• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.801-806
• /
• 2000

This experimental study is to investigate the intermittent spray characteristics of a multi-hole nozzle in a heavy-duty DI diesel engine. Multi 8 hole$(d_n=0.25mm)$, Multi 3 hole$(d_n=0.42)$ and Sing hole nozzle$(d_n=0.25mm)$ were used in this experiment. By using the 2-D PDPA(phase Doppler particle analyzer), the droplet diameter and the velocity of a diesel spray injected intermittently from the multi and the single-hole nozzle into a still ambient were measured. In order to calculate the mean values such as mean velocity, SMD, AMD etc. and to analyze the intermittent characteristics, the time-window of 0.15ms were applied. In the spray, the small droplet$(D<10{\mu}m)$ was regarded as an air flow, and the correlation between the fuel droplet$(10{\mu}m and the air (low was examined. The normalized axial droplet-air relative velocity of the 8 hole, the 3 hole and the single hole nozzle was evaluated as 0.081, 0.067, 0.06 and in case of the radial droplet-air relative velocity, the normalized. value is 0.014, 0.013 and 0.008 respectively.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.41 no.3
• /
• pp.207-212
• /
• 2005

Dual frequency acoustic pinger(AP) was manufactured to reduce study effect by long-term use of developed single frequency AP to prevent cetacean bycatch. Directivity characteristic of transducer was the omnidirectional pattern which showed less than ${\pm}3dB$ the change range of sensitivity on the beam pattern of right and left. Source power level(SPL) was 1384311pa with epoxy window before casing however after casing 1170B11Pa at sea. Dual frequency Af was tested to identify the avoidance behavior of bottlenose dolphin by its working. However the efficiency of dual frequency AP about the study effect was verified experiment repeatedly using single and dual frequency AP.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.12
• /
• pp.1266-1273
• /
• 1991

Attenuation losses and repeater spans of single-mode optical fibers installed in the long hual optical transmission line were measured and analyzed. The average loss including splicing points was appeared to be 0.55 0.05dB/km and 0.59 0.01dB/km at 1300nm and 1550nm, respectively, and showed lager value at 1550nm window, The cause of loss increase at 1550nm range from the OTDR measurement was due to the inappropriate treatment of extra length of fiber at the splicing points. And average repeater span of domestic long haul line was 24 7km and 90% of total sampled repeater spans was within 31 km.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.4
• /
• pp.227-235
• /
• 1993

In this paper, the development of a high performance flexible controller is described. The hardware of the controller, based on VME-bus, consists of four M68020 single-board computers (32-bit) with M68881 numerical coprocessors, two M68040 single board donputers, I/O devices (such as A/D and D/A converters, paraller I/O, encoder counters), and bus-to-bus adaptor. This software, written in C and based on X-window environment with Unix operating system, includes : text editor, compiler, downloader, and plotter running in a host computer for developing control program ; device drivers, scheduler, and mathemetical routines for the real time control purpose ; message passing, file server, source level debugger virtural terminal, etc. The hardware and software are structured so that the controller might have both flexibility and extensibility. In papallel to the controller, a three degrees of freedom kinematically redundant robot has been developed at the same time. The development of the same time. The development of the robot was undertaken in order to provide, on the one hand, a computationally intensive plant to which to apply the controller, and on the other hand a research tool in the field of kinematically redundant manipulator, which is, as such, an important area. By using the controller, dynamic control of the redundant manipulator was successfully experimented, showing the effectiveness and flexibility of the controller.

• Animal Bioscience
• /
• v.37 no.5
• /
• pp.807-816
• /
• 2024

Objective: This study aims to identify the significant regions and candidate genes of growth-related traits (adjusted backfat thickness [ABF], average daily gain [ADG], and days to 90 kg [DAYS90]) in Korean commercial GGP pig (Duroc, Landrace, and Yorkshire) populations. Methods: A genome-wide association study (GWAS) was performed using single-nucleotide polymorphism (SNP) markers for imputation to Illumina PorcineSNP60. The BayesB method was applied to calculate thresholds for the significance of SNP markers. The identified windows were considered significant if they explained ≥1% genetic variance. Results: A total of 28 window regions were related to genetic growth effects. Bayesian GWAS revealed 28 significant genetic regions including 52 informative SNPs associated with growth traits (ABF, ADG, DAYS90) in Duroc, Landrace, and Yorkshire pigs, with genetic variance ranging from 1.00% to 5.46%. Additionally, 14 candidate genes with previous functional validation were identified for these traits. Conclusion: The identified SNPs within these regions hold potential value for future marker-assisted or genomic selection in pig breeding programs. Consequently, they contribute to an improved understanding of genetic architecture and our ability to genetically enhance pigs. SNPs within the identified regions could prove valuable for future marker-assisted or genomic selection in pig breeding programs.

• Smart Structures and Systems
• /
• v.33 no.6
• /
• pp.385-398
• /
• 2024

To improve the accuracy of time-frequency analysis (TFA) and instantaneous frequency (IF) extraction of structural dynamic response signals, this paper improves the spline-kernelled chirplet transform, and a new form of modified spline-kernelled chirplet transform (MSCT) based on revised Gaussian window function and energy concentration principle is put forward. The effectiveness of the proposed method is verified by numerical examples of single-component signal, multicomponent signal, single-degree-of-freedom Duffing nonlinear system and two-layer shear frame structure model. Then, a time-varying cable test is designed to collect the acceleration response signals under linear changing tension, and the IF extraction of these signals is performed by using MSCT, which further verifies the effectiveness and accuracy of this method. Through numerical simulation and experimental verification, it is proved that the proposed method can effectively extract the IF of nonlinear structure and time-varying structure.

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.52
• /
• pp.47-71
• /
• 2011

This thesis examines the problems faced in the electronic trade platform for which improvements are necessary, and suggests various ways of overcoming those problems. Practical implications regarding the advancement of Korea's u-TradeHub system are as follows. First, from the technical and legal aspects, to make up for a lack of support systems for spread of users, it is required to promote customized advertising strategies through Ministry of Knowledge Economy and establish a global certification system. Second, document standardization and digitalization should be achieved in advance to make the documents distributed through the e-Trade platform in a seamless manner. Furthermore, an ongoing global network development project should be promoted through the e-Trade platform to achieve standardization. Third, from the operational aspect, it is important to maintain an integrated and systematic relationship with related organizations. Because vertical integration among logistics service providers and GSCM are enabled through the e-Trade platform, it is necessary to standardize global network-based linkage and operating systems.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.111-111
• /
• 2012

In this talk, we represent a novel approach to investigating intra-nanorod surface plasmon coupling with control over block compositions. The multi-component rod-like nanostructures, which consist of optically active components (Au and Ag) and optically less active component (for example, Ni) in UV-vis-NIR spectral window, showed interesting optical response depending on each block length and the total length of the structure. By controlling the composition and relative lengths of the blocks that comprise these structures, we can tailor the overall optical properties. Depending on the relative fraction of Au and Ag blocks, the intensity of the transverse modes varied without noticeable peak shifts. However, the strong intraparticle surface plasmon coupling resulted in the collective appearance of longitudinal LSP modes, including higher-order modes. The experimental observations were confirmed by theoretical calculation, using a discrete dipole approximation method. In addition, we will briefly discuss how single nanorod solar cells can be synthesized by using by using electrochemical deposition and AAO hard templates.

• Computational Structural Engineering
• /
• v.3 no.4
• /
• pp.133-141
• /
• 1990

The nature of fluctuating air pressure inside building was studied by testing a building model in a wind tunnel. The model has a single room and a window opening. Various opening conditions were tested in both laminar uniform wind and turbulent boundary-layer wind. The RMS and the spectra of the fluctuating internal pressure were measured. The test results support a recent theory which predicts the behavior of internal pressure under high wind based on aerodynamic analysis.

• IE interfaces
• /
• v.12 no.4
• /
• pp.557-566
• /
• 1999

This paper considers a door-to-door service system in which pickups or deliveries are performed by a trip of a single vehicle. Each customer request specifies the quantity of the load transported, the location, and the time window within which it is to be picked up or delivered. Since the system is demand responsive, i.e., new or emergent requests become available in real-time, the current vehicle route has to be reconstructed to include these requests. In this case, only continuous vehicle tracking enables control over the requests and ensures that the requests are satisfied on time. This paper suggests a pilot pickup/delivery management system integrating a geographic information system(GIS) and a global position system(GPS) to efficiently deal with such a dynamic environment. The GIS offers a way of displaying the vehicle route on digital maps for the region under concerned. Also displayed is the current location of the vehicle obtained from the GPS. A heuristic algorithm is used to dynamically determine the vehicle route. A practical example is provided to show the feasibility of the system.