• Journal of Navigation and Port Research
• /
• v.31 no.8
• /
• pp.689-695
• /
• 2007

The under developing estuarial port Bupsung is bounded by a river and the sea, and has several well developed tidal lands, where the littoral drift is strong due to the tide and the river discharge. The study area is located at the inner part of a concave bay and has a large tidal range due to the water discharge through the Watan-chun and Junnam-dike. In beginning stage of the ocean physical impact study, the tidal modeling is very important and difficult especially in this area. Moreover, we need a model experiment after the verification of the formulated model based on ocean survey. In this study, we constructed a numerical model to the Bupsung port coastal boundaries, which varies with the past and future development and made simulation with it. The result after development shows that there is a decrease of velocity on flood current and a increase on Ebb current and the minor variation of the tide level, compared with before development.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.2
• /
• pp.150-158
• /
• 2018

Numerical simulation and experimental study on the thermal flow field of the micro turbojet engine have been carried out for the purpose of developing infrared reduction technology for aircraft. A circular basic nozzle and five rectangular nozzles with different aspect ratio were considered. The conditions for CFD analysis were derived from the analysis of the engine performance. The temperature distribution of the nozzle plume was measured using a temperature sensing system. The thrust of the rectangular nozzle with the aspect ratio 5 was reduced about 1.8% compared to the circular nozzle, and the thrust decreased with increasing the aspect ratio of the nozzle. In the case of thermal flow field, it was observed that, as the aspect ratio increases, the exhaust plume in the experiment was formed wider than in the CFD analysis.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.5
• /
• pp.481-488
• /
• 2013

Nitric oxide ($NO_x$) formation characteristics in non-premixed diffusion flames of methane fuels have been investigated experimentally and numerically by adding 10% ammonia to the fuel stream, according to the variation of the oxygen ratio in the oxidizer with oxygen/carbon dioxide and oxygen/nitrogen mixtures. In an experiment of coflow jet flames, in the case of an oxidizer with oxygen/carbon dioxide, the $NO_x$ emission increased slightly as the oxygen ratio increased. On the other hand, in case of an oxygen/nitrogen oxidizer, the $NO_x$ emission was the maximum at an oxygen ratio of 0.7, and it exhibited non-monotonic behavior according to the oxygen ratio. Consequently, the $NO_x$ emission in the condition of oxyfuel combustion was overestimated as compared to that in the condition of conventional air combustion. To elucidate the characteristics of $NO_x$ formation for various oxidizer compositions, 1D and 2D numerical simulations have been conducted by adopting one kinetic mechanism. The result of 2D simulation for an oxidizer with oxygen/nitrogen well predicted the trend of experimentally measured $NO_x$ emissions.

• Horticultural Science & Technology
• /
• v.30 no.6
• /
• pp.650-656
• /
• 2012

The aims of the experiment, conducted over three years in the Central Europe field conditions, were (1) to investigate the effect of growing period (plantings in the middle and at the end of August: $1^{st}$ and $2^{nd}$ term, respectively) on yield and chemical composition of the non-heading Chinese cabbage (Brassica rapa var. chinensis) cultivars 'Taisai', 'Pak Choy White', and 'Green Fortune', and (2) to develop regression models to evaluate the changes in crop yields as a function of weather conditions. A highest marketable yield was obtained from 'Taisai' (65.71 and 77.20 $t{\cdot}ha^{-1}$), especially in the $2^{nd}$ term of production. Low yield, observed for 'Pak Choy White' was due to its premature bolting. Almost 39% ($1^{st}$ term) and 70% ($2^{nd}$ term) of plants of this cultivar formed inflorescence shoots before harvest. The highest dry matter level was observed in the leaf petioles of 'Taisai', while 'Green Fortune' was the most abundant of carotenoids and L-ascorbic acid. The content of soluble sugars was the lowest for 'Pak Choy White'. In a phase of harvest maturity, more of the analyzed constituents were gathered by plants from earlier plantings, and differences were as follows: 4.7% (dry matter), 26.3% (carotenoids) and 22.1% (L-ascorbic acid), in comparison to $2^{nd}$ term of production. Significant increase of soluble sugars level was observed for plants from later harvest. The regression model for marketable yield of Chinese cabbage cultivar 'Taisai' as a function of maximum air temperature can predict the yield with accuracy 68%. The models for yield or bolting of 'Pak Choy White', based on extreme air temperatures and sunshine duration, were more precise (98%). It should be pointed out that Taisai could be recommended for later growing period in Central Europe conditions with regard to maximum yield potential. 'Green Fortune' was notable for its uniform yielding. To obtained plants of higher nutritional value, earlier time of cultivation should be suggested. Described models can be successfully applied for an approximate simulation of Chinese cabbage yielding.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.11
• /
• pp.1423-1433
• /
• 2018

