• Journal of Electrochemical Science and Technology
• /
• v.10 no.3
• /
• pp.271-275
• /
• 2019

Anodic $TiO_2$ nanotubes were simultaneously grown and doped with $RuO_2$ by single-step anodization in a negatively-charged $RuO_4{^-}$ precursor. Subsequently, a high positive voltage was imposed on the nanotubes in an $F^-$-based electrolyte (a process referred to as potential shock), which led to the formation of a through-hole $RuO_2$-doped $TiO_2$ nanotube membrane without significant loss of the $RuO_2$ catalyst. XPS results confirmed that the doped Ru metal was converted into $RuO_2$ as the potential shock voltage increased. Further increases in the potential shock voltage led to the formation of $RuO_x/Ru$ in the $TiO_2$ nanotubes. All of our results clearly showed that a through-hole catalyst-doped $TiO_2$ nanotube membrane can be produced by a sequence consisting of single-step anodization and the potential shock process.

• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.3
• /
• pp.375-382
• /
• 1999

The purpose of this article is to present the clinical and laboratory procedures for single tooth restoration using 'Combination Implant Crown'. It is cemented on implant abutment and that abutment is screw-retained over implant body. This type of implant restorations has the advantages of cement-retained restoration while being antirotational and retrievable. And, more esthetic and functional result can be achieved by minimizing the size of access hole. The results were as follows : 1. Preparation of abutment below the cuff line should be avoided 2. Axial reduction of implant abutment should not be excessive because it may weaken the abutment 3. More esthetical and functional occlusal surface was achieved with a minimal access hole which is slightly larger than the diameter of hex driver to enable future total retrievability. 4. Combination Implant Crown has the advantages of both the cement-retained and screw-retained type implant restoration. 5. Cementation between implant crown and abutment reduces screw loosening through even force distribution

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.195-197
• /
• 2006

The present study examined the characteristics of high speed welding thin metal sheet using single mode fiber laser of averaged maximum output power 300 W. Due to the fiber laser that has a good quality of beam can make a very small focusing beam size, thin metal sheet welding and high speed key hole welding can be peformed by high power density.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.6
• /
• pp.563-575
• /
• 2007

This contribution contained the classical work of an open-hole tensile plate to demonstrate the performance of grating shearography and to compare with the results obtained by other full-field measurement techniques, The isotropic plate with an open-hole has often appeared in the previous contributions introducing novel full-field method and system. Grating shearography directly provided six quantitative measurands about the specimen's surface kinematics by using a single measurement set: three in-plane strains, in plane rotation, and two out-of-plane slopes. The quasi-plane wavefront of grating metrology led to high signal-to-noise ratio (SNR) and thus neither fitting nor filtering was applied, and the small shearing distance of $101{\mu}m$ could be used. The small shearing distance provided the outstanding spatial resolution of $80{\mu}m$ and sensitivity appropriate for experimental mechanics. Finally, the grating shearography enabled the visualization of the complex surface deformation around the hole and also detected parasitic flexions of the specimen in the micrometer regime during the tensile test.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.3
• /
• pp.38-44
• /
• 2017

The technology of electrical discharge tap machining may be appropriate for making thread out of highly brittle material. Especially, it is very difficult to machine tap with the traditional method if the brittle material has been hardened by quenching. In this study, the shape of electrical discharge blind hole tap machining was analyzed by discharge time, discharge current, and the flushing hole condition after quenched the tool steel of STD11 has discharged the tap shape with a screw-shaped copper(Cu) electrode. An experimental design was planned and analyzed by Taguchi robust experimental design. The result showed that the shape of the blind hole discharge tap was influenced by the flushing hole, discharge time, and discharge current. The most important factor of the processing conditions was found to be the discharge current. When blind hole EDM with a copper electrode with a flushing hole was conducted, the discharged shape was found to be smooth and the angle of the discharged tapped thread was also found to be close to the thread angle of $60^{\circ}$. As the values of discharge time and discharge current increased, the EDMed surface coarsened due to the increase of the single discharge energy and the shape of the thread collapsing.

