• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.1
• /
• pp.47-56
• /
• 2017

In this study, the higher temperature thermal property of the fly ash-blast furnace slag system Geopolymer including alumina aggregate was investigated whether that Geopolymer will be or not useful as thermal-resistant construction materials. Under every mixing conditions, the crack on the surface of hardened body was not observed up to $800^{\circ}C$ and it corresponded with fact that level of changes was not significant before and after heating process. Residual compressive strength is most high when mixing Blast-Furnace Slag ratio is 60 wt% until temperature reaches $800^{\circ}C$. The major hydrates of hardened body of Geopolymer; amorphous halo pattern between $20{\sim}35^{\circ}$ (2theta) and mullite ($3Al_2O_3{\cdot}2SiO_2$) and quartz ($SiO_2$) was found during the experiment. Amorphous halo pattern was a aluminosilicate gel generated by geopolymeric polycondensation and it was found that the halo pattern of aluminosilicate gel was preserved up to $800^{\circ}C$. The patterns of aluminosilicate gel disappeared from $1,000^{\circ}C$ and crystal phases like gehlenite, calcium silicate, calcium aluminum oxide, microcline was observed with the increase of exposure temperature.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.8
• /
• pp.2358-2366
• /
• 2013

Iron oxide (ferrihydrite, hematite, and magnetite) coated silica gels were prepared using a low-cost, easily-scalable and straightforward method as the adsorbent material for arsenic removal application. Adsorption of the anionic form of arsenic oxyacids, arsenite ($AsO^{2-}$) and arsenate ($AsO{_4}^{3-}$), onto hematite coated silica gel was fitted against non-linear 3-parameter-model Sips isotherm and 2-parameter-model Langmuir and Freundlich isotherm. Adsorption kinetics of arsenic could be well described by pseudo-second-order kinetic model and value of adsorption energy derived from non-linear Dubinin-Radushkevich isotherm suggests chemical adsorption. Although arsenic adsorption process was not affected by the presence of sulfate, chloride, and nitrate anions, as expected, bicarbonate and silicate gave moderate negative effects while the presence of phosphate anions significantly inhibited adsorption process of both arsenite and arsenate. When the actual efficiency to remove arsenic was tested against 1 L of artificial arsenic-contaminated groundwater (0.6 mg/L) in the presence competing anions, the reasonable amount (20 g) of hematite coated silica gel could reduce arsenic concentration to below the WHO permissible safety limit of drinking water of $10{\mu}g/L$ without adjusting pH and temperature, which would be highly advantageous for practical field application.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.2
• /
• pp.61-70
• /
• 2019

Geopolymer is an eco-friendly construction material that has various advantages such as reduced $CO_2$ emission, fire resistance and low thermal conductivity compared to cement. However, it has not been many studies on the thermal behavior of the surface of the geopolymer panel when flame is applied to the surface. In this study, surface characteristics of hardened geopolymer on flame exposure was investigated to observe its characteristics as heat-resistant architectural materials. External structure changes and crack due to the heat shock were not observed during the exposure on flame. According to the residue of calcite and halo pattern of aluminosilicate gel, decarboxylation and dehydration were extremely limited to the surface and, therefore, it is thought that durability of hardened geopolymer was sustained. Gehlenite and calcium silicate portion was inversely proportional to quartz and calcite and significantly directly proportional to BFS replacement ratio. Microstructure changes due to the thermal shock caused decarboxylation and dehydration of crystallization and it was developed the pore and new crystalline phase like calcium silicate and gehlenite. It is thought that those crystalline phase worked as a densification and strengthening mechanism on geopolymer panel surface.

• Journal of Pharmaceutical Investigation
• /
• v.3 no.1_2
• /
• pp.34-50
• /
• 1973

There are many reports on the stability of drugs in powders and tablets. The stabilities of ascorbic acid in the antacid preparations, such as calcium carbonate, magnesium carbonate, magnesium trisilicate, magnesium alumino silicate, and dried aluminum hydroxide gel under various humidities were examined. From the result of the experiment, it was assumed that the concentration of ascorbic acid, the amount of water-vapor sorption, and the physical character of the antacid ingredients were the main factors, influencing the degradation of ascorbic acid. The ascorbic acid, mixed with carbonates, such as calcium carbonate, was degradaded rapidly, while the preparation with dried aluminum hydroxide gel was slightly degraded after 10 days. A 2% ascorbic acid in the prepation was rapidly degraded than 10% ascorbic acid in the preparation.

• Macromolecular Research
• /
• v.13 no.2
• /
• pp.96-101
• /
• 2005

Thin-film humidity sensors were prepared using inorganic/organic hybrid polyelectrolytes, which were prepared from the sol-gel reaction of copolymers of [2-(methacryloyloxy)ethyl]dimethylpropylammonium bromide (MEPAB), n-butyl methacrylate (BMA), and 3-(trimethoxysilyl)propyl methacrylate (TSPM) with tetraethyl ortho-silicate (TEOS). The humidity-sensitive polyelectrolytes were composed of the copolymers having the following mole ratios of MEPAB, BMA, and TSPM: 60/30/10, 55/30/15, and 50/30/20. We found that the impedance varied with the content of MEPAB or TEOS; it ranged from $10^{7} to 10^{3}\Omega$ between 20 and $95\%$ relative humidity, which is the range required for a humidity sensor operating at ambient humidity. In addition we investigated a number of characteristics of these humidity sensors, such as their hysteresis, response time, temperature dependence, frequency dependence, water durability, and long-term stability.

