• 마이크로전자및패키징학회지
• /
• 제19권1호
• /
• pp.67-73
• /
• 2012

본 연구는 고밀도 미세회로 형성 및 원가절감에 유리한 페이스트의 인쇄/건조, 프리프레그 관통 및 적층 공법을 이용한 $B^2it$ 공법을 이용하여 FMC 기판을 제조한 후 열적 스트레스에 대한 범프의 계면반응 연구를 수행하였다. 열적 스트레스에 대한 Ag 범프의 접합 신뢰성을 조사하기 위해 열충격시험, 열응력시험을 수행한 후 전기적 특성 및 단면분석을 통해 균열발생 여부를 조사하였다. 또한 Ag 범프와 Cu 랜드의 접합계면에 대한 계면반응 특성을 분석하기 위해 주사전자현미경(SEM), 에너지분산스펙트럼(EDS) 및 FIB분석을 수행하여 계면에서 발생되는 확산반응을 분석하였다. 이러한 결과를 바탕으로 열적 스트레스에 대한 Ag 페이스트 범프/Cu 랜드 접합계면에서 계면반응에 의해 형성된 Ag-Cu 합금층을 확인할 수 있었다. 이러한 합금층은 Cu ${\rightarrow}$ Ag 보다, Ag ${\rightarrow}$ Cu 로의 확산속도가 빠르기 때문에, Cu층에서의 (Ag, Cu) 합금층이 보다 많이 관찰되었으며, 합금층이 Ag범프의 계면 접합력 향상에 기여하는 것을 알 수 있었다.

• 한국산학기술학회논문지
• /
• 제3권2호
• /
• pp.110-114
• /
• 2002

주얼리 제조 공정중 마스터패턴 제조 공정은 전체 제조원가의 20%를 차지하기 때문에 매우 중요한 공정이다. 지금까지는 수작업으로 왁스 패턴을 제작하고 이를 이용하여 석고형을 만들고 석고형으로 마스터 패턴을 제작하는 복잡한 공정을 거쳐 제작하였다. 본 연구는 쾌속조형기를 이용하여 듀라폼 재질의 몰드를 만들고 저융점합금을 이용하여 마스터패턴을 직접 제작하는 새로운 공정을 개발하였다. 듀라폰의 용융진이 190℃ 이므로 용융점 70℃의 Pb-Sn-Bi-Cd 계의 저융점 합금을 주물재료로 이용하여 마스터패턴을 제작하였다.

• 한국진공학회지
• /
• 제7권s1호
• /
• pp.50-56
• /
• 1998

Ion beam assisted deposition (IBAD) was successfully used to produce a dense and ultra-adherent Hydroxyapatite (HA) film on titanium alloy and alumina. Recently it is also proved that the HA coatings on alumina substrate treated with 20 ppm $AgNO_3$ had the structure of $(Ag, Ca)_10(PO_4)6(OH)_2$, which exhibited excellent antimicrobial effects. The present paper aims to morphlogically characterize the adhesion of macrophages on newly developed Ag-HA coated alumina and Ti6A14V substrates and to evaluate the biocompatibility of the coatings in vitro. It can be found that the cell number on alumina of the concentration of $AgNO_3$ in the treatment, the cell number on Ag-HA coatings decreased. Up to 20 ppm $AgNO_3$ by Ag-treatment, the morphological development of the cells on Ag-HA coating was similar to that of the cells on HA coating, suggesting the biotolerance of the Ag-HA coatings.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권9호
• /
• pp.572-577
• /
• 2000

This paper describes the test results of a single phase 3kVA high temperature superconducting power transformer. The tapes are made with Bi-2223 and have silver alloy as the matrix. Four double pancake windings are used. Among them two double pancake windings are connected in series for high voltage winding and the others are connected in parallel for low voltage winding. The rated voltage and current of primary winding and secondary winding are 220/110V. 13.7/27.3A. Fundamental characteristics are obtained through short circuit and no load test. The over load capability and characteristics are investigated.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.131-136
• /
• 2001

