• Resources Recycling
• /
• v.16 no.5
• /
• pp.65-70
• /
• 2007

This study presents the findings of the experiments that were conducted on single- and multi-stage solvent extractors using the stimulus-response method, with the am of identifying flow characteristics of the material inside the mixer-settler-type extractor. The results of this study show that the response characteristics of a single-stage mixer is the same as that of a completely stirred tank reactor (CSTR), and that the lag time of a mixer-settler-type extractor increases with the number of its extraction stages. The experimental data for the single- and multiple-stage extractors were analyzed using K-RTD, a response analysis program, to obtain a retention time distribution (RTD) model of one-stage and four-stage extractors. The correlation coefficient between the calculated values and the experimental data was 0.963 for the one-stage extractor and 0.995 for the four-stage extractor, showing quite a good correlation.

• Advances in nano research
• /
• v.10 no.1
• /
• pp.15-24
• /
• 2021

Microtubules (MTs) are the main part of the cytoskeleton in living eukaryotic cells. In this article, a mechanical model of MT buckling, considering the modified strain gradient theory, is analytically examined. The MT is assumed as a cylindrical beam and a new single variable trigonometric beam theory is developed in conjunction with a modified strain gradient model. The main benefit of the present formulation is shown in its new kinematic where we found only one unknown as the Euler-Bernoulli beam model, which is even less than the Timoshenko beam model. The governing equations are deduced by considering virtual work principle. The effectiveness of the present method is checked by comparing the obtained results with those reported by other higher shear deformation beam theory involving a higher number of unknowns. It is shown that microstructure-dependent response is more important when material length scale parameters are closer to the outer diameter of MTs. Also, it can be confirmed that influences of shear deformation become more considerable for smaller shear modulus and aspect ratios.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.728-731
• /
• 1995

Miniaturzed specimen technology permits mechanical bechanical behavior to be determined using a minimum volume of material. because it is almost impossible to sample the conventional specimen for the fracture toughness test without damage to the rotor. In addition, it is different to collect a large amount of actual turbine rotor steels. Hence seven kinds of specimen with different degradation levels were prepared by isothermal aging heat treatment at 630 .deg. C. Test material was 1Cr-1Mo-0.25V steel which was widely used for turbine rotor material. The relation between fracture toughness and DBTT was investigated The characteristics of minaturized impact speciments technique was discussed. Finally, the estimating method of fracture toughness using a single impact specimen was introduced.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.4
• /
• pp.26-29
• /
• 2003

To discover electrical properties of individual single wall nanotube(SWNT), a number of SWNT-based tubeFETs have been fabricated. The device consists of a single semiconducting SWNT on an insulating substrate, contacted at each end by metal electrodes. It presents high transconductances, and charge storage phenomenon, which is the operations of injecting electrons from the nanotube channel of a tubeFET into charge traps on the surface of the $SiO_2$ gate dielectric, thus shifting the threshold voltage. This phenomenon can be repeated many times, and maintained for the hundreds of seconds at room temperature. We will report this phenomenon as the memory effects of the SWNT, and attempt to use this property for the memory device.

• Journal of Adhesion and Interface
• /
• v.7 no.4
• /
• pp.18-23
• /
• 2006

The influence of the notch length on the stress distribution of mid-bondline and adherend was investigated using elasto-plastic finite element method. The results from the simulation showed that peak stress of mid-bondline decreased markedly as adherend with notch in the middle of lap zone, and the stress in the middle of joint with low stress originally increased evidently. All the peak stresses decreased firstly and increased again as the length of notch increased. The relative higher peak stress appeared at the point near the notch of adherend where might be failed previously during the loading procedure.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.2
• /
• pp.269-275
• /
• 1990

Nonaxisymmetric bifurcation behaviours of composite tubes two different materials subjected to uniform radial shrinkage at the external surface have been investigated and compared with those of single tube. The effect of material parameters normalized with respect to those of outer tube upon the bifurcation point and corresponding mode has been clarified. The parameters substantially affect the bifurcation mode with long-wavelength so that the composite tube with low hardening exponent or with high yield stress of inner tube destabilizes the overall deformation of the tube. However surface type bifurcation, short-wavelength mode, shown on the traction-free inner surface is hardly affected by the material parameters. The surface type bifurcation completely depends on the material characteristics of inner tube and the bifurcation point of composite tube almost coincides with the of single tube.

• Journal of Korean Institute of Industrial Engineers
• /
• v.37 no.4
• /
• pp.279-288
• /
• 2011

The past researches focused on the supply chain network that consists of factories, distribution centers and retailers for single product type. This research is required because the factory for single product type is advanced to reconfigurable type in order to produce various products, according to customers' various purchase forms and time. This research is also required because in the past researches, the material flows from factories to distribution centers and from distribution centers to retailers, but recently, there are material flows between distribution centers. The supply chain network in this research consists of reconfigurable manufacturing system, multi-layered distribution centers, and retailers. A simulator is developed to analyze the material flow on the supply chain network. The developed simulator is web-based designed by using Java Server Page and MS-SQL, so as to maximize the convenience for users.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.6.1-10
• /
• 1996

Starting from the Debye theory of rotational Brownian motion equation, we derive an expression for explaining the generation of Maxwell displacement current (MDC) across single monolayers on a material surface. The orientational order parameter and the dielectric relaxation the of monolayers are derived. Based on fille analyses developed here, we examine the MDC across phospholipid monolayers with thermal stimulation due to the change in the spontaneous polarization, and the generation of MDC from 4-cyano-4\`-5-alkayl-biphenyl(5CB) Langmuir-film at the onset of transition by monolayer compression

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.79-81
• /
• 2000

Outdoor insulation of overhead distribution lines with wood, concrete and steel pole has been safety under various environmental conditions including contamination, moisture condensation, rain and lightning overvoltages. In this paper introduce to FRP technology of the power distribution single pole. FRP pole has been used very much as high strength material for insulators because of its high strength and good insulation properties. In addition, FRP pole was made by filament winding method. In a filament winding process, a band of continuous resin-impregnated rovings or monofilaments is wrapped around a rotating mandrel and cured to produce axisymmetric hollow parts.

• Smart Structures and Systems
• /
• v.2 no.2
• /
• pp.171-188
• /
• 2006

This paper deals with damage detection using active Lamb waves. The wavelet transform and empirical mode decomposition methods are discussed for measuring the Lamb wave's arrival time of the group velocity. An experimental system to diagnose the damage in the composite plate is developed. A method to optimize this system is also given for practical applications of active Lamb waves, which involve optimal arrangement of the piezoelectric elements to produce single mode Lamb waves. In the paper, the single mode Lamb wave means that there exists no overlapping among different Lamb wave modes and the original Lamb wave signal with the boundary reflection signals. Based on this optimized PZT arrangement method, five damage localizations on different plates are completed and the results using wavelet transform and empirical mode decomposition methods are compared.