• Journal of Ocean Engineering and Technology
• /
• v.8 no.1
• /
• pp.131-143
• /
• 1994

The BTA(boring and trepanning association) deep hole machining has an increasing demands because of its wide applications and its good productivity. The main feature of the BTA tools is that the tool cutting edges are unsymmetrically located on the boring head. This provides a stabilizing cutting force resultant necessary for self guidance of the boring head. The BTA tools are capable of machining for having a large length to diameter ratio in single pass. A study of the accuracy and surface finish of holes produced would reveal quite useful information regarding the process. This study deals with the experimental results obtained during BTA machining on SM55C, SM45C steel under differnt machining conditions.

• The Bulletin of The Korean Astronomical Society
• /
• v.42 no.1
• /
• pp.43.1-43.1
• /
• 2017

We investigate properties of black hole (BH) binaries formed in globular clusters, by using direct N-body simulations. Comparing with previous studies which usually considered single BH masses, our models consist of two-component BH masses, or continuous BH mass function with single mass ordinary cluster stars. During the early stage of dynamical evolution, initially distributed BHs are move to the cluster center by dynamical friction, then BH-BH binaries start to be formed, and eventually be ejected from the cluster due to three body interaction. Finally we find the formation efficiency of high mass BHs are alwats larger than that of lower mass BHs, implying that a BH mass spectrum expected from GW observation should be biased to high mass. In addition, mass ratios of BHs in binaries prefer similar masses (ratio~1), while the most extreme case is less than 3. Expected merger rate from our models is about 7 BH-BH mergers per $Mpc^3$ per yr.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2007.06a
• /
• pp.87-92
• /
• 2007

This work describes the installation and preliminary measurements of an electrical resistivity tomography (ERT) system to monitor the injection of recycled water into a confined aquifer in the area of Sindos (Thessaloniki N. Greece). The aim is to provide, through time-lapse ERT measurements and processing, geoelectrical images of rather increased volumetric sampling around and between the holes and to obtain improved understanding of the flow and transport of the injected water. The details about the general setting, the construction and installation of the ERT cables into the boreholes are explained in full. Preliminary measurements involving single and cross-hole ERT measurements were obtained and processed with a 2D inversion algorithm to produce images of the subsurface. Results depict a very good correlation between ERT images and the lithology and resistivity logs; an indication of the reliability of the approach.

• Current Optics and Photonics
• /
• v.6 no.2
• /
• pp.129-136
• /
• 2022

We propose a photonic crystal fiber (PCF) with a slotted porous core and elliptical-hole cladding, for high birefringence in the terahertz regime. Asymmetry in the guided mode is obtained mainly by using arrays of elliptical air holes in the TOPAS^® polymer cladding. We investigate the tradeoff between several structural parameters and find optimized values that can have a high birefringence while satisfying the single-mode condition. The optical properties in the terahertz regime are thoroughly analyzed in numerical simulations, using a full-vector finite-element method with the perfectly-matched-layer condition. In an optimal design, the proposed photonic crystal fiber shows a high birefringence of 8.80 × 10^-2 and an effective material loss of 0.07 cm^-1 at a frequency of 1 THz, satisfying the single-mode-guidance condition at the same time. The proposed PCF would be useful for various polarization-management applications in the terahertz range.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.342-345
• /
• 2009

Bright light-emitting single crystal organic field-effect transistors (FETs) based on highly luminescent oligo(p-phenylenevinylene) (OPV) derivatives are demonstrated. Although OPV single crystal FETs show both p - and n - type FET operation, we found that an increase in the conjugation length of the OPV derivatives from three phenylene rings to five phenylene rings results in an improvement in the electron mobility by an order of magnitude, while retaining the high hole mobility with intense electroluminescence.