Recently, a permanent magnet synchronous motor of middle and small-capacity has high torque, high precision control and acceleration / deceleration characteristics. But existing control has several problems that include unpredictable disturbances and parameter changes in the high accuracy and rigidity control industry or nonlinear dynamic characteristics not considered in the driving part. In addition, in the drive method for the control of low-vibration and high-precision, the process of connecting the permanent magnet synchronous motor and the load may cause the response characteristic of the system to become very unstable, to cause vibration, and to overload the system. In order to solve these problems, various studies such as adaptive control, optimal control, robust control and artificial neural network have been actively conducted. In this paper, an incremental encoder of the permanent magnet synchronous motor is used to detect the position of the rotor. And the position of the detected rotor is used for low vibration and high precision position control. As the controller, we propose augmented state feedback control with a speed observer and first order deadbeat disturbance observer. The augmented state feedback controller performs control that the position of the rotor reaches the reference position quickly and precisely. The addition of the speed observer to this augmented state feedback controller compensates for the drop in speed response characteristics by using the previously calculated speed value for the control. The first order deadbeat disturbance observer performs control to reduce the vibration of the motor by compensating for the vibrating component or disturbance that the mechanism has. Since the deadbeat disturbance observer has a characteristic of being vulnerable to noise, it is supplemented by moving average filter method to reduce the influence of the noise. Thus, the new controller with the first order deadbeat disturbance observer can perform more robustness and precise the position control for the influence of large inertial load and natural frequency. The simulation stability and efficiency has been obtained through C language and Matlab Simulink. In addition, the experiment of actual 2.5[kW] permanent magnet synchronous motor was verified.

• Journal of KIISE
• /
• v.43 no.11
• /
• pp.1233-1244
• /
• 2016

In the IoT network environments for LLNs(Low power and Lossy networks), IPv6 Routing Protocol for Low Power and Lossy networks(RPL) has been proposed by IETF(Internet Engineering Task Force). The goal of RPL is to create a directed acyclic graph, without loops. As recommended by the IETF standard, RPL route recovery mechanisms in the event of a failure of a node should avoid loop, loop detection, DIO Poisoning. In this process, route recovery time and control message might be increased in the sub-tree because of the repeated route search. In this paper, we suggested RPL route recovery method to solve the routing overhead problem in the sub-tree during a loss of a link in the RPL routing protocol based on IoT wireless networks. The proposed method improved local repair process by utilizing a route that could not be selected as the preferred existing parents. This reduced the traffic control packet, especially in the disconnected node's sub tree. It also resulted in a quick recovery. Our simulation results showed that the proposed RPL local repair reduced the recovery time and the traffic of control packets of RPL. According to our experiment results, the proposed method improved the recovery performance of RPL.

