• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1986년도 하계학술대회논문집
• /
• pp.369-372
• /
• 1986

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.160-162
• /
• 2001

A determining method of the $\Gamma$ type eqivalent circuit parameters of induction motor driven by inverter source is proposed in this paper. The no-load test by rated frequency (60 Hz) and a blocked rotor test by 25% of rated frequency (l5Hz) are performed with inverter source, and the DC resistance of the stator winding is measured. To determine the more accurate parameters, four simultaneous equations obtained from equivalent circuit of the no-load test and blocked rotor test are solved by using initial values which are evaluated from simplified equivalent circuits. The induction motor performances are computed by using these parameters and compared with measured values of the tested motor. Then it is found that the compared results show good agreement between them.

• Journal of Magnetics
• /
• 제16권1호
• /
• pp.58-63
• /
• 2011

This paper presents design procedures of a transverse flux linear motor (TFLM). The minimum and maximum flux linkage was determined by the simplified equivalent magnetic circuit and estimated average magnetic flux density at the air gap region by considering the shape of applied magnetomotive force (MMF). With this information, the number of turns of each phase winding was calculated based on the amplitude of applied voltage and speed of a mover. The rated current, coil diameter, and winding area were obtained with the aid of an empirical formula for determining the required MMF. The usefulness of the proposed design method for TFLM is verified by the three-dimensional equivalent magnetic circuit network (EMCN) method and the experimental results of prototyped machine.

• Advances in aircraft and spacecraft science
• /
• 제2권3호
• /
• pp.275-302
• /
• 2015

Theoretical and numerical assessments of approximate evaluations and simplified analyses of piezoelectric structures transverse shear modal effective electromechanical coupling coefficient (EMCC) are presented. Therefore, the latter is first introduced theoretically and its approximate evaluations are reviewed; then, three-dimensional (3D) and simplified two-dimensional (2D) plane-strain (PStrain) and plane-stress (PStress) piezoelectric constitutive behaviors of electroded shear piezoceramic patches are derived and corresponding expected short-circuit (SC) and open-circuit (OC) frequencies and resulting EMCC are discussed; next, using a piezoceramic shear sandwich beam cantilever typical benchmark, a 3D finite element (FE) assessment of different evaluation techniques of the shear modal effective EMCC is conducted, including the equipotential (EP) constraints effect; finally, 2D PStrain and PStress FE modal analyses under SC and OC electric conditions, are conducted and corresponding results (SC/OC frequencies and resulting effective EMCC) are compared to 3D ones. It is found that: (i) physical EP constraints reduce drastically the shear modal effective EMCC; (ii) PStress and PStrain results depend strongly on the filling foam stiffness, rendering inadequate the use of popular equivalent single layer models for the transverse shear-mode sandwich configuration; (iii) in contrary to results of piezoelectric shunted damping and energy harvesting popular single-degree-of-freedom-based models, transverse shear modal effective EMCC values are very small in particular for the first mode which is the common target of these applications.

• 대한전기학회논문지
• /
• 제36권11호
• /
• pp.826-835
• /
• 1987

본 논문에서는 귀선기간동안 CRT 디스플레이용 수평출력 및 FBT단을 새로운 간략화된 등가회로로 나타내었다. 이 등가회로를 사용하여 회로해석을 한 후 계산결과와 측정결과를 비교하였다. 결과에 의하면, 다른 회호변수들이 일정할 경우 고전압 변동이 변압기의 결합계수, 정류다이오드으 전압-전류 특성 및 전하축적에 의존함을 보여준다. 계산결과는 측정결과보다 약 3.9% 내지는 5.8% 정도 높게 나타내는데 이것은 변압기 손실을 무시한 결과라 생각된다. 이러한 계산오차로 미루어, 본 등가회로는 그 타당성이 인정된다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2009년도 정기총회 및 추계학술대회 논문집
• /
• pp.252-255
• /
• 2009

This paper proposes a new loss minimization controller (LMC) for induction motor drive. The proposed LMC presents a strategy to minimize the total power losses of induction motor (IM), which is based on simplified equivalent circuit and simplified model of IM. The proposed controller using the field oriented control (FOC) method is to determine an optimal rotor flux for obtaining the minimum total power losses and higher efficiency. Simulation and experimental results are given to validate the effectiveness of the proposed method.

• Journal of electromagnetic engineering and science
• /
• 제13권2호
• /
• pp.134-136
• /
• 2013

This paper examines various aspects of the electromagnetic responses of the ring resonator located in the transverse electromagnetic cell. In addition, an equivalent circuit for the ring resonator is proposed and analyzed based on the electromagnetic phenomenon of the resonator. The equivalent circuit was simply modeled based on the concept of magnetization. A method for achieving a wider operating bandwidth of the negative permeability is provided. The ring resonator with its resonant frequency of 13.56 MHz was designed and its characteristics were examined in terms of S-parameters, effective permeability, loss rate, bandwidth, etc. The circuit and electromagnetic simulation results show an excellent agreement as well as that of theory.

• 반도체디스플레이기술학회지
• /
• 제17권4호
• /
• pp.56-61
• /
• 2018

In this paper, a new type of active snubber was proposed to lower the excessive rated voltage of the clamp capacitor which was a problem in the conventional circuit by applying auxiliary winding into the active snubber. A simplified equivalent circuit of the proposed snubber was derived by applying it to QR flyback converter, and the equivalent circuits for each switch state was shown under the steady-state condition. In addition, the maximum voltage of the clamp capacitor as well as the main switch was found by using the steady-state equations. In particular, it was found that the clamp capacitor voltage could be controlled by the auxiliary winding ratio. In order to verify the utility and practicality of the proposed converter with auxiliary winding type active snubber circuit, a prototype with an output voltage of 19V and a maximum load current of 6A was produced and the results were reported.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1987년도 전기.전자공학 학술대회 논문집(I)
• /
• pp.706-709
• /
• 1987

In this paper, the circuit analysis during the retrace period of E.H.T. generator is performed by means of the simplified equivalent circuit. The E.H.T. voltage and the beam current are computed by using Newton-Raphson method and the computed results are compared with those of experiment.

• 대한전자공학회논문지
• /
• 제26권9호
• /
• pp.1308-1316
• /
• 1989

A simplified 10-element GaAs MESFET equivalent circuit model has been presented which is suitable for the design of ultrabroad-band microwave small-signal amplification, the these circuit element values are extracted from measured S-parameters using complex-curve fitting algorithm. Packaged GaAs MESFET equivalent circuits are composed of intrinsic \ulcornermodel and several extrinsic elements at microwave frequencies, of which the largest effects are caused by package lead inductances. If these are eliminated from measured S-parameters, newly obtained S-parameters are closed to intrinsic \ulcornermodel, and the rest element values can be easily extracted. The modeling results applied to the packaged GaAs MESFET NE71083 are almost equal between the measure S-parameters and the mideled S-parameters within b 2% errors from DC to 8GHz, and errors are increased to \ulcorner% upto 12GHz wide bandwidth.