHz is injected, a conversion loss of 6.2 dB is obtained for the mixer. Also, the LO to RF and LO to IF isolation of 30 dB and 40 dB are obtained, respectively. This mixer can be used in the area on wireless LAN application.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.90-98
• /
• 1999

This paper presents a wideband single-balanced mixer using a diode which can be used in RF receiver of microwave measurement systems. For wideband characteristic, local oscillator(LO) signal is provided to diode with low loss using a coplanar waveguide-to-slotline balun. For high isolation characteristic radio frequency (RF) port and intermediate frequency (IF) port are designed using directional coupler. This mixer presents 30.5~31.17dB conversion loss whose flatness is within 1dB for 9 kHz~2.6 GHz wideband RF signal, and above 30 dB isolation for LO signal.

• Journal of electromagnetic engineering and science
• /
• v.3 no.1
• /
• pp.1-6
• /
• 2003

In this paper, a sub-harmonic dual-gate FET mixer is suggested to improve the isolation characteristic between LO and RF ports of an unbalanced mixer. The mixer was designed by using single-gate FET cascode structure and driven by the second harmonic component of LO signal. A dual-gate FET mixer has good isolation characteristic since RF and LO signals are injected into gatel and gate2, respectively. In addition, the isolation characteristic of a sub-harmonic mixer is better than that of a fundamental mixer due to the large frequency separation between the LO and RF frequencies. As RF power was -30 ㏈m and LO power was 0 ㏈m, the designed mixer yielded the -47.17 ㏈m LO-to-RF leakage power level, 10 ㏈ conversion gain, -2.5 ㏈m OIP3, -12.5 ㏈m IIP3 and -1 ㏈m 1 ㏈ gain compression point. Since the LO-to-RF leakage power level of the designed mixer is as good as that of a double-balanced mixer, the sub-harmonic dual-gate FET mixer can be utilized instead.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.4 no.3 s.8
• /
• pp.45-50
• /
• 2005

In this paper, a broadband single balanced mixer is presented using a wideband rat-race implementation by vertical coupling. Frequency is selected as $1.5{\sim}3$ GHz for RF, $1.64{\sim}3.14$ GHz for LO, and 140 MHz for IF signals. When LO signal with 6 dBm at 2.7 GHz is injected, a conversion loss of 7.5 dB and RF to LO isolation of 30 dB are obtained. Also, an average conversion loss of 10 dB, RF to LO isolation of 30 dB, and LO to IF isolation of 45 dB are obtained for frequency band of $1.5{\sim}3$ GHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.2
• /
• pp.239-244
• /
• 2004

In this paper, we have developed a frequency mixer which can be used as a microwave phase conjugator in the LS band retrodirective antenna system. The mixer as a phase conjugator must have an If signal of which frequency is nearly as high as that of an RF signal, so this fact brings difficulty in the combination of input signals and the design of impedance matching circuit. The circuit configuration is chosen to be of the gate mixer using a pseudomorphic HEMT device. The operating frequencies are 4.00 ㎓, 2.01 ㎓, and 1.99 ㎓ for LO, RF, and IF, respectively. Conversion gain is measured to be 12.5 ㏈ and 1 ㏈ compression point -34 ㏈m at the LO power of -7 ㏈m. The mixer fabricated in this research is the single-ended type, where RF leakage signal appears inevitably at the If port because RF and If frequencies are almost the same. The circuit topology suggested here can be applied directly to the design of balanced-type mixers and phase conjugators.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.6
• /
• pp.34-40
• /
• 2011

From the present paper researched about the Design of Image Rejection SSB Modulator for X-Band Monopulse RADAR using Waveguide Hybrid Coupler. Generally, SSB modulator mixes IF(RF) and LO signals, and then it converts to RF(IF) frequency band. In this case, in order to transmit one sideband from RF band, SSB modulator is demanded the removal of image and LO signal. The balanced mixer was designed using waveguide hybrid coupler and crystal mixer diode to mix LO and IF signal. And also the IF Amplifier was designed for IF(+) and IF(-) signal generation which have $90^{\circ}$ phase differences which are suitable in two crystal mixer diode inputs. In order to maintain a high electric reliability from high frequency band the waveguide and IF amplifier's case were manufactured with aluminum using deep brazing techniques. The test result of SSB modulator, LO and sideband signal rejection ratio were 14.2dB and 18.5dB respectively.

• 한국ITS학회:학술대회논문집
• /
• 2005.11a
• /
• pp.241-244
• /
• 2005

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.7 s.98
• /
• pp.753-759
• /
• 2005

In this paper, we have developed a new type of single balanced mixer with the RF MEMS $180^{\circ}$ hybrid coupler using surface micromachining technology. The $180^{\circ}$ hybrid coupler in this mixer is composed of the dielectric-supported air gapped microstriplines(DAMLs) which have signal line with $10{\mu}m$ height to reduce substrate dielectric loss and dielectric posts with size of $20{\mu}m{\times}20{\mu}m$ to elevate the signal line on air with stability At LO power of 7.2 dBm, the conversion loss was 15.5 dB f3r RF frequency or 57 GHz and RF power of -15 dBm. Also, we obtained the good RF to LO isolation of -40 dB at LO frequency of 58 GHz and LO power of 7.2 dBm. The main advantage of this type of mixer is that we are able to reduce the size of the chips due to integrating the MEMS passive components.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.37-43
• /
• 2007

In this.paper, we introduce design and implementation results of the single balanced diode mixer for European point-to-point microwave radio in order to improve flatness performance. When a resonator such as RF filter is integrated with a mixer, impedance characteristic of 50 ohm is maintained only in RF band, not in LO band resulting deterioration of flatness performance because of LO power variation on the diode. In the paper, we suggest a design method of mixer integrated with image rejection filter and LO harmonic filter to have a better performance of flatness using embedding electrical length between filter and mixer's port. Frequency specification of fabricated mixer is $21.2{\sim}22.6\;GHz$ for RF, $19.32{\sim}20.72\;GHz$ for LO and 1.88 GHz+/-50 MHz for IF, respectively. Measured results show conversion loss of 8.5 dB, flatness of 2 dB, input PldB of 8 dBm, IIP3 of 15 dBm under LO power level of 10 dBm. Return losses of RF, LO and IF port are under -12 dB, -10 dB and -5 dB, respectively. Isolations of LO/RF and LO/IF are 20 dB and 50 dB, respectively.