• Korean Journal of Materials Research
• /
• v.18 no.10
• /
• pp.558-563
• /
• 2008

TiAlN films were deposited on WC-5Co substrates with different buffer layers by D.C. magnetron sputtering. The films were evaluated by microstructural observations and measuring of preferred orientation, hardness value, and adhesion force. As a process variable, various buffer layers were used such as TiAlN single layer, TiAlN/TiAl, TiAlN/TiN and TiAlN/CrN. TiAlN coating layer showed columnar structures which grew up at a right angle to the substrates. The thickness of the TiAlN coating layer was about $1.8{\mu}m$, which was formed for 200 minutes at $300^{\circ}$. XRD analysis showed that the preferred orientation of TiAlN layer with TiN buffer layer was (111) and (200), and the specimens of TiAlN/TiAl, TiAlN/CrN, TiAlN single layer have preferred orientation of (111), respectively. TiAlN single layer and TiAlN/TiAl showed good adhesion properties, showing an over 80N adhesion force, while TiAlN/TiN film showed approximately 13N and the TiAlN/CrN was the worst case, in which the layer was destroyed because of high internal residual stress. The value of micro vickers hardness of the TiAlN single layer, TiAlN/TiAl and TiAlN/TiN layers were 2711, 2548 and 2461 Hv, respectively.

• Journal of the Korean Society for Heat Treatment
• /
• v.28 no.6
• /
• pp.291-295
• /
• 2015

IGZO single layer and $IGZO/TiO_2$ bi-layered films were deposited on glass substrate at room temperature with radio frequency magnetron sputtering to investigate the effect of $TiO_2$ buffer layer on the electrical and optical properties of the films. For all deposition, the thickness of IGZO and $TiO_2$ Buffer layer was kept at 100 and 5 nm, respectively. In a comparison of figure of merit, IGZO films with a 5-nm-thick $TiO_2$ buffer layer show the higher figure of merit ($8.40{\times}10^{-5}{\Omega}^{-1}$) than that of the IGZO single layer films ($6.23{\times}10^{-5}{\Omega}^{-1}$) due to the enhanced optical transmittance and the decreased sheet resistance of the films. The observed results mean that a 5 nm thick $TiO_2$ buffer layer in the $IGZO/TiO_2$ films results in better electrical and optical performance than conventional IGZO single layer films.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.7
• /
• pp.1387-1393
• /
• 2007

Even if the linearly separable patterns can be classified by the conventional single layer perceptron, the non-linear problems such as XOR can not be classified by it. A fuzzy single layer perceptron can solve the conventional XOR problems by applying fuzzy membership functions. However, in the fuzzy single layer perception, there are a couple disadvantages which are a decision boundary is sometimes vibrating and a convergence may be extremely lowered according to the scopes of the initial values and learning rates. In this paper, for these reasons, we proposed an enhanced fuzzy single layer perceptron algorithm that can prevent from vibration the decision boundary by introducing a bias term and can also reduce the learn time by applying the modified delta rule which include the learning rates and the momentum concept and applying the new linear activation function. Consequently, the simulation results of the XOR and pattern classification problems presented that the proposed method provided the shorter learning time and better convergence than the conventional fuzzy single layer perceptron.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.29 no.3
• /
• pp.125-132
• /
• 2011

Is very simple in tension work of screen mesh for effective printing if worker uses screen mesh of player who desire at screen print process. General method is methods that use mesh of player who want on screen frame as screen plate because tensioned. The single layer screen plate was made from one sheet screen mesh and the double layer screen plate was made from two sheets screen mesh overlapped. The thickness of sensitive emulsion applied to double layer screen plate is more thicker than two time s of thickness of emulsion applied to single layer screen plate. It seems that the sensitive emulsion inserted between an upper layer and a lower layer of double layer screen mesh.

• Progress in Superconductivity and Cryogenics
• /
• v.13 no.1
• /
• pp.1-5
• /
• 2011