In this paper, a high-temperature superconductor(HTS) current lead operating in current sharing mode is described. The minimum heat dissipation and the optimum safety factor(cross-sectional area) is obtained analytically for partial current sharing HTS leads. It is assumed that the current lead is in conduction cooled state, and the sheath material is the alloy of silver and gold. The reduced cross-sectional area results partial current sharing state, and consequently reduces conduction heat transfer, but the Joule heat generation is increased. The optimized HTS current lead is different from the conventional copper leads. In the copper leads, the minimum heat dissipation is obtained for the zero gradient of temperature at warm end. However, the temperature gradient at warm end is not zero when the HTS lead operates at minimum dissipation state.

• 한국초전도ㆍ저온공학회논문지
• /
• 제2권2호
• /
• pp.15-19
• /
• 2000

The stability of variable cross-sectional area HTS current lead is considered. The cross-sectional area is varied to have a constant safety factor which is defined as the ratio of operating current and critical current of superconductor. As the constant area HTS lead, the variable cross-sectional area HTS lead also has three steady states above the bifurcation point and only one steady state below the bifurcation point. The temperature profiles and current sharing ratios for each steady state are calculated. The heat dissipation into cryogenic system for super-conducting, intermediate, and upper states are compared. For Bi-2333 sheathed with silver-gold alloy 2m length of current lead, and the maximum temperature of upper state seems to be burn-out free below 5m length.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 춘계학술대회 논문집
• /
• pp.15-18
• /
• 1996

The elemental segregation in the sputter-deposited AgInSbTe recording thin films was studied by means of Auger electron spectroscopy and ESCA for the specimens of as-deposited and as heat-treated conditions. Auger electron spectroscopy and ESCA revealed an extremely thin layer of elemental inhomogeneity, especially for the silver, even in as-deposited condition. The chemical analysis results obtained in this alloy system are discussed in terms of process parameters and target microstructure.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 A
• /
• pp.33-35
• /
• 1999

This paper describes the test results of the single phase 3kVA high temperature superconducting power trans-former. The tapes are made with Bi-2223 and have silver alloy as the matrix. Four double pancake windings are used in total. Among them two double pancake windings are connected in series for high voltage winding and two double pancake windings are connected in parallel for low voltage winding. The rated voltages of each winding are 220/110 V. Fundamental characteristics are obtained through short circuit and no load tests. The over load capability and characteristics are investigated.

• 보존과학연구
• /
• 통권14호
• /
• pp.45-76
• /
• 1993

Au-Cu alloyed coating layer were found by Hg-amalgam process and it seemed to be used Cu-amalgam process similar to Au-amalgam. Coated layer is dense and unique, Thickness of layer was 1.5 to $18.0\mum$ which had 95.3 to 99.8% purity of gold Matrix metal mostly cosists of forged copper alloy which had high purity and ferrite ($\alpha$) strusture. It showed excellent refining technical level at that time. Aowever, the nail, ferrous matrix used for strength needed, composed of silver foil packed and gold layer for adherence between ferrous matrix and gold layer

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2003년도 추계학술대회 논문집
• /
• pp.96-98
• /
• 2003

Many of research efforts have been focused on the improvement of critical current density Jc of silver-sheathed Bi-2223 tapes for practical applications of material. Bi-2223 superconducting wires with 55 filaments were fabricated by stacking, drawing process with different heat-treatment histories. After rolling process, Bi-2223 tapes were heat-treatment at 780~826$^{\circ}C$ with variable mass flow rate of mixed gas. In this study, the effect of changes in the variable mass flow rate of mixed gas during the heat treatment of Bi-2223/Ag tapes has been investigated. Distinct differences were observed in the Bi-2223 phase and critical current as flow rate of mixed gas. We could achieve proper conditions of mass flow rate of mixed gas for Ag-alloy clad Bi-2223 superconducting tapes.