• Journal of Distribution Science
• /
• v.14 no.5
• /
• pp.107-114
• /
• 2016

Purpose - Loading can decrease the productivity due to the possibility of carrying out with the opposite order of storage in container terminal. When the container is to be taken out, it is needed to move the container stacked upon the container to be carried out to other place temporarily. It is called as rehandling. Remarshalling, with the loading plan, is the arranging the containers before the ship arrives in order to avoid the rehandling during the carrying out. The present study tried to find out the factors affecting the efficiency when building the remarshalling plan with the utilization of neighboring storage space as a outer slot, and analyzed the efficiency of several remarshalling algorithms with the combination of those factors. Research design, data and methodology - The present study used, when the remarshalling plan is prepared for utilizing the outer slot, the simulation methods in order to compare the efficiency of the remarshalling algorithms which made with the factors affecting the efficiency. The factors affecting the efficiency are the method of making the child node, method of arrangement, and possibility of application of FIX. In order to analyze the affecting factors on the efficiency, several algorithms are prepared with the combination of production of the child node and the arrangement method with the availability of FIX application. With this algorithm, the effect of the factors on the efficiency after building up of remarshalling plan with the target on the bay with 10 rows, 8 columns, and 10 indices. Results - The method of rearrangement and making of a child node as the factor affecting the efficiency of remarshalling utilization of the outer bay were studied. It is efficient to combine the method of making a child node with MCS in order to reduce the number of moving the containers. For reducing the time in carrying out, it was found that all arrangement methods should be combined with RCS for the efficiency. The result of experiment shows the application of FIX with good result in case of succession ratio. In addition, when FIX was not applied, all of the most combinations resulted in short time in remarshalling. As a result, it can be concluded that the algorithm with proper combination of making the child node and the arrangement can increase the job efficiency based on the importance. Conclusion - The present study suggested and analyzed the algorithms with the combination of the arrangement method, the making of child node, and FIX. It is needed to develop the algorithm to judge the possibility whether the best remarshalling plan can be built or not within the bay in order to find a better method between the two cases such as within the bay and outer the bay. As a method for extending the study on the factors affecting the efficiency, it is possible to find out the way to build the remarshalling plan within the permitted time under any storage situation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.817-825
• /
• 2017

The AC-common bus microgrid system can overcome several weaknesses of the DC microgrid system by interconnecting the DC/AC inverters used for renewable energy with an AC network. Nevertheless, the unbalanced loads inherent in the electric power systems of island and small communities can deteriorate the performance of the AC microgrid system. This is because of the limited voltage regulation capability and mixed power flow in the voltage source inverter. In order to overcome the unbalanced load condition, this paper proposes a voltage and current control algorithm for the 4-leg inverter based on the single phase d-q control method, as well as the modeling of the voltage controller using Matlab/Simulink S/W. From the S/W simulation and experiment of the 250KW proto-type inverter, it is confirmed that the proposed algorithm is a useful tool for the design and operation of the AC microgrid system.

• Journal of KIISE:Computing Practices and Letters
• /
• v.13 no.5
• /
• pp.252-259
• /
• 2007

With the rapid development of multimedia applications and wireless communication networks, consumer demand for video-over-wireless capability on mobile computing systems is growing rapidly. In this regard, this paper introduces YUV-aware instructions that enhance the performance and efficiency in the processing of color image and video. Traditional multimedia extensions (e.g., MMX, SSE, VIS, and AltiVec) depend solely on generic subword parallelism whereas the proposed YUV-aware instructions support parallel operations on two-packed 16-bit YUV (6-bit Y, 5-bits U, V) values in a 32-bit datapath architecture, providing greater concurrency and efficiency for color image and video processing. Moreover, the ability to reduce data format size reduces system cost. Experiment results on a representative dynamically scheduled embedded superscalar processor show that YUV-aware instructions achieve an average speedup of 3.9x over the baseline superscalar performance. This is in contrast to MMX (a representative Intel#s multimedia extension), which achieves a speedup of only 2.1x over the same baseline superscalar processor. In addition, YUV-aware instructions outperform MMX instructions in energy reduction (75.8% reduction with YUV-aware instructions, but only 54.8% reduction with MMX instructions over the baseline).

• Proceedings of KOSOMES biannual meeting
• /
• 2006.11a
• /
• pp.181-186
• /
• 2006

Geostationary Orbit satellite, unlike other sun-synchronous polar-orbit satellites, will be able to take a picture of a large region several times a day (almost with everyone hour interval). For geostationary satellite, the target region is fixed though the location of sun is changed always. However, Sun-synchronous polar-orbit satellites able to take a picture of target region same time a everyday. Thus Ocean signal is almost same. Accordingly, the ocean signal of a given target point is largely dependent on time. In other words, the ocean signal detected by geostationary satellite sensor must translate to the signal of target when both sun and satellite are located in nadir, using another correction model. This correction is performed with a standardization of signal throughout relative geometric relationship among satellite-sun-target points. This relative ratio called bidirectional factor. To find relationship between time and $[L_w]_N$/Bidirectional Factor differences, we are calculate solar position, geometry parameters. And reflectance, total radiance at the top of atmosphere(). And water leaving radiance, normalized water leaving radiance. And calculate bidirectional factor, that is the ratio of $[L_w]_N$ between target region and aiming the point. Then, we can make the bidirectional factor lookup table for one year imaging. So, we suggested for necessary to simulation experiment bidirectional factor in more various condition(wavelength and ocean/air condition).