[ $CeO_2$ ]has been widely used for single buffer layer of coated conductor because of superior chemical and structural compatibility with $ReBa_2Cu_3O_{7-{\delta}}$(Re=Y, Nd, Sm, Gd, Dy, Ho, etc.). But, the surface of $CeO_2$ layer showed cracks because of the large difference in thermal expansion coefficient between metal substrate and deposited $CeO_2$ layer, when thickness of $CeO_2$ layer exceeds 100 nm on the biaxially textured Ni-3%W substrate. The deposition rate has been limited to be less than 6 $\AA$/sec in order to get a good epitaxy. In this research, we deposited $CeO_2$ single buffer layers on biaxially textured Ni-3%W substrate with 2-step process such as thin nucleation layer(>10 nm) with low deposition rate(3 $\AA$/sec) and thick homo epitaxial layer(>240 nm) with high deposition rate(30 $\AA$/sec). Effect of deposition temperature on degree of texture development was tested. Thick homo epitaxial $CeO_2$ layer with good texture without crack was obtained at $600^{\circ}C$, which has ${\Delta}{\phi}$ value of $6.2^{\circ}$, ${\Delta}{\omega}$ value of $4.3^{\circ}$ and average surface roughness(Ra) of 7.2 nm within $10{\mu}m{\times}10{\mu}m$ area. This result shows the possibility of preparing advanced Ni substrate with simplified architecture of single $CeO_2$ layer for low cost coated conductor.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.10 no.1
• /
• pp.47-54
• /
• 2004

Normally, the single wall(SW) corrugated board has more advantages than double wall (DW) corrugated board in terms of the cost of the materials and logistics. For instance, the SW corrugated board has 3 layer papers whereas the DW corrugated board has 5 layer papers. The thickness of the SW is about 5mm, but that of the DW is 8mm. Accordingly, the SW corrugated board is quite more used in the developed countries than the DW corrugated board. But in Korea, the DW corrugated board is quite more used. The reason why more DW corrugated board are used than the SW corrugated in Korea is that in order that the SW corrugated board has the same box compression strength as DW corrugated board, the cost of the SW corrugated board is higher than that of the DW corrugated board because the virgin kraft liners are all imported from overseas. In this study, the physical properties such as flat crush strength and column crush strength of typical SW corrugated board and single wall dual-layer medium corrugated board and their costs were analyzed. The analysis resulted in that single wall dual-layer medium corrugated board has the same thickness as the SW corrugated board but the more flat crush strength and column crush strength and the less cost than the SW corrugated board.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.277-280
• /
• 2008

Multi layer bellows are being manufactured for commercial vehicle because of the characteristic of high durability compared with single iaγor bellows used to passenger vehicle. Finite Element Method (FEM) study and optimization about single layer bellows are actively progressed, but FEM study about multi layer bellows which have gap between layer is rarely processed. Therefore, this article presents finite element modeling of multi layer bellows for the improvement of simulation reliability. For the shape optimization of multi layer bellows, design of experiment and Taguchi method are used.

• Fashion & Textile Research Journal
• /
• v.11 no.2
• /
• pp.359-362
• /
• 2009

This study investigates the behavior of water vapor permeability of a layered system to find out a comfortable combination of a layered system for outdoor activities and examines the water vapor permeability of various types of outdoor clothing fabrics. The layered system includes the base layer such as sportswool and polyester/cotton fabrics, the middle layer such as single and double sided fleece fabrics, and the shell layer such as polyurethane-coated, PTFE-laminated and microfiber fabrics in this experiment. Results show that the layered system was applied, it was working together as a whole having some influence on each other layer, though every layer offered varying degree of water vapor permeability. Water vapor permeability of layered system exactly followed the same trend as the shell layer, which is all vapor permeable water repellent fabrics as a single layer. The rate of water vapor transfer through a layered system is mainly related to the type of vapor permeable water repellent fabrics used for the shell layer.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.777-778
• /
• 2006

This paper deals with the optimum rotor design approach about the multi-layer design of the buried magnets in an Interior Permanent Magnet Synchronous Motor (IPMSM), on the efficiency improvement by using Response Surface Methodology (RSM). In the multi-layer design of the prototype 15kw IPMSM, the constant amount of buried PM is split from the single-layer into double-layer design for improving the efficiency characteristics. The optimum double-layer rotor structure is built with the help of RSM analysis. The improvement of IPMSM efficiency is verified by the Finite Element Method (FEM) results comparison with the prototype single-layer IPMSM.

• Journal of Information Display
• /
• v.2 no.4
• /
• pp.8-14
• /
• 2001

Three types of conjugated polymers, poly(PZ-Pi), poly(PZ-BPI) and poly(PZ-NPI) were synthesized by Schiff-base reaction. These new conjugated polymers exhibited improved solubility in common organic solvents due to the presence of alkyl side chains as well as azomethine groups, Double layer LEDs made with the synthesized polymers as emitting layer and $Alq_3$, as electron transporting layer exhibited enhanced EL emission and efficiency compared to those of single layer LEDs. Double layer LEDs exhibited gradual shift in the emission peak th the single layer LED, made of only $Alq_3$ as the emitting layer as the thickness of $Alq_3$ layer increased.