• The Korean Journal of Ceramics
• /
• v.6 no.1
• /
• pp.37-42
• /
• 2000

To reduce shrinkage and the possibility of fracture during ambient pressure drying, it is of great importance to increase the strength and stiffness of the wet gels. In this paper is presented the strengthening and stiffening of wet silica gels prepared from sodium silicate (water glass) as well as properties of the corresponding xerogels. By washing gels containing different initial silica contents in water solutions at elevated pH, a maximum in shear modulus of ~4 MPa was obtained. The maximum stiffness enabled xerogels with bulk density of 0.28g/$\textrm{cm}^3$ to be made regardless of silica content and washing conditions. However, by aging the wet gels in a solution providing fresh monomers to the gel network, a shear modulus of 20 MPa was obtained after 27h. By this method monolithic xerogels with a density down to ~0.2g/$\textrm{cm}^3$ was prepared. The results are compared to alkoxide based gels.

• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.79-85
• /
• 1997

In order to improve the surface characteristics of polymethylmethacrylate(PMMA), oxide thin film coatings were applied using the sol-gel dip-coating technique. The $Si(OC_2H_5)_4$, tetra-ethyl-ortho-silicate(TEOS) was used as a starting material for $SiO_2$ coating. The hardness of the alkoxy-derived oxide-coated PMMA was increased from 190 MPa for non-coated PMMA with increasing film thickness. By optimizing the heating conditions and the hydrolysis conditions, a maximum apparent hardness obtained In the present study was achieved 310 MPa using the withdrawal velocity of 5cm/min and heat treatment at $90^{\circ}C$ for 5 hours, which is about 1.6 times larger than that of uncoated PMMA.

• Korean Journal of Metals and Materials
• /
• v.48 no.9
• /
• pp.831-841
• /
• 2010

Indium tin oxide (ITO) nanopowders were synthesized by coprecipitation and the sol-gel method to prepare a stable dispersion of ITO nano-colloid for antistatic coating of a display panel. The colloidal dispersions were prepared by attrition process with a vibratory milling apparatus using a suitable dispersant in organic solvent. The ITO coating solution was spin-coated on a glass panel followed by the deposition of partially hydrolyzed alkyl silicate as an over-coat layer. The double-layered coating films were characterized by measuring the sheet resistance and reflectance spectrum for antistatic and antireflective properties.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.12
• /
• pp.1181-1186
• /
• 2000

The structural evolution during the thermal treatment of $70SiO_2-3OTiO_2(mole%)$ sol-gel derived powders and films was investigated by FT-IR, Raman and XPS, and XRD. From these results, the $TiO_2-rich$ regions involving $Ti^{4+}$ ions in octahedral coordination were confirmed to be amorphous at $600^{\circ}C$. However, Raman spectra along with XRD patterns indicated that at high temperature (above $700^{\circ}C)$, the amorphous $TiO_2was$ segregating to form anatase crystal. Also, the effect of experimental variables such as thermal treatment, heating rate and exposure to water vapor on structural changes, refractive index and thickness of the film coated on sodalime-silicate glass were investigated.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.131-131
• /
• 2003

The advent of photonic technologies in the field of communications and data transmission has been heavily increasing the demand in integrated optical (IO) circuits capable of accomplishing not only simple tasks like signal, but also more sophisticated functions like all-optical signal routing or active multiplexing/demultiplexing. In the last decade, sol-gel technology has been widely used to prepare optical materials. Sol-gel processes show many promises for the development of low-loss, high-performance glass integrated optical circuits. However, crack formation is likely to occur during heat treatment in thick gel films. In order to overcome the critical thickness limitation, the organic-modified silicate has been widely used. In this case coating matrices have been prepared from the organo-silanes of T structures, acidic catalyst and the as-prepared gel films have been heat-treated below 200$^{\circ}C$ to avoid the crack formation and the degradation of organic components. However, the films prepared in the acidic condition and the low heat temperature make the films contain high OH groups which is the major optical loss function. In this work, C$\sub$6/H$\sub$5/SiO$\sub$1.5/ films were prepared on silicon substrate by sol-gel method using base catalyst in a PTMS/NH$_4$OH/H$_2$O/C$_2$H$\sub$5/OH system. The sol showed spinable viscosity at 50 wt% of solid content, and neglectable viscosity change with time. The films were crack-free and transparent after curing at 450 $^{\circ}C$, and highly condensed to minimize OH content in C$\sub$6/H$\sub$5/SiO$\sub$1.5/ networks. The effects of heat treatment of the films are characterized on the critical thickness, the chemical composition and the refractive indices by means of SEM, FT-IR, TGA, prism coupler